machine vision camera mount 3d models

(I used bodies instead of components to avoid model breakage in case of major size change.) Required Parts list and where I got them: 1X 2032 battery holders: https://www.amazon.ca/gp/product/B08SQRSTJ4 1X rechargeable LIR2032:...

The tolerances on these can be somewhat tight, but they came out beautifully on my Bambu X1C.Model specific notes follow:cards_box_1.stl, cards_box_2.stl - Print one of each. You can add color on layer 4 or 5 (depending on line height) to make the...

Really like the wheel from TheSloppyApprentice's Watermill and was looking for ways to hold it besides that large frame in the source.So I could make it stand in a bassin or hang under some opening where water is dropping off.So here are 2...

i started with using an other Model as base and didn't check the dimensions 2. i realized my mistake to late XD 3. if i change the scale i would have to split in 3 parts because it would to long for the most Printers 4. i'm to...

[Medium Sized Model - 25mm Base] [Presupported with LYS files in 32mm & 75mm Scale] Once a renowned mercenary and officer within the Golden Griffins, Lydia spilt rivers of blood during her time among them on the front lines of the Liturium War. When...

This is a remix of my previous models: Modular Wahoo Board Remix Modular Wahoo Board Remix Case In this new version, I have opted for a singular base with holes for inserts for the "home" space to be swapped between the traditional placement and my...

Presupported in 32mm and 75mm scale [Medium Model Size] [Statblock included in our 5E Campaign: Divine Awakening]   The third child of Tharador, Renmaeth is the custodian of his body, the continent of Tharador. In the Age of Creation she shaped the...

Some of the models are difficult to hand-launched and should be tested with a 1/16" rubber band instead. A slight elevator-up reflex is required for flight. This is accomplished by latching the elevons up on the relex tabs on the aft end of the...

Add one if you have adhesion problems.Dimensions and Part NumberingYou find models for many combinations of heights and depths. The heights are in the range 35mm – 100mm and the depths are in the range 80mm – 190mm.</p><p>These numbers are included...

### Bridge style cards (58mm x 88mm) * `codeandmake.com_Quick_Draw_Card_Dispenser_v1.0_58x88_Single_Open.stl` * `codeandmake.com_Quick_Draw_Card_Dispenser_v1.0_58x88_Single_Covered.stl` *...

I always use a 4-5mm brim around such big models. You may need to turn off the skirt line then.</p><p>The 8 holders inside were printed with 100% infill, just to be sure that they were stable enough. You will need some screws, washers and nuts as...

Also also: if you get sick of chasing dice when they fire out of the bottom of the dice tower at high speed and scatter over the edge of the table, I would suggest you head over to [**domino6713's dice tower courtyard...

...More importantly, Thingiverse hasn't run their customizer queue since Jul 10, 2020 so until they fix that issue, you will have to install and run OpenSCAD (free software) on your own computer to process the code to create your own customized models.

The sourced parts needed are the same than for a MyRCCar OBTS Chassis, so you can use them in all models by now. This means that you can reuse existing parts from other projects, making it easier and more cost-effective to build this chassis. If i...

Reference photos http://ww2german.com/flu1694.html Reference data https://archive.org/details/Tm9-1901/page/n89/mode/2up https://bulletpicker.com/pdf/TM%209-1300-203,%20Artillery%20Ammunition.pdf#page=262 You can edit this model here...

idk what slicer or print settings were used on the original print, but I had to redo the entire geometry of that area to get it to print right without disturbing the bevel of the rest of that model. Unfortunately, given I don't have the original...

For your Rubik's cube to keep the fluidity of its movements, it is necessary that the dimensions of the model are reproduced very precisely, and that your board can allow a first layer of 0.1 mm... Usually to deal with defects in the horizontality...

(I have included a model with logo, and one without)Assembly Instructions:Print the box and two clipsInsert bowtie shaped post on clip in to corresponding hole on box, then rotate until the push-clip lines up with the hole.Push the push-clip in to...

It's corrected in the download-model.I know, this LCD knob is completely over-engineered and basically totally nonsense. But it was fun to design it and bring it to work for the LCD knobs contest.Triggered by verny's Cardan Joint Knob I thought I...

Don't use it for rendering or model generation. (see Reducer picture) PRINTING NOTE Print at 100% infill. Try and print standing vertically, if possible so that scaffolding may be omitted on the inside. These connectors are specifically designed...

this model the reason I like it better is because it locks into place then you just press the button and it works so nicer better than the others hear that you just hold it in with pressure. Arduino program settings this is all new to me I...

Creality slicer use edit, multiply selected models. PrusaSlicer use cut and past. I'm sure it's possible in other slicing software too. I would recommend printing a few extra as you may damage the edge on a few when inserting them. Assembly: ...

My prototype box had a problem in which the combination could be guessed by feel due to the slack in the model. This problem was fixed with a number of features that make guessing the combination by feel very difficult. As an additional precaution, I...

I could not find caps / hoders which suited my project, starting from inspiration of certain models existing in AA, I made a design under fusion 360 which corresponds in the size of integration, as well as the possibility of making spot welding. ...

Trim/Cut plastic flowers from a dollar store. Modified from this model: https://www.thingiverse.com/thing:3666273 Photo frame with a sliding/rotating cover. Slightly recessed oval of 40mm wide by 55mm tall to attach a 2D printed image/photo. Three to...

Cursed Immortality Season 2 - (2/4) The Umbratouched - Curse of Vengeance   Description Save money on this complete December Bundle, The Umbratouched, Curse of Vengeance, which contains all the models from the December release! These models come...

You can find a similar model at Amazon, the "MakerHawk USB Multimeter USB Voltmeter Ammeter Load Tester USB Voltage Current PD Battery Power Capacity Charger Digital Type C Meter Tester Color LCD Display Cable Resistance QC2.0/3.0/4.0 MTK " (lol) -...

Cap for benq projector lenses, designed for the mx660 model. It fits perfectly. On the outside it has the logo of benq and on the inside that of ho-kago tea time (musical group from the anime k-on). This projector did not have the cover when I took...

WORK IN PROGRESS Modeled off of reference pictures, many dimensions are guesses. This is intended to be a NON-Firing, but bolt operable, replica. can be printed entirely in PLA (if possible, the charging handle and magazine spring is better...

I have completed assembly and everything works so this addresses some of my main wants for this awesome model. I am also going to include the full parts kit here (the originals I used also), so everything you need is in this one thing saving any...