log by bulb 3d models

https://american-photonics.myshopify.com/products/k40-reverse-laser-alignment-nut You can buy a “boresight laser” and easily make your own, these boresight lasers cost about U$12-20 online and I think that's what APC uses anyway. When you've got the...

If the slot is already occupied by another token, the player takes the token (a virus token for the first uninfected player but eventually could be either an antibody or virus token). If any player takes a virus token from any slot, that player...

If you're an electronics expert like me, you could probably get by with just buying the display and some resistors and skipping the I2c backpack altogether, opting for a protoboard or even posterboard to hold the display in. If you go that far, you...

Clean up any leftover supports on the letters by rubbing your (gloved) thumb across them or the back of a hobby knife. There will be some scarring on the side of the ring from the heavy supports which cannot be avoided. To color the ring letters,...

 You don't want a hot cup of coffee wrapped by a soft holder.   I also added an modifier in my slicer software to give the risers of the handles (side parts) a 30% infill instead of 15%.You can quickly see if this is going to fit your favorite cup if...

By this I mean mainly PCB clips and adapters, but also things that should make "Sammy" more beautiful. ### November 28, 2020: A well-rounded affair Of course, my Sambucca is not allowed to roll through the world on standard rims, sporty custom...

Yosemite Sam, a cartoon character in the Looney Tunes and Merrie Melodies series of short films produced by Warner Bros. He is commonly depicted as an extremely aggressive, gunslinging outlaw or cowboy with a hair-trigger temper and an intense...

Lengthwise, the bumper should extend beyond the wing by about 0.5 mm on each side. This will prevent the sides of the wing from contacting the case. (4) Insert switches and keycaps into plate and PCB. (5) Clip the gasket wings onto the plate...

The base plate consists of two parts (Base1, Base2), which can be connected and secured by inserting into the frame (BaseHolder). Removability is required to remove the product from the mask.</p> <p>After the clamps have been printed, it is necessary...

The cookie cutter designs are partly based on 3D models from our [3D museum](http://sketchfab.com/NHMWien) and were designed by Viola Winkler. The scan team of the NHM Vienna wishes you a wonderful holiday season, lots of fun baking cookies and a...

The cooling is done by a Peltier element with both passive and active cooling. The whole system is running on 5V with power consumption of approximately 1A. This makes it suitable as a USB powered device. Furthermore, it allows using a power bank as...

No piece can jump over another piece. Special Case #2: Thor (#10) is your strongest charactor, but can be defeated by Vala (#1) - If Vala (#1) attacks the opposing forces Thor (#10) - Thor loses if Thor (#10) attacks Vala (#1) - Vala loses! - Vala...

Wally Gator, from an American animated television series produced by Hanna-Barbera Productions that originally aired as one of the segments from the 1962–1963 block The Hanna-Barbera New Cartoon Series. Wally is an anthropomorphic, happy-go-lucky...

January 2022 For those who prefer to launch the plane by hand I uploaded a launch handle with counter plate. launch handle AD.stl counter plate AD.stl M2x12 screws are needed to screw it on. For the middle screw, a screw hole of the fuselage...

4- The model stands by itself using the print parameters noted above. If a higher infill is used on the head, the model may become top heavy. Use your discretion for different printing parameters. I would suggest higher infills for all parts...

He does have one weakness, he can be calmed by almost any music. No supports are required. If you have the proper filament colors, no painting is needed. The assembled model is 270mm tall. Enjoy! Print Instructions: Supports: No Resolution:...

Oh, and by the way, I just got my wooly nylon thread in the mail, I separated out an individual fiber and it is awsome, It will totally work. Give me a bit and I'll print another one to show you all how it looks. you can get some at:...

Speedy Gonzales, a cartoon character in the Looney Tunes and Merrie Melodies series of short films produced by Warner Bros. He is portrayed as "The Fastest Mouse in all Mexico" with his major trait being the ability to run extremely fast. Many...

The USB break-out board will be held in place by the 2 posts in the print - so it doesn't need to be fastened. 8. Connect all wires as indicated in the wiring diagram. This is where I found the lever nuts helpful so I could disconnect and...

The aircraft's propulsion system is powered by a custom-designed electric motor, which provides a high level of efficiency and reliability. The battery pack is designed to provide a long flight time, and the power management system ensures that the...

This is a remix of Combination Safe by ChuTec_Engineering_Solutions (https://www.thingiverse.com/thing:1939676).I liked the idea of the combination lock. But the box itself looked too much as a toy, too much simple. So I created my own model of the...

:DThe part should keep in place by itself, but if it doesn't a piece of double-sided tape can be a great helper.Next, you need to assemble the holder. Make sure you have 4 clamps handy, you'll need them in a second.The idea is to put a bit of...

The hole on my cooler is precisely 9.7 mm in diameter, so this plug should fit perfectly on many coolers made by different manufacturers. However, I've included the design files, so you can adjust them to suit your needs. To ensure a watertight...

Using the nose cone hammer in 8mm id bearings onto shafts, ensure they don't come off by pulling. There is a 3mm screw that fits between the two bearings on each blade, insert one of the angling arms in and drill a 3mm hole, insert a 3mm screw. ...

(You wont be able to seperate them by just pulling)** **Hooks are pressed into the holder contour of the module with an 90° angle and then rotated to correct direction. ...Make sure, you press them all the way in before rotating.** As already...

At the photos you can see the contours of the models on screens with stl or obj files, it is enough to understand the possibility of printing a model or producing a model by a cnc machine It is possible to model anyone another model according to...

once reassembled (by holding the shell together, maybe only two or three screws) hold together and slide the new shell over the rear half of the blaster. 3. Mark the holes with permanent marker to drill out with a 1/4" bit 4. Dismantle the...

I was really surprised by the "creep ride" of the Buratinu. I tried to "starve" it several times in glide to see the behavior during stall. I had to wait a long time and then it merely took the nose down slightly to pick up speed.The 1600 is a...

Another change I made was to the "X_Carrier_Right_V1.1TBS.stl" file by adding a backstop for the X axis guide rods. While I'd never used a tensioner before on either my A8 or A8 Plus, I assumed that my tensioner design was just going to be a dandy....

The servo I'm using is emax es08ma , other similar 9gram servo should be ok but not tested" Parts needed: 1x Arduino Pro Mini https://goo.gl/D2z6b4 1x Bluetooth Module https://goo.gl/hRQhzv 3x SG9 servos https://goo.gl/fRvFBf 1x On/Off switch...