glo hyper x2 case 3d models

The main goal of this project was to provide a sealed case with minimal inner volume for filament spool, which could be used during printing or for storage when filament is not being used. Small internal volume will only require small amount of...

In this case you can change those components for update or other use in the future.The display is via I2C protocol and a 4 pin JST-XH wire connected to be flexible for placement.The Mini 360 gets its power via a DC jack plug or by a screw connector,...

*In case anyone is interested in building a Mosquito/NF Crazy bowden tool, the bowden adaptor I've used can be found [here, PC4-M6](https://www.aliexpress.com/item/4001021932385.html?spm=a2g0s.9042311.0.0.27424c4ddlKGv8) and I simply screwed it into...

The other two holes are intended only in case the prints are not so successful and is needed to eliminate spaces between prints. I printed the feeder_top and feeder_bottom_xxx feeder itself using a 0.4 nozzle and a layer height of 0.28. The lower...

In my case I am running this with a GRBL control board. If you want to use my electronics board, use Fritzing (see: https://fritzing.org/ ) to open the file uStepperV4_OpenLoop_Interface_V1.fzz. The board allows for a tidy installation on the arm...

Soldering Board: Solder the amplifier board and put it into the electronics case. Attach all cables. Installation and Calibration: Attach the device to your water meter. Turn on power for electrical components. Move the photo transistor sled with...

This holds not only the trays, but also the chess fields in place, in case your flow was set a little too low. To connect the hinges, I recommend two paper clips pulled apart. Insert one from the left and one from the right. No support material is...

... gear 12v motors Credits: The DIN files are from another contributor, "imstrng," on Thingiverse. I included them in this post in case theirs is ever removed as they are incorporated into this project. ... https://www.thingiverse.com/thing:2610621

In this case, the power into the lever equals the power out, and the ratio of output to input force is given by the ratio of the distances from the fulcrum to the points of application of these forces. This is known as the Law of the Lever: T1 =...

In this case, please contact, it is possible to save files at high values, but this will give a sharp increase in file size. This is a fully solid-state version for 3d-print, this is not a scan version. At the photos you can see the contours of the...

I added a notch along the base of the extruder ones; my earlier test prints didn’t quite fit snugly, so that’s a pilot hole in case you need to tap in a small screw to hold against the flat side of the post. Filament: I did one test print using a...

Yatl – Jadeshell BeautyAs is often the case with amphibian and reptilian creatures of the Arba Forest, it's challenging for a human to distinguish between a female and a male Turtlekin. Yatl, a Turtlekin explorer, stumbled upon an ancient cursed...

Put new assembly together with the Main Body (Again, please make sure it can move over the main bolt freely). Tighten the screws so the gap between the jaws is 39-40mm Enjoy your new clamp!  Longer boltsIf the 80mm bolt is not long enough you can use...

Not a problem with a well-tuned MK3S+.    The box was printed usingFilament                                              ...

Parts you'll need are: - Print out two sets of the STL files for top and bottom - 3 x 8.3mm OD x 300mm long carbon fibre rods - 4 x rail buttons (https://ausrocketry.com.au/hardware/launch-lugs-rail-buttons/rail-buttons-small-1010-pair.html) - 4 x...

In any case, I've uploaded another version which has a bolded font and offers improved legibility. By the way, if you want to **save yourself some filament**, *don't bother printing it with infill set any higher than 30%*. Even printing it at 20%...

Worst case is it starts a fire so please make sure to use LED light bulbs as they don't even make the plastic cover warm in my experience. It was made as 2 parts so that you can get the LED bulb inside it. You put the base plate on first, Insert the...

The separate stairs are to replace broken ones, just in case ... The 45° or the 135° at 0.035mm layer height will match the pixel size of my printer (0.035mm), optimise angle according to your needs. ###Post Printing You have to cut the...

In this case, please contact, it is possible to save files at high values, but this will give a sharp increase in file size. This is a fully solid-state version for 3d-print, this is not a scan version. At the photos you can see the contours of the...

This matches up to the corner braces I uploaded here: https://www.thingiverse.com/thing:6212007 In this case this piece is to cut out and replace the pin section as that is a weak spot and can be bent as you see in my attached photos. You could of...

Just in case you want to try, I have two sets of fuse halves. One with a cavity and a hole in the top that makes it look like a whale blow hole to add small lead shot and one solid one. The one with the cavity also has a launch hook. Small planes...

What could be more obvious than to attach a small cheap air pump almost invisibly to the bike, so that you can fall back on a pump in case of need instead of pushing? This air pump was chosen because of its dimensions and price: (RUNACC)...

If your puck emits bubbles it means an air pocket has been breached, in which case the puck may sink a bit (which protects it in the oil). Using this puck requires an open flame. Take all prudent precautions, keeping the flame away from flammable...

In this case, you'll need also 7 slider and 5 stopping parts. For the left angular drawers, you can just mirror the object along the X-axis._ **HOW TO PRINT:** This depends on your printer. I've printed all the drawers upside down so that the...

The spring will need to be compressed to 25mm for it to fit inside the casing properly and return to centre. This can then be screwed into the handle with the m6 x 18 countersunk bolt. once this has been done, fit the penny washers into the handle...

Therefore, I created two of the same case parts for different board thicknesses: a) Electronics 1,5mm PCB.stl -> for 1,5mm thick PCB b) Electronics 1mm PCB.stl -> for 1.0mm thick PCB Other files: body.stl -> main body, holds the cell and runs the...

***Original Post*** I know there are improvements that can be made to this design, but I wanted to publish this "prototype" in case someone had an immediate need for such a mount and/or didn't want to wait for a more refined model. (Also, I don't...

A bolt-down TPU mount/case for your Action 2 camUpdate: Tested and fit with multiple different people all across the world! I've now included 15 through 40deg tilts for most mounts.Three different ND Filters!1) FreeWell filter, 1.8mm thick...

In my case I used the Slice Engineering stuff. Here's the deal... take the Boron Nitrate (yes you need this). Take your heater block and put a small amount into the heater and thermistor hole. Slide in the Heater, all the way, and be prepared to...

Haha, ironic lower case - isn't that just too funny? Grab your SnakeBlaster here: https://www.thingiverse.com/thing:3890229 Feedback is very welcome and though I might not respond to everyone, I read everything. If you run into issues, I'll do my...