nerf modulus stock 3d models

Print Settings Printer: monoprice mp select mini Rafts: Yes Supports: Yes Resolution: .1 to .15 Infill: 10-20% Notes: I upgraded to Nema 17 motor with .05 leadscrew so your resolution will be different with stock Mini. I would go with decent...

The more expensive ones (or larger pump kits) come with 1.5 inch tubing and shut offs to make this more manageable (if you buy them extra) but for the stock 1000 pump and 1.25 inch tubing you get on the entry pools (mine is the 15 foot 48 inch pool)...

Update Dec 1, 2021I've added step files for easy editing in case you want to make it fit your specific printer, Qidi tend to change their printers without notice from time to time.DescriptionThis is an automatic ribbon cable holder for QIDI X-Max, it...

I do not, however, love the stock buffer. I tried a bunch of things available, and for one or more reasons did not like them, and air buffering can be a pain even with a lot of room. Also, what is the point of printing directly from a drybox with...

Don't use the wires that come on the camera stock, the ATX03 has very nice silicone wires that are long enough to run all of the equipment (camera, receiver and VTX) if everything is planned out. 6. Spend a lot of time on wire management, there is...

The whole thing was printed on a stock Prusa Mini+ with a .4 nozzle.Photos IRLFully assembled it will look like...

 If you have the proper filament colors, no painting is needed.The assembled model is 220mm tall.Enjoy!...........................................................................................................**Print Instructions:**Supports:...

While installing the drag chain I recommend to remove the mesh stocking. It causes horrible noise when being in the chain. ### Credits (to the fellowship of drag chains) [YucA305](https://www.thingiverse.com/yuca305/designs) did a solid job with...

TPU Camera Mount The stock PLA camera mount that came with the frame wasn't printed with 100% infill or nearly enough shells, causing it to split in half immediately after I tried to install it. I simply replicated the design and printed it in TPU,...

It should be almost the same with the stock Anet firmware, and similar with Skynet3D (Marlin)\nWhen you have tuned your heater properly, the temperature will fluctuate by just plus/minus 0.5 - 1C and will be very stable.\nNotes\nActually try it...

However if your stock bumper mount just happens to be at the right length then there is no need for any customisation. Again, let us know if you need help designing it. Assembly instructions: View the link below to download the assembly instructions...

Updated 12/19/2021 (details at bottom of this summary) DISCLAIMER: My printer has been heavily modified and there may be things that won't work on a stock CR-10 or Tevo Tornado. Please plan ahead make sure you cover all your bases. This mod probably...

The stock wire in that conduit is for the 'safety switch' on that clear cover guard thing that everyone removes, and the tapping auto reverse micro switches, so i had 2 free wires that used to be for the safety switch already between the mill head...

I used an M5x35, and previously recommended a 30mm instead, however 30mm is a bit tight if your belt is reasonably taught with the stock mount, so it's better to use with a 35 unless you mind the end of the bolt poking out the nut head in front of...

To swap out the XY stage on a stock Makerbot, I usually had to: 1) Remove the 8 bolts holding the rod covers on the left side of the bot with a hex wrench and needlenose pliers to hold the nuts. 2) Remove the rod covers and slide the rods out. 3)...

This autocannon retains the hitting power and payload of the stock autocannon, but pays in range for it’s shortened length. In addition to these there are the support weapons that can be mounted to IFV-20-D and IFV-20-DL (though these are not...

The stock v-core 3 has a stainless steel linear rail on top of a black aluminum extrusion. That extrusion is really good at absorbing heat from the bed. The aluminum and steel expand at different rates and the bimetallic effect warps the...

This design replaces the stock X carriage bracket of a Anet A8 / AM8.The backplate features a mounting pattern for a BIQU H2 V2.0 extruder / hotend, using 4 attachment screws. A second part features attachment points for a 5051 blower fan, an...

Note: The project relies on "stock" LED mod already installed, mostly for holding cables in place and also integrates with the wiring for LEDs to save on space. It can be done stand-alone without LED strips as necessary. Note 2: I'm partial about...

My current printer is a Creality Ender 5 Plus that I am repairing at the present time and I - of course - not only have to install my new Meanwell RSP500-24 Power Supply, but I am also replacing the Bowden tube with a Capricorn, changing out the...

... I printed using Monoprice PLA+ with extruder temp of 200 and bed temp of 45. The initial layer is 210 and 50 to aid adhesion. I have the stock V2 hot end and a glass bed with buildtak on it. ... The chain requires 16 links for this implementation.

The original, stock, belt was too short for this configuration by an inch or two. The X carriage itself has holes designed to securely hold a metal NEMA 17 motor mount. These work well for mounting Titan extruders. There is no provision for mounting...

 A stock clamp might work but I didn't verify. Conclusion:The end….Actually, if you guys wanted a churched up version of this thing I can add some embossing to the design. ... Let me know in the comments if this is something that is...

Includes mounting for dual 30mm (stock E3D) fans or single 60mm. Recommend 60x10mm fan for reduced weight and size with increased airflow. Superlite carriage now included along with the original one. Superlite carriage comes with another 25% weight...

Advice Before You Start ================== Because the stock bolts strip easily, I suggest that before you start, you remove them one at a time and either snug them back but not too tight or -- better -- replace them with proper 3mm bolts. I had...

We are replacing them inside the power supply for a clean look plus the stock wires are not large enough to carry the current the printer will need. Then remove the PCB from the case so you can get to the bottom of it. With the bottom exposed start...

It is thicker than most caliper depth feet, but it still fits in the stock removable accessory compartment included in the case. I 3-D printed the foot on its side to minimize warping on the critical faces. This does make some supports necessary in...

http://creativecommons.org/licenses/by/3.0/ Hinges, Handles, Powersupply holder/bracket source: IKEA Lack Enclosure Creality Ender 3 Compilation by Woody1978 on Thingiverse: https://www.thingiverse.com/thing:3083358 Motherboard Case source:...

Book Collection: Stock your bookshelves with these beautifully detailed books and books on fantasy shelves. 4. Cozy Home Accents: Create inviting spaces with these intricately designed carpets in a range of colors, each featuring instance settings...

Fan ducts(several to choose from or print them all and test each one) Effectors(there are a few to choose from including stock style,E3DRV5/6 style and Delta style Frame parts(reinforcements and extrusion covers/fillers) LCD knob/back cover LED...