mecha models

* Select the model you want to print based on your printer's nozzle diameter, paying special attention to whatever preview you have available in your slicer. You want one perimiter shell with a tiny bit of squigly filament in between shells * The...

The pilings for this model are slightly long at the bottom as they were designed for the display demo table where they would be sunk about 5mm into the baseboard substrate to firmly fix them in place – so if you are planning to use them as free...

... the strip about centered under the nozzle I knew it was pretty good. I have thought about adjusting the model to match that, but haven't yet out of laziness but also concern that some blowers may behave a bit different. Category: 3D Printer Parts

The board acts as a cover.AdIf you wanna top up your experience, you can print one of my other models, the dice tower for two dices. The colors fit perfectly to the tiles and you never accidentally use the wrong dice for the wrong purpose. ...<a...

As I'm new to parametric modeling, this solution was done without adhering to full parametric techniques. I'm still learning. The KeyAll HV has two mounting holes, which left 2 open feet for other uses. One foot was left unused, and the other to...

(Not required for revision 2) Scaling: The model as is in the STLs will accommodate most types of earbuds, however it can be scaled down as much as 30-35% for smaller sets. If you use earbuds with an inline control, such as the ones shown in the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

Constant testing and printing are underway with mods on nearly every model, wasting over 300 feet of filament in the process. I'd appreciate support for my project as it's not intended for non-3D users but rather for those who want to quickly build a...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 40 printer_tolerance = 0.4...

**Just make sure they are all the same voltage and be very carefully** - **3S BMS 20A** - I used the HX-3S-FL20 REV2.2 Probably they are more models similar to this, this was the name I found. This is for controlling the charge and discharge of the...

;-) How did I end up with two of these devices? At first I bought the 2TB version and wanted to replace the HDD with a 5TB model. I tried several things, but nothing worked. With vaccation ahead, I ordered a second device with 3TB. The electronics of...

It Lets You See Your Model Being Built and Doesn't Obscure View. Why Make Yet Another Cooler? Cooling Plastic Just After Its Been Extruded Is Essential on FDM Printers and There Is a Lot of Choice for Cooling on the Makerbot Clones. I Tried All of...

Presupported in 32mm and 75mm scale [Medium Model Size] [Statblock included in our 5E Campaign: Divine Awakening] The last child of Minera to rise from the ocean depths as a great landmass. Tharador is the smallest of all continents and most meager...

give us the good bits lol...). Searching Thingiverse I found lots of Koppla mounts, but they all hooked the ends, nothing used the built in track mount, so I modeled the powerbar, then got to work... I initially thought of building it based on the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_top_port_corner_resolution = 8 custom_back_camera_x_position = 0...

Note: The X axis part is for the current model of the Geeetech I3 Pro printer that uses a metal plate on the X axis to support the linear bearings and extruder holder. When I was assembling my Geeetech I3 Pro C printer, I was struck by the fact...

Presupported in 32mm and 75mm scale [Medium Model Size] [Statblock included in our 5E Campaign: Divine Awakening]   The third child of Tharador, Renmaeth is the custodian of his body, the continent of Tharador. In the Age of Creation she shaped the...

For now I have modelled two trailers:mk14 flatbed trailer for general loads, 10' and 20' ISO containers.mk17 tray-style trailer with hydraulic crane. Can carry 1x 10' ISO container, or general loads. Tray sides are removable.mk14 trailer can also be...

In 3d printing a RC Stearman model I needed an 11x5.5 prop. Instead of paying $3 for one I spent<i>thousands</i> of person-hours using high-expertise design skills to build this!</p><p>It's a<i>procedurally generated</i> propeller design...

This is the first 3-D model I have built from scratch and I was looking to get it done quickly. So, I kept it simple but did note that it wouldn't take much to add a few more amenities that would suit personal needs or desires. The router fits...

The model is amazingly easy to fly. https://www.youtube.com/watch?v=rsS5YetUQyA The video quality is less good - this time I had to film myself. There are two hull versions. The longer version (lv) is the one shown in the picture and video. But...

Details and models may change as I continually improve it. Please see the pictures for individual printing instructions. If the spur gear for the table binds when rotating the table, loosen the stepper bolts, push the stepper inwards, and tighten....

A wrench is used to unscrew the end caps for relamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap. 7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

THIS WILL NOT WORK WITH THE HID GOLIGHT SPOTLIGHTS (GL-3XXXH-X models) The small size and wide input voltage range of this unit make it ideal for operating Larson Electronics LED light bars, Golights and other equipment that requires 12VDC current...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 40 printer_tolerance = 0.4...

Then, I saw it mentioned by a popular modeller on his YouTube channel, and over the next year, the number of downloads went up enormously. So, it seems like it's time to make some improvements from the original Version 1. DESIGN NOTES For the V1...

... tolerances must be around 2 tenths of a mm, it is not essential to use CNC systems. The pieces can be easily made by any turner or by a modeling enthusiast and their cost is quite acceptable. ... Criticisms, suggestions and changes are welcome!

Not a problem with a well-tuned MK3S+.&nbsp; &nbsp; The box was printed usingFilament &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;...

Worth note is the design has modeled threads or you could use inserts (see more here:...

THIS WILL NOT WORK WITH THE HID GOLIGHT SPOTLIGHTS (GL-3XXXH-X models). If you purchase this transformer with any of our Larson Electronics lights, we will make sure that the connectors are a match.Features: The DCP-25-DP 256 watt converter features...