modelling madness

...You can also save money if you can find a local shop that sells a retina display replacement, But be sure it's the right model. All in all you could maybe save 50~100$ depending on the parts you already own and your own creativity in sourcing parts.

This meant adding three holes for screws, and I also added flanges on the bottom in an attempt to mount the fan shroud I modified for my model cooling fan shroud. I left the sensor port alone for now - I may or may not try using the cooling fan...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_back_camera_x_position = 0 custom_top_port_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_x_position = 20 custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_bottom_fillet_resolution = 8...

... I'd use WS2811, 12V strips in either 60 LED's per meter or 96 LED's per meter. For arches the 60 LED / meter is probably the sweet spot. Feel free to suggest improvements in the comments section. ToDo: Create xLights model and add to download.

...All "mandatory" supports are already in the model. This piece on the photos was accidentally done with 0.15mm layer height and it turned out fine, although I intended to print it with 0.08mm height. Everything from 0.1mm and below should be alright.

Create a 3-D model of a train car. 4. Compare and contrast which shapes should be placed together to create certain objects. Audiences: This lesson is designed for high school students in geometry. Subjects: math, art, science Standards:...

http://creativecommons.org/licenses/by-nd/3.0/ # Summary [#3DBenchy](http://3dbenchy.com) is a 3D model designed by us at [CreativeTools](http://creativetools.se) specifically for testing and benchmarking 3D printers. It is a small recognisable...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 30 printer_tolerance = 0.35...

So for example file "C-FenderWasher_x_2" needs you to print 2 of these, but the file only has 1 fender washer model in it. - The threads in the part "B-Clamp_x_2" are designed to take 1/4"-20 machine screws. I used1/4"-20 x 3/4 in. Zinc-Plated...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...

OK, this isn't a model but rather a gcode script to facilitate automated cold pulls to clear out your nozzle. I use it all the time on my Ender 3 and thought others might get some good use from it as well. **What is a cold pull?** A cold pull is...

*** Yet another pose here: https://www.thingiverse.com/thing:4672484 *** Subscribe Now! A very good model from Velrock. Time-lapse print video : https://youtu.be/4lXVR1HwAAU If you are looking for Baby Yoda in this print: ...

If you don't know how to mirror a model in your slicer, please research this first or you risk wasting a bunch of filament. Follow the same pattern if you print on a larger printer. Make sure to still print the "sliding supports" You should...

But don't hesitate to choose the one you prefer.The Raspberry Pi racks I designed are compatible with the Raspberry Pi 2B, 3B and 3B+ models. They should also be compatible with the 4B versions of Raspberry Pi, but I haven't been able to test them...

But the base design is a mix of: Ichibey's Sakura CoreCube Hbot modeling work Jetguy's lasercutter templates and electrical / extruder configuration DNewman's Sailfish programming for CoreXY gantries Credit should go to the above -- I'm just...

I have printed all of the parts and assembled a model which is shown. The "Dome" cover will fit over the Base Plate, and in turn a 1/2" piece of sprinkler pipe will fit over the tabs in the center of the Base Plate. The Mic Holder will fit over a Gen...

It will be a lot easier for me to fix a problem than for you to re-model a part. Designing my first blaster has generally been a fun experience, a bit more difficult than I thought it would be though! Stock mounts and magwells were the most...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_y_position = 0 stencil_drawing =...

The pilings for this model are 20mm - slightly shorter than for Huts 1 to 4. If you want an easier time of it, you could just print shorter independent pilings, so the huts are not raised so high and its just a single step up into them from ground...

In this case, I have proven that it is valid for several models of Epson projectors, which are the ones I like the most, seriously, I hate dlp projectors. They tire my eyes a lot and all of them, to a greater or lesser extent, create a rainbow...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 0 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_position = 0 custom_right_port_y_position = 0 custom_phone_thickness = 10 stencil_pattern_element_rotation = 0...

A wrench is used to unscrew the end caps for relamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap. 7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp...

This model is designed for pla/pet-g which does not shrink. 2) print in the orientation show in the pictures. While this does not give you 90° opposition for force vs layer lines, it does give you about 45° which is much better than 0° printing with...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 0 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

From the original set I only did not try to model the chain gears since the chain consists of quite small parts and would be difficult to print accurately enough. On the other hand, I added many different gears to the original ones (12T, 24T). ...

The models are properly oriented for printing, and like most of my prints no supports are needed. Included STEP Files 3D printing is all about making something new, unique, or customized. Therefore I always include the STEP files. You can use...

The models (keys and legends) are the same dimensions and should center at the exact same spot. It’s really difficult, and you will fail again and again, but the result is worth it (I think). You could also print the keys upright (with supports) and...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...