mining rig 3d models

... <font size="+1">^Like</font> button** and turn that heart red <img src="https://cdn.thingiverse.com/site/assets/like-button-liked.svg">.                                                                 

It's remained undeveloped probably because it was originally registered as a mining claim by wily old man Lyman Truckenmiller and he built seven houses on the property (without permits) and rented these out for at least 30 years. Lyman also dug...

Make sure these are snug; mine came out wobbly and required further reinforcement (details TBD). For each side, insert plexiglass and attach the respective bottom braces - #2, #8, #9, &amp; #16. Start from the front and rotate around; you'll need to...

I heat mine on a silicone cooking mat, in a toaster oven, 15 to 20 minutes (more 20 minutes), at 100 to 120 degrees Celsius (110 is good). Once the process is done, I carefully take the part out of the oven and let it cool down for an hour before...

I used a cotton facial pad and some Kapton tape for mine and it's doing fine. 6x M3x12 bolts for the barbells 6x 10mm x 1mm washers for the barbells 8x M3 nuts (2 for the hot end lock, 6 for the barbells) 2x M3x16 bolts for the hot end lock (you...

I am using the Asus Tinkerboard inside mine: https://www.asus.com/us/Single-Board-Computer/Tinker-Board/ Powerful board that fits where an RPi3 fits! Inside this the screen bezel is changed to hold the new LCD unit and the Pi has been moved to the...

therefore I've made it public. Print SettingsPrinter Brand: UltimakerPrinter: Ultimaker 2Rafts: YesSupports: YesResolution: 0.2Infill: 15%Notes:All parts fit within a 200x200x200 print volume, and I'm sure you can scale it larger, but probably not...

Or just work it out without my files.Pull the pins out of the battery connector and swap them around if they need it, mine needed it, and if you get it wrong it will fry your controller. Red to the pin on the board near the +. Only you are sure you...

If your "normal" Nanos are like mine, I needed to install different driver for my windows but also select the (old) bootloader in the arduino IDE. The same way, i felt the USB port where you connect it to the computer must have enough "Amps" to...

I only had to adjust mine slightly so it hopefully is not a big deal, but may be worth checking before assembly. Assembly (see pics below): First install the Dupont connectors on the 2 wires attached to the LCD Voltmeters. You should leave about...

Also, I would not recommend doing this mod without also having some compatible corner braces, like mine (https://www.thingiverse.com/thing:2474583), that will transfer twisting moments on the uprights into the horizontals, because otherwise I think...

So my next thought was a dual barndoor hardware rig, one on each side of the floating gantry. This seemed fairly costly though. And then it hit me, closet sliding door hardware is basically the same, but is much cheaper and comes in a decent...

The extreme durability, universal voltage capabilities, and LED longevity make this LED flood lighting system an ideal fit for frac pads, rigs, offshore, and any application that requires a Class 1 Division 1 pole top light fixture.Mounting Notes:...

## My build on the test rig i used the following gear : - [FPVCycle 25mm 1880 Kv motors](https://fpvcycle.com/products/fpvcycle-5-motor-choose-options) (do you a treat and get some of those amazing motors) - Gemfan 5226 props - AIKON mini stack (F7...

The extreme durability, universal voltage capabilities, and LED longevity make this LED flood lighting system an ideal fit for frac pads, rigs, offshore, and any application that requires a Class I Division 1 pole top light fixture.Mounting Notes:...

ABOUT THIS 3D MODELIn the spectacular post-apocalyptic setting of Mad Max: Fury Road, the showcase of Immortan Joe's power introduced a plethora of fantastic custom-built vehicles, such as the monstrous War Rig. As if antagonising it, the Gigahorse...

Sorry that this bug got through - I think my development chip had at one time the correct details saved, and when I edited the code and accidentally broke the wifi config saving, I didn't realise, as mine still had a valid saved copy. It should...

ALSO - DO NOT LEAVE THIS STUFF IN YOUR CAR; I LEFT MINE IN THE CAR FOR 10 MINUTES ON A HOT DAY AND RETURNED TO A WARPED MESS. Thermoforming can also resize your snaps and bar hole sizes so play cautiously and experiment with extra parts. Stuff...

 This is exactly how mine is made and it works well, HOWEVER, if I did this again, I’d make the Front/Back and Top panels .25” wider to give a little more clearance, so I’d recommend 13.94” instead of 13.69” wide for the Front/Back and 13.32" instead...

(I use +0.1 to print mine) Use only 2 walls to print the piece.If you are using a different slicer, look for the equivalent settings that improve small hole size accuracy.Print a border piece and a second board piece. Verify they fit together well. A...

although i do notice when holding mine, (left handed) that i can hit the buttons with my knuckles fairly easy, so use your discretion when choosing. 4 Handle: heavy modification for large lighted arcade buttons. 5 Pipe Socket : larger hole for...

although i do notice when holding mine, (left handed) that i can hit the buttons with my knuckles fairly easy, so use your discretion when choosing.4 Handle: heavy modification for large lighted arcade buttons. v2 has the holes fixed per Jdigi78. the...

A DXF file is attached that you can have laser cut or CNC'd - I had mine cut in 5mm thick 304 stainless steel - overkill, but it really shifts the weight to the bottom of the chassis, strengthens the frame, and *maybe* even marginally improves print...

the O-ring shape is impossible to find outside of Macmaster Carr, Casting RTV molds coming soon!)...

&nbsp;When I re-print mine, I'm planning to remove that gap, as I think the paddles could be more durable without that gap. &nbsp;A rock or something has ripped a corner off of one of my paddles - maybe without the gap that wouldn't have happened, or...

This light is designed for heavy duty use in demanding conditions including emergency services, mining, construction, marine, and industrial operations where durability and reliability is critical.This portable LED light is comprised of an adjustable...

You can also print the shapes, then cut the stencils by hand.• Cricut vinal, and long matt if you can, if not you might have to cut the stencil into smaller sections to fit it.• Dremel with engraving bit or similar tool for etching/scratching the...

Apparently mine featured an USB interface, hence flashing WLED was straight forward. As GPIOs usually are limited to 20 mA I needed to PWM these pins (described above). As these are just prototypes I never got around redesigning the bottom plate. If...

Some (better than mine) microsoldering skills are required, if you're using an SBUS receiver you need to run the RC jumper accordingly. WiFi network may be disabled permanently with following CLI commands: set pinio_config=1,1,1,1 set...

The second possible troublemaker is the space between letters; check that there are no holes, and adjust fill angle, or extrusion widths, or detect thin walls, etc., to fix any; don't rely much on bridging, as it will be too high to show in the first...