mars planet model

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_shape = 5 custom_bottom_port_corner_radius = 5 custom_back_camera_y_size = 20 printer_tolerance = 0.4 stencil_pattern_line_thickness = 30...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...

Remix of the amazing design of Lmaker.Added a part to be able to compare/finetune the Z-axis (offset) as well.This is a 10-15min print to make life easier when calibrating the X, Y, and Z-axis of (independent) dual extruder 3D...

As far as assembly is concerned, it's all pretty self-explanatory when you see the models, but here are a few tricks: Use as little wire as possible, but make sure you use good wire. The wires run from the grip and back, across the side of the...

If you want to shoot really fast you need also SIL Ammo Clip (Speed loader):https://cults3d.com/en/3d-model/various/sil-ammo-clip-speed-loader-for-sil-hybrid-repeating-bow Aiming is carried out using a laser sight (up to 15-20 m distance) or red dot...

... differences. As always please share any thoughts or feedback for further discussion and help each other move forward in design solutions, modifications for use on 3d printers like this model. ...These files were originally made with Tinkercad too.

... 3D model created using SketchUp Make (free software). I also tried 45 degrees, but the fan's thickness made it touch the desk surface below, so it had to be skooted up to the high end of the stand... thus the cooling effect would be diminished.

Any longer and you'll have to either modify the model or hold it steady by hand while screwing in the first few mms until the guide grooves engage. Any shorter and you'll lose variable length and have to use a tighter initial state for the...

  Walmart also has a good deal on a 4 Pack of the same filters HERE.The fan is a Black & Decker 9in Mini Box Fan, Model BFB09W.CostAt the time of writing this the total cost is the same for each of the 3 versions as the different sized filters are...

Some overhang areas in the inside don't bridge well, so you'll need to do some trimming / post-processing.Updated 5/2/2021:I added aluminum foil tape (HVAC duct tape, buy at any home/hardware store) for 3 reasons:serve as heat spreader so that the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 pattern_element_rotation = 0 custom_top_port_corner_resolution = 8 custom_right_port_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_x_position = 20 custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_bottom_fillet_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

All nuts used are M3 squares unless otherwise stated.The +1mm fan duct is for use with longer non-standard m6 nozzlesUse the following commands to use with stock Prusa firmware: M92 E690, M500You may need to adjust the extruder motor current using...

This is demo model meant to portray the scale and detail of the helmet itselfFor the full separated files you can find them hereaguilarworkshop.com/product-page/scout-helmet-w-attachments Major FeaturesMagnetic AssemblyThis helmet is comprised of...

Check out the build here: https://www.aheadrc.com/custom-builds Also check out the C23 “Workhorse” truck body here: https://cults3d.com/en/3d-model/game/crawler-c23-workhorse The flatbed comes in many options and details, including some bonuses. not...

... that is about 1/4"/5mm in the front center due to the belt tensioning clip bumping into the blower. Unless you like that kind of centrifugal blower fan on belt tensioning clip action, I recommend not to drag the models dead center to the front.

I added the resistor, pot, and a switch to the power supply control box, then modeled and printed a knob for the potentiometer to hide the apprentice marks visible around where I put the pot through. Should fit any potentiometer with a 6mm shaft and...

It was just hard to get some of the screws in it so I had to manually remove the parts this model has removed for you. Make sure is you use screws to hold the bearings tight that the lowest ones have low profile heads or they will be lower than the...

Stereographic Projection based on the excellent work shared here: https://jasmcole.com/2014/11/01/stereographic-lampshades/#more-650 I used Blender's "Solidify" modifier to add various thicknesses to this model for printing. I recommend printing one...

    Here are some key words copied from one of these advertisements if you are having trouble:PRINTINGThis model is for someone who enjoys the process of printing,  It is easy to print but there are nuts to be inserted  in both the main body and the...

Except for the Sunlu mount plate just lay the models flat. The Sunlu mount plate I printed standing upright - even without support (although some minor bridging is needed, but that was no problem)</p><p>As mentioned above, the hygrometers are...

Some special thanks to Alessandro Virdis for the belts lock model provided. Every single piece made this a beautiful work of different minds ;) It is a 3D printer with 300x300x300 mm printing area, powered by a Lerdge-S with Cr-2020 or Duplicator 6...

(Not required for revision 2) Scaling: The model as is in the STLs will accommodate most types of earbuds, however it can be scaled down as much as 30-35% for smaller sets. If you use earbuds with an inline control, such as the ones shown in the...

The color thicknesses and the width of the outline stripes on this test print match the stripes on this case and future cases I upload will probably use similar...

You can get the servo here: http://www.banggood.com/3_7g-Micro-Mini-Servo-For-RC-Model-p-77696.html The battery tray is at: http://www.thingiverse.com/thing:1289398. I have also included the battery tray files here. Make sure you print out the...

Eyelet diameter is 7mm (little over ¼").Obviously not suitable for safety relevant applications.Changelog2022-03-15v3complete redesign with smaller dimensions, shorter screw (M3x8mm) and additional clamp only variant2022-03-10v2easier assembly and...

We are presenting a new wind turbine device, that is easy to 3d print, it can be made handcraft once it is viewed it components and how they get assembled in a very easy and intuitive view, This system have several pending patents and the device...

;-) How did I end up with two of these devices? At first I bought the 2TB version and wanted to replace the HDD with a 5TB model. I tried several things, but nothing worked. With vaccation ahead, I ordered a second device with 3TB. The electronics of...