log by bulb 3d models

For kids with ADHD, autism, or those who just learn differently, a spinner can be a discrete, quiet means of staying on task by occupying their hands. Incorporated into an IEP, they can be extremely helpful. After designing a couple of minimalistic...

I had to compromise some design aspects for this version because I wanted to give more clearance between the base of the Shroud and the nozzle to there is less chance of any deformations causing problems by hitting the prints. Therefore V3 loses...

But this way it's more in line in how the pegboards are supposed to work.Parts included (for now):mini-ITX motherboardGPU mounted vertically on a riser cable (screw holes for 3 slots)PSU (HDPLEX 400W HiFi DC-ATX + AC-DC combo)power button (the very...

There are two versions of a motor ESC holder (Square tube doesn't need this) one loops round the tube to give a flat surface, the other is held by cable ties. Just tie the ESC to this. You can put the ESC in the body if you prefer, or hold it on top...

Remember to scale the fexihinges and bumpers by the same proportion if you do. I recommend that you load these into Tinkercad, measure your leg in several places, and make similarly sized objects in Tinkercad to see if they fit. There is also a...

Another sealing kit for Karcher ferrets that you will find here: https://www.thingiverse.com/thing:6496753 allows you to clean waste water or toilet pipes through their inspection holes without risk of return of water towards the operator, especially...

For kids with ADHD, autism, or those who just learn differently, a spinner can be a discrete, quiet means of staying on task by occupying their hands. Incorporated into an IEP, they can be exceedingly helpful. After designing a couple of...

By using this insert, obviously the interior height of the Bottom drawer is reduced. ###Measurements The interior of this drawer is approximately D 139mm x W 93mm x H 10 mm (5.5" x 3.6" x 0.4") ** I did not make the insert go all the way...

The original design came from Flower Mosaic by Yuyuy75 - Thingiverse.  I assembled the mosaic and then varied the height of the flowers so I could print it as a color print. ...Varying the height of the flowers also gave depth to the...

By using any of these files you are assuming the risks. I have used this with a green gas 40mm grenade I got from Evike with no issues (yet). These are my changes to Steve Hazes' m203 launcher. I am calling it version 2 since i want to...

If you have issues print it by itself at 8-10mm/s on a raft (0.3 air gap) should do the trick. (The bracket can be a little chewed up and still work). The pumpkin_helmet and Roller_Skates I've printed in PETG and were able to "snap" the head and...

For kids with ADHD, autism, or those who just learn differently, a spinner can be a discrete, quiet means of staying on task by occupying their hands. Incorporated into an IEP, they can be exceedingly helpful. After designing a couple of...

Off-the-ear headphones using these BMR drivers inspired by the Index headset. Here is the link to that project: https://www.thingiverse.com/thing:6402165RAGESAQ is also working with sctanf on an index strap adapter for the Big Screen Beyond along...

I wanted to print this awesome design by HexiBase on my Ender 3 but the two halves were too big to fit on the build plate so I split each one into two smaller sections. The two sections are joined together via a tongue and groove arrangement, making...

Lengthwise, the bumper should extend beyond the wing by about 0.5 mm on each side. This will prevent the sides of the wing from contacting the case. (4) Insert switches and keycaps into plate and PCB. (5) Clip the gasket wings onto the plate (not the...

Adding more holes to the outer diameter, for securing the filament during storage, was also greatly needed, in my opinion! TagsWith Bambu Labs selling alot of its filament without spools, I figured it'd be nice to have a way to distinguish the...

Please be noted: This file is distributed under the CreativeCommons Attribution-NonCommercial-ShareAlike 4.0 International (CC BY-NC-SA 4.0). You are free to: Share — copy and redistribute the material in any medium or format Adapt — remix,...

Automotive body filler, followed by high fill primer, & wet sanding were used to smooth the hull prior to being painted. Prop shaft The hole for the prop shaft may need to be carefully drilled out to fit the stuffing tube. Test fit with propellor...

If you wish, you can even keep the connector on the tool-head-side slightly loose by using soft rubber washers on the proper side. **Base Part** Connect all required cables to the not-powered(!) board, arrange them, tie them together temporarily...

By wiring the microswitch that is inserted intomagswitch in series to the trigger, you prevent the ETU++ from firing the gearbox while a mag is not inserted. (Or the microswitch is not pressed, more accurately.)</li><li>The sector gear switch is a...

It must be supported by the text you selected though. (e.g. Bangers does not support it)</li><li>The font. Nice is e.g.: "Orbitron", "Bangers" or "Luckiest Guy".</li><li>Each lines font size individually.</li><li>The distance between the...

The Light Guide Panel (LGP) diffuses the light emitted by the LEDs which surround it. The mirror layer, reflects any light heading out the back of the panel. Whilst the opaque layer diffuses the light making it look like a solid light source.</p>...

Edit: I was able to successfully hold a 1kg apparatus with the simplest locking method and by applying a more complex method of locking I was able to hold roughly 2.5 Kg or 5Ib with a force in the downward direction, (I do acknowledge that the...

As players continue to explore the world of Warhammer, they discover new characters, creatures, and storylines that are brought to life by the miniatures. ...Each one offers a glimpse into the rich history and lore of the game, inviting players to...

Whereas final version is 70mm wide and can be used with standard 4mm tubing or any fitting PC4-M6 with 10 mm spanner size. FINAL VERSION PARTS: There are two versions of SLOTS, version for normal 4mm tube and version for fitting PC4-M6. There are 3...

I won't be including instructions, as henryarnold provides a great PDF to follow already (and I also think that by looking at the photos and complete assembly file I've included, the construction is quite self-explanatory. To keep the servo wire out...

8 – Encaixar com cuidado a peça “Alidade_Inferior” com a peça “Base_Nivelante_Superior” ________________________________ en Project developed by the Technical Surveying Course at IFSC-Florianópolis. Used for teaching topography, angle measurement...

Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 300 Infill: 15 Filament: Any Any Any Notes: I shaved a ton of time off printing by reducing my tops/bottoms to 2 layers. You can see the infill through this,...

ALSO: if you like the "chonky" connectors in this kit, I have a complete set of these heavy-duty upgraded GoPro-style connectors here on Thingiverse: https://www.thingiverse.com/thing:5593105 UPDATED (v02): I came across JuanAto's GoPro adjustable...

So, the 3rd axle is driven by the 2nd axle. No need to mount a second motor/transmission! Simply get a pinion gear set and the two bearings that the pinion goes through. Then, get longer bolts to hold the cover on. The bolt holes go all the way...