kobra go firmware 3d models

If you have problems I'm probably not going to be available to help you, I have a other things to do! So do as I do and Google it. METHODOLOGY My Halloween display is managed by a Raspberry Pi based controller running custom software written in...

Be aware that the Noctua fan is quieter than the stock fan, but may not provide as much airflow, if you chose to go that route. This can lead to "Heat Creep" issues, if using an All Metal Hotend with PTEG or PLA filaments in lower airflow...

You will need 4 standard skateboard bearings, 22mm OD / 8mm ID / 7mm Thick I prefer the Thicker Spinner Body (this is what is in the picture) Print 2 Center Spinner Caps (I prefer the thin ones) Print 3 Blank Spinner Caps (These caps go on the...

INSTRUCTIONS -------------------------------------------------- For the most part it's pretty much common sense where the pieces go and can tell just by looking at the pictures I have uploaded. (I'll clean up and get better pictures soon.) I have a...

Repositioning of the extruder: I decided to go ALL the way in shortening the filament tube, so I chose the spot you see in the photos. I haven't seen anyone else trying this position but I can assure you it is possible. If you decide to go this...

Cut the cork tile to match the heating element’s size and blank out the regions where the thermistor and the power terminals go. Solder the power leads, LED and resistor to the marked side of the heating element; make sure the solder...

Using M3 screws of sufficient length (M3x25mm is good, round or button head recommended), drive them into the holes that go all the way through the shaft. If you printed the included hopper body (ABS!), the screws need to be driven through so that...

https://www.thingiverse.com/thing:3098955 Props also go to magdong for pointing out that a 5V high CFM fan would work better than the 12V version I originally suggested. What do you need? 2x 3m screws that are long enough to hold your fan into place....

You could optionally leave out the right-most insert and use a longer M3 screw in that hole that would go all the way to the threaded insert on the original SV-01 plate, going through both the shroud and adapter plate.Insert an M2 nut into each of...

The 3mm ID 4mm OD size is great because it is loose enough that 1.75mm filament slides through it without resistance but it fits inside a pc4-m10 fitting well...

If you want to go further and make it fully smooth and painted, I would give a solid 150-250 grit sand on the whole body to get a base surface to work with. Find any places with holes or defects and fill them with wood putty or body filler and sand...

Ear Cuffs & Hugs: A fusion of style and comfort, our ear cuffs and hugs are perfect for those who want to make a statement without going overboard. Sui Dhaga: Timeless elegance personified, our sui dhaga is an exquisite blend of traditional...

 Foam card (if you're not already familiar with it) is a material used in the art world and in crafting or modelling situations, a layer of foam is sandwiched between 2 layers of card, the resulting material is incredibly strong and is generally...

No brim is needed for PETG.For the stand, in PrusaSlicer go to Print Settings > Advanced and set "Elephant foot compensation" to zero, otherwise the brim may not stick to the part. ...The part is already designed with a slightly smaller first layer...

I'm including my PrusaSlicer 3MF file, so if you use PrusaSlicer it should be all ready to go for you. I picked up a two pack of the cables and printed two docks/dock bottoms and a single shell so I could have a dock at work, too. It's working very...

I hope you like it. This design uses a standard violin bridge, allows for a standard shoulder rest and allows for a traditional style 3D printed chin rest (included and set up for screw on brackets). If you prefer, I've also included blank pieces of...

O-rings I got mine on Amazon as follows: 031 Silicone O-Ring, 70A Durometer, Red, 1-3/4" ID, 1-7/8" OD, 1/16" Width (Pack of 25) https://www.amazon.com/gp/product/B000FMYO6Y/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1 023 Silicone O-Ring, 70A...

But I don't understand why fusion360 and AutoCAD are going so badly for me (I mean, not bad, but it doesn't have the performance it should), then you see the ram and it's halfway, the processor and although it usually maintains almost the base...

If you decide to go for this option, make sure the toolhead can reach the opposite corner and that the PTFE tube follows a natural path without any restrictions. DisclaimerAvoid using any Carbon Fiber polymers (or any other abrasive options) to...

i am making these to sell on ebay if you want one and do not have the tools or patiance of making these they are a lot of milling so far i have 3 single cooling blocks about 8 heat blocks and 1 or 2 duo blocks also there are 2 differant duo blocks...

Although it’s a bunch to read, please go through all the description and printing instructions before making those masks. -----Caution----- As we know, masks that are worn warm up by breath and body temperature. In addition, printed items offer a...

Slotin instructed one of his colleagues to lay radioactivity-detecting film badges around the area, which required the scientist to go dangerously close to the still overheated core. The errand resulted in no useful data, and was mentioned in a later...

If you do it slowly, don't get agressive, and sometimes consider to untighten a few millimeters, then it will all go well. Now, do the same with the lower ring (the three triangular holes at the inside of the lower ring will later be attached to the...

Going a bit further I put a thin bead of clear silicone caulk under the outer edge of the top cap and around the center screw to keep moisture out. With everything back together and adjusted I used more clear silicone and loaded up the pinch-slot on...

The basic elements are as such : cubes, the primary of the setstairs, that can be put over the cubescorner, that helps you orientate your paint system on a 30° anglecorner stairs, to put over themstairs top, if you want to go up on the wall.The...

... outlet on the power supply box). Also miscellaneous wires and crimp connectors for the various wiring connections. All parts that go inside the drybox were printed in PETG for temperature resistance. ... I printed the power supply box with PLA.

Move the socket towards the remaining housing, as the PCBs are going to be assembled now. Use 6 of the M3x12 screws to fix them - no need to fully tighten them, as this setup shall keep them in place only. SD Card adapter cable As the PCBs are fixed...

Just put it in from behind.ThanksThanks go out to triptych for his openSCAD file of the simple photo frame!Other modelsAlso have a look at all my customizable creations. There are more configurable-text-based creations, multi-line label, gadget...

Fixed spacing issues with screw holes.2x bottom final.stlAdded room for a small screwdriver for on the go servicing, and converted all heat set insert holes into captive M3 nuts. Added retaining clips for the negative power lead, tightened tolerances...

My first print of the cup was also from PETG, so if you do not want to go fancy, just stick with PETG.I have printed all parts on the textured PEI powder-coated spring steel sheet (I really love this sheet and only use the smooth sheet for TPU and PC...