multi tool knife leatherman wave 3d models

The original interior geometry from the Prusa filament sensor has been incorporated into this design, sourced from Prusa's models. The pinda is in the same location as on the original. The nozzle in this new design sits 10mm further forward along the...

As per my usual, each Zip file will contain the model un-based, based, and with supports. In order to keep files sizes down, I will no longer included the mirrored files for some of the linemen which you can easily do yourself in either the Chitubox...

Most parts do not need support and can be printed using the model orientation. BaseTopMotor and the Lid need “support on built plate only”. MotorMount needs to be rotated by 90 degree on the closed end (the one with the screw holes). In addition, it...

The first one was a box, with an RFID reader, that provided clues on its LCD screen and had a secret compartment that opened with a specific secret code. The second device was this Bocca della Verità with RFID in the mouth (it was a secret) provides...

The stock globe has a vent on the top and there are vents in the model to aid the convection cooling. Is it *really* needed, especially with the converter gone? Dunno so the optional rain cap comes with the caveat of possibly shortening diode...

The assembly is not complicated, for each configuration I put exploded photos, pay attention to the insertion of the brass threads, (there are 2 models you need both), and to the direction of insertion, those placed in the attachment of the guides,...

A wrench is used to unscrew the end caps for re-lamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap.7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

...I propose some activities to do programming this robot: First goal: Making it move The first and basic activity could be to program and model their movement, to find the correct position sequence for each leg for a forward run. First step: assembly.

 The switch is wired so it goes from Off to On with no sounds to On with sounds. ...

Four screws for every corner and 8 screws for every side.[blue] NO acrylic glass holder at the side where the hinge mechanisms are located!From this on the “Front” is where the hinges are.[green] At the location of the green circle you can drill a...

We are modelling the *BELT* tooth here, not the tooth on the pulley. Increasing the number will *decrease* the pulley tooth size. Increasing the tooth width will also scale proportionately the tooth depth, to maintain the shape of the tooth, and...

The design is a complete rework of my older oscillating fan model.It uses a common 130 size brushed hobby motor and incorporates an 18650 battery in its base for completely portable operation. Compared to the older design, the new version has...

rice or sand.Glue if the press fits are not tight enough Testing tolerancesStart by printing the models press_tolerance_test and rotation_tolerance_test from the folder Common parts.Press fit toleranceUse the press fit test to decide which press...

Or rather, it's a scale model of what that house looked like fifteen or twenty years ago. The wrecked version is closer to how it looks now that it's been abandoned for the better part of two decades. The tweakers have had a field day with this...

It deviates a bit of what I usually call an "sci-fi astronomical object", because it's an in-spacecraft transport vehicle. I made this model available in 4 scales. I left the model in "halves" that I consider the best way to print it, of course, with...

Model says 119mm, which would be close.???---------------------------------------------------------------------------------------------------------Printed Parts: Base:___________________Placeholder____________________This is the base of the...

Possibly by using simulations.Rails as a wholeSince my 3d printer is not big enough to fit 120cm ring on it (its bed is 210x250mm) I needed to split rails for printing and connect them afterwards. I decided on using M5 bolts and nuts.</p><figure...

Micro USB Breakout Amplifier 14 x M3.12 Plastite 2 x M4x45 Screws 2 x M4 Nylock Nuts 4 x M3x14 Screws 4 x M3 Nuts Dual USB Panel Mount Single USB Panel Mount 7" Capactive Touch Screen with 1024x600 Pixels or Pi Foundation Screen 800x480px Flat Flex...

I'm not telling you how to 3D print parts and clean it. You know it. BOM: '1. RPi 3A+ / Zero W /Zero W2 (and similar clones that have the same outline as Zero), microSD card, '2. Raspberry PICO working as keyboard martix USB HID device...

The servo spindle should be towards the middle of the robot.COGCut the servo horn with a pair of wire cutters so that it fits into the cogPush the servo Horn onto the cogMake sure the servo is at the minimum rotation position (turn it clockwise until...

I illuminate my RepRap 3D printer's control panel with it. The LEDs require a 12-volt power supply which can be supplied by the printer electronics (Rumba Board). Material: ABS, 3mm thick Nozzle: arcol.hu hotend v4.1.1, 0.35mm diameter Printer: DIY...

Potřebné vybaveníNotebook nebo tablet, programy Tinkercad a PrusaSlicer, 3D tiskárna.Nepovinné - krabička čtvercových rozměrů, tvrdý papír, pravítko, tužka a nůžky (viz postup).9. Potřebné soubory a dokumenty (seznam...

It appears to be a set of points in 3D space represented using an [Hull format](https://docs.python.org/3/library/pickle.html#pickling-hints). I will assume you'd like me to convert this into some kind of array. However, there are no "lines" or...

I also saw another model: https://www.aliexpress.com/item/4000497767128.html. I bought a pair of these with 9006 shape, for a Toyota which has projector type headlights. The light pattern seems ok and my eyes find them as bright as these 22000LM...

The objective is to not create bulky pieces of plastic that distract from the model with the exception of when it is necessary to do so, such as a lift system and a track splitter/track combiner, motor and battery mounts, etc. I will be adding a...

First, we need to make several models like this:First, we'll make our parody-homage "Stranger Things" logo in full solid and raised text for better display (we'll change it to POP before rendering the object). The Stranger Things logo has some...

I have to clarify that non feature shown in the model have a real correlation, the material there is orbiting in a thin flat disc around, and from 3 times the Schwarzschild radius beyond. The main brilliant ring is the photon ring, composed of...

Use this model to design your own attachments or print them to cover your unused attachment points. Accessory Pencil Bandolier I measured my collection of pens and pencils and found they were all around 10-10.8mm thick. The holes in this accessory...

Like most of the sci-fi and astronomical models of this scale, the topography is exaggerated to make it more visible. Something about the thumbnail image: I generate it using Blender, in which I painted the model, and illuminate the scene with two...

Customized QR and tag design for Thingiverse model #46884 using Customizer! ... Tag thickness: 3mm Corner radius: 10mm Round corners: Enabled Subtractive layers: 2 Tag width: 80mm Object type: Flat QR scale: 1.6x QR bottom left position: Origin...