models walking

IntroductionMany designs like RC cars and trucks, lanterns, model houses, etc. would benefit if 3D printing could be used to create truly transparent window panes. But as you might know, FDM printing transparent filament per se does not result in...

Special credit goes to Orcy Wagh, who created the servo model over on Grabcad (https://grabcad.com/library/micro-linear-servo-right-1). What is different? In contrast to the BFPTouch, this thingy uses a nano sized linear servo to release / lock the...

All in all, I believe your satisfaction with this mask should be limited only by the skill with which you make it, and not by any features of the design.Hope I won’t see any more comments to this design base on general 3d print issues(rough surface,...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8 custom_top_port_corner_radius...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 pattern_element_overlap = 0 custom_top_port_x_position = -10 custom_bottom_outer_edge_chamfer_radius = .6...

License ------- The "Arduino Nano NeoPixel Ring Base" models (.stl) are licensed under the [CC BY](https://creativecommons.org/licenses/by/4.0/) license by [Code and Make](https://codeandmake.com/). The "Arduino Nano NeoPixel Ring Base" code...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_mirror = 0 stencil_drawing =...

 The switch is wired so it goes from Off to On with no sounds to On with sounds. ...

This is an enhanced print bed filament dryer based on Design Prototype Test's video on the topic seen here: https://youtu.be/H1DoJxY6v_U.  The air flow has to make a 90 degree turn at the top and bottom, so I used a velocity stack for the top...

If using liquid electrical tape, allow it to cure before continuing. Gluing Use a small amount of hot glue to attach the diffuser to the LED mount. Using To use, simply attach a 9v battery and insert the LED mount into the base, ensuring that the...

Buy me a coffee!https://paypal.me/SmartHelpatHome   *Buck-converter:Used in 3D printing to regulate 24V to 12V for example when using 12V fans or other electronics on an Ender 3 which is 24V native.More...

There were points where I’d get 0.4 and Edwin would be 0.5 with his ruler while using the same model. Chances are that we used a ruler that was slightly wider than what 1mm is in reality.</p><figure class="image image-style-align-center...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_resolution = 8 custom_right_port_corner_radius = 5 custom_back_camera_x_position = 0...

If in doubt refer to Mehdi for more demonstration material.I was basically trying to address two "issues" of my Anycubic Vyper:The PSU and Mainboard 24V fans are very loudI want to upgrade my Vyper with an OctoPrint/OctoPi setupSo here is my...

A wrench is used to unscrew the end caps for re-lamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap.7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

&nbsp;Foam card (if you're not already familiar with it) is a material used in the art world and in crafting or modelling situations, a layer of foam is sandwiched between 2 layers of card, the resulting material is incredibly strong and is generally...

Comments and suggestions are also very welcome.Update 2020-10-19 Kermi radiator mount clips now availableQuite a few new MultiClip Objects in the collection (link above).Update 2018-09-21 Updated the alignment helperNew: MultiClip Glue!Update...

Able to hold 1 stack of cards and 2 columns of hexes. --4-2-17-- Added player card 2.2, a little bit smaller on the separator pieces that come off the model, should be easier to fit in the box. --4-2-17-- Removed older hex and cards .stls and...

Extending the print head cable on this model is not unheard of, it is a common change made when upgrading this printer to a direct extruder. The portal cable (black) does not need to be extended, even for the extension kit for 50mm, as long as you...

Check out the Raspberry Pi 3B+ here: https://www.raspberrypi.org/products/raspberry-pi-3-model-b-plus/ The controls are simple but there's enough buttons for most games. D pad for direction control and 4 front buttons provide your basic SNES type...

A round-pole design makes the assembly easier to handle and transport compared to square-shaped models.A horizontal T-mount platform is provided at the top of the tower for mounting customer-provided equipment. The tripod features a rotatable head...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

This model involves many grams of material but also many hours of slicing, printing and overwatching your printer. I suggest you to print the main parts in 0.2mm layers if you don't want it to take forever :S and use something between 0.4 and 0.5 mm...

- You can find a somewhat more detailed list of supplies in my Instructable at https://www.instructables.com/Kissing-the-Frog-V20-Back-Horn-Bluetooth-Speaker-F/ Basically any combination will do (as long as the driver is 3.3" or smaller so it fits...

Load your Model into PrusaSlicer and assign both materials. Prusa provides a quite helpful database on their website on how to use all the features in their Slicer that are related to multi-material-printing. After changing the filament there is...

I increased the version numbers to reflect this, but if you already printed them you don't need to reprint because there were no actual changes to the models. - Added drop-in boxes to fill with cut-off 12in bamboo shish-kebab skewers, to allow for...

... one at a time by clicking Download each time. Or click Download once on the file Girl_Unicorn.rar ### My some other things: Category: 2D Art

A wrench is used to unscrew the end caps for relamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap. 7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

I made a CAD model, did some tests to see what would work and built this desk. It's called ‘Carl’s Desk', because the original was made for Carl.</strong></p><p><strong>This is a rebuild for the print tables contest, the 3D printed parts are now...

It is essentially based on my first design.If you don't have an AC Infinity T8 or don't want to spent 120 bucks on one just to disassemble it, check out this simpler and cheaper...