moses tabernacle model

The pictures and model views all show the right hand frame. Most of the parts print without supports except for the inside half of the spool, handle post and reel frame that require “supports on build plate only”. I also use 100% infill for all...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

Depending on how well your models adhere to the print bed, you may need a brim/shaft/skirt to increase adhesion. In principle, it should be printable with any 3d printer, as I printed mine with my old Anycubic, which was about to break down...

Works with the regular rectangular heat sinks or the Waveshare heat sink.Two different styles of ventilation openingsSTEP files available for easy remixingThis remix does not currently have an option to mount a fan inside the enclosurePowering the...

Specifically, the mouth utilizes inexact measurements, and inconsistencies in source models from the 3D printing process made it difficult to gain a good measurement. On the sketch, we measured the mouth to be 1.20cm from the side of the constraint...

The shoe lace is optional but it's a good way to secure the handle from unfolding when you don't use it.Print SettingsDon't rotate the models when placing them in your slicer. I have placed the parts in the best orientation possible with surface...

You can use other sized bolts (M3 or M4) files are uploaded for adjustments, I can and will upload different sized models.* *OPTIONAL PARTS* 3x WASHERS (desired size) 3x Nyloc Nuts (desired size) #HOW TO PRINT During the design process I accidently...

You only have to rotate the model so the gear is at the top. I recommend turning off the supports because it's extremely complicated to remove them.&nbsp;<strong>You have to print two of these...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_mirror = 0 stencil_drawing =...

Please check the images to see what it is included in this kit.This set contains: - Northmen Berserkers (12)- Berserker Skinchangers (4 + 4)- Skadi Ulfhedinn – Demigoddess of the Hunt- Gauldurbjorn – Skadi Companion- Wodan the Allseer- Eldormr - the...

You may need to adjust your printer, sand the chamber a little, or apply some force, as the parts were modeled to fit with ZERO clearance, to assure the best possible bond when using superglue. Just apply superglue to the syringe holder anywhere...

Microstepping is not saved in the EEPROM, that's why this needs to be in your startup gcode. CREDITS : Prusa R4 extruder : https://github.com/prusa3d/Original-Prusa-i3/tree/MK3S CAD model for Bondtech gears :...

This has taken several months to work out the kinks, but I think I have a good working model now. However, here are a few things to note: Prior to any assembling of any of the parts, I have found it is best to pre-thread all of the screw holes...

2022-04-14 I started to create a new base that could use threaded inserts and quickly realised the base models had become quite complicated due to the iterative design process, so I went back to basics and recreated them. The new housing mechanism is...

&nbsp;READ BEFORE PRINTING!This is a non-commercial print, this means you are not allowed to sell files or prints of this model.______________________________________________________________________________________What is this?This is my fifth...

This left us with our final model of our ghost clips.&nbsp;Assembly Instructions:Create center rectangle centered on the origin&nbsp;Set as construction geometry&nbsp;Add smart dimensions to constraint box&nbsp;Add construction lines for where arcs...

# Introduction This is a remix of the Ender 3 HallON v3 Installation kit to fit a Micro Swiss Direct Drive set-up (recent models with additional screw holes on the left. Because I noticed that the hold of the sensor in the adapter gets loose after...

This has taken several months to work out the kinks, but I think I have a good working model now. However, here are a few things to note: Prior to any assembling of any of the parts, I have found it is best to pre-thread all of the screw holes...

The design is made for an E12 bulb socket, but the "Bulb Holder Mount.stl" part could be easily modified in modeling software or simply by drilling new holes to line up with a bulb socket of your choosing. I am considering using an E12 smart bulb to...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_corner_radius = 5 custom_left_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

UPDATE: The model has been printed & test fit. Like a freakin' glove. #caliperlove Inserting the letters requires a bit of finesse & just enough brute force not to break the R and X apart- just be patient & make sure to clear any wisps/stringing in...

# What you'll need This will work with any CH340 USB-serial chip I think, but the model here is for the CH340N for USBC. A picture of the exact chip is given. I ordered one from AliExpress for about $3, and one from eBay for about $6 (because it was...

This model is intended to be glued together using Gloop! Get your Gloop! here: </strong><a href="https://3dgloop.com/shop"><strong>https://3dgloop.com/shop</strong></a></p><p>Assembly made without using Gloop! may result in the need to prepare for...

As provided the enclosure is set up to accept a 9.7" 2048x1536 panel as used by some iPads - Model No: LP097QX1-SPC1 https://it.aliexpress.com/item/1005002113658592.html There is no reason why you couldn't use any alternate panel and suitable driver...

... There are also useful coat hangers and finger toys.Compliant mechanisms:In case you want to know more about compliant mechanisms, check out these models from BYU_CMR.

&nbsp;(Photoshop can also be used for creating the Bezier curves, but Inkscape is a freebie...)Retraced .svg image inserted into background in Fusion360 model file, zooming in &amp; out to make sure all line ends were actually connected (crucial!) -...

To connect this to the second hand holder disc, I bought a plastic tube of 1mm inner diameter from a modeling shop. I pinched one side a bit to make it flatter. This seems to work, but maybe I will have to glue it on the pin. I didn't do so yet...

The VR Box comes with pads that may fit your need here. Even if my model provided screw holes and additional holes to fit the screwdriver through, I do not recommend using them. The pillars the screws were originally drilled in are most likely...

For the extruder I used from: https://www.thingiverse.com/thing:2735475/files cable-holder.stl https://www.thingiverse.com/download:4650325 extruder-cover.stl https://www.thingiverse.com/download:4650320 extruder-idler.stl...