nerf shell 3d models

Three shells and 15% infill are used throughout. The design incorporates TPU parts, which require specific settings: extremely slow print speed, no retractions, significantly increased flow rate (+15%), and a 0.1mm layer height. Experience has shown...

A BIC pen was used for sizing, but the design works with every pen that I tested.PrintingNozzle: 0.4 mmLayer Height: 0.2 mmInfill: at least 15% (20% or more recommended)Vertical Shells: 3Top/Bottom Layers: 5Supports: NoYou'll need to print one top,...

The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.This model was tested with PLA material.To avoid printing problems, we recommend the following settings:ExtruderNozzle Diameter: 0.4 mmExtrusion...

Print Settings Printer Brand: RepRap Printer: P3 Steel MM Large Rafts: No Supports: Yes Resolution: Nozzle: 0.8 mm - Layer height: 0.3 mm - Shell thickness: 1.6 mm Infill: Fill Density: 35% Notes: The piece has been printed with PLA 1.75 filament...

The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.This model was tested with PLA material.To avoid printing problems, we recommend the following settings:ExtruderNozzle Diameter: 0.4 mmExtrusion...

We recommend some instructions for printing, divided into two Cura sets: INFILL: -Shell Tickness: 0.8 mm -Top/bottom Thickness: 0.8 mm -Infill overlap: 15% -Infill pattern: Grid Check infill top solid check infill bottom solid SUPPORT: -Support...

This has a nice little plastic shell and the pins are already attached to the leads. Technically, all you have to do is stick the right colored pins into the corresponding holes on the VB and controller, and you could use these with no modification...

I printed the parts with PETG (PLA will do just fine, but I like the neon green filament) using 0,2mm layer height, 3 top/bottom layers, 2-3 shells and 20% infill. The bearings should sit tight and hold everything together, but if you want you can...

The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.This model was tested with PLA material.To avoid printing problems, we recommend the following settings:ExtruderNozzle Diameter: 0.4 mmExtrusion...

Please note the following print settings: * Printer: Duplicator i3 Ultra * Rafts: No * Supports: No * Resolution: 0.2mm * Infill: 50% to 100% * Notes: Print using a 0.8mm shell thickness and orient the part as shown in the STL previews for maximum...

Perhaps you could experiment with the number of shells vs. infill and cut your time down drastically. The cone turned out a little thicker than I needed I think. Maybe you want to go into the design file and thin it some? Enjoy. UPDATE: I printed...

The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.This model was tested with PLA material.To avoid printing problems, we recommend the following settings:ExtruderNozzle Diameter: 0.4 mmExtrusion...

My Print Settings: Sliced in Prusaslicer with Prusament PLA default settings with these changes: .4mm nozzle .15mm layer height 3 shells 10% Rectilinear Infill Skirt Loops set to 0 6.35mm Brim (CopperTop, Bottom & Lid) Elephant Foot Compensation set...

Other two sliders would serve as limiters. For mode details on printing, assembly and usage see https://pedja.supurovic.net/3d-print-circle-cutter-adapter-for-dremel-proxxon-router-grinder/ https://www.thingiverse.com/thing:4656929...

The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.This model was tested with PLA material.To avoid printing problems, we recommend the following settings:ExtruderNozzle Diameter: 0.4 mmExtrusion...

The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.This model was tested with PLA material.To avoid printing problems, we recommend the following settings:ExtruderNozzle Diameter: 0.4 mmExtrusion...

PREFERRED PRINT SETTINGS: Nozzle Diameter: 0.4mm Programmed Extrusion Width: 0.5mm Layer Height: 0.3mm Shells: 3 (which results in a 1.5mm wall) Infill: 30% Infill Type: Grid Solid Bottom Layers: 3 (which results in a 0.9mm thick bottom) Solid Top...

The assignment was basically "here's two big sheets of polystyrene; go nuts." I finished the project in a few days, where two weeks were alloted for the assignment. For your enjoyment, I've included a picture of my two original prints. I'm going to...

The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.This model was tested with PLA material.To avoid printing problems, we recommend the following settings:ExtruderNozzle Diameter: 0.4 mmExtrusion...

I left the switch assembly itself, and the outer shell alone, so you can use those as points of fixed reference. * I added the vertical tube sections. There's no real resistance in there, so the material doesn't matter. It does put the...

Use lighter version if you would like to reduce the filament usage by ~30%- days (choose version you would like to have- with or without pin holes)- days_blank- used to fill empty space, you need 7 blank day tiles total- side_cover-...

The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.This model was tested with PLA material.To avoid printing problems, we recommend the following settings:ExtruderNozzle Diameter: 0.4 mmExtrusion...

at work (which is unfortunately forbidden), I would use the following settings: Layer Height: 0.1mm Shell Thickness: 0.8mm Bottom/Top Thickness: 0.8 Fill Density: 20% Print Speed: 50 mm/s This is for an Ultimaker 2 printer. I prefer to use PLA (we...

The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.This model was tested with PLA material.To avoid printing problems, we recommend the following settings:ExtruderNozzle Diameter: 0.4 mmExtrusion...

Needed materials to construct this battery pack are as follows.-The 3d print in this post-A 3S LiPo pack that fits the 3d printed shell. I'm using the E-flight EFLB32003S. It is a 3S, 3200mah 20C pack. I'm using this because I just so happened to...

Print Settings: Printer Brand: Printrbot Printer: Simple Black Rafts: No Supports: Yes Resolution: 0.1984mm layer height, 0.8mm shell/bottom/top thickness Infill: 10% Notes: A print profile is included in the thing files. Post-Printing: Initial...

The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.This model was tested with PLA material.To avoid printing problems, we recommend the following settings:ExtruderNozzle Diameter: 0.4 mmExtrusion...

The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.This model was tested with PLA material.To avoid printing problems, we recommend the following settings:ExtruderNozzle Diameter: 0.4 mmExtrusion...

The next dimension wave leaves Makertron a bit confused, but he meets some shell creatures who spend their entire lives in the sewer eating pizza. Nearing the end of his journeys, Makertron decides to copy the drone fad that humans are so excited...

The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.This model was tested with PLA material.To avoid printing problems, we recommend the following settings:ExtruderNozzle Diameter: 0.4 mmExtrusion...