neuron cell model

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_corner_radius = 5 custom_left_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

4028 fan mount: Note this is modelled with internal supports in the top section of the duct to make it easier to print. Please remove these supports after printing. 4 x M3 32 mm (upper fan mount) 2 x M3 x 12 mm cap screws (lower fan mount) 6 x M3...

This is a Core XY conversion kit for the Ender 5 with Linear rails There is a MK2 version here:https://www.thingiverse.com/thing:4777606 Big shout out to Scott3D for his fabulous work on the Hypercube Evo which I have taken the belt tensioner detail...

For the launcher and the “motor” (= nozzle and adapter) you can find additional info here: https://www.printables.com/model/46571-water-rocket-and-launcher-platform-complete-instru These parts have been proven to be working (see old video). The...

Theoretically, it can run more than 11 hours on 1 load (not tested). What parts do you need?Plastic parts:You can use the print files if you have an MK3S or you can use the model files and set everything up yourself. The photos show the position...

The solution is simple enough: Both parts of the model need to be placed away from the centre point (still properly lined up with one another, obviously), so that the probe can do its thing without the first print getting in the way. So began attempt...

Die 5W Lampen sind die falschen :PFalls die Halterung zum Anschrauben des Kombiinstruments am Armaturenbrett auch hinüber ist, habe ich noch eine Adapterplatte in die Dateien gepackt. Druckanleitung: Material: ABSInfill: 100%Brim:...

If you would like to view and interact with the model, you can click here. (You can hide parts by clicking and pressing ‘y’ on your keyboard)</p><p><strong>About</strong></p><p>This clock was created for the Timekeepers contest and utilizes the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_back_camera_x_position = 0 custom_top_port_corner_resolution = 8...

NOTE: Newest v2.0 of this model is now available - click here.NOTE: This is v1.1. If you were looking for v1.0 - click here. Note: As of Nov 16, 2023 — in addition to the earlier remix changes, today I added SVG files for engraving the plexiglas...

&nbsp;(Photoshop can also be used for creating the Bezier curves, but Inkscape is a freebie...)Retraced .svg image inserted into background in Fusion360 model file, zooming in &amp; out to make sure all line ends were actually connected (crucial!) -...

I was basically trying to address two "issues" of my Anycubic Vyper: - The PSU and Mainboard 24V fans are very loud - I want to upgrade my Vyper with an OctoPrint/OctoPi setup So here is my result: - An upgraded PSU cover featuring a 92mm fan mount...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

18-48V AC/DC voltage models are available for network systems and marine vessels. We also offer an additional 120-277V and 347V high voltage, 125-250V DC, and 0-10V dimmable versions of this explosion proof LED light fixture.Wiring: These LED light...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8...

There seem to be quite some error margin in production, if your model is a bit too big to fit, just sand off maybe .5 mm from the sides to make it fit.Completely(!) remove any filament remains inside the two enclosure parts.Fit servo into upper half...

I created this project to get more experience in modelling for 3D printing using Fusion 360, practice my soldering skills, and get a chance to do a little ESP8266/Arduino programming. *Features* hang it from the wall using the built in hole(s) or...

In Ultimaker Cura you first have to install the “Mesh Tools” extension which allows the “Split model into parts” action.Pneumatic tubes with outside diameter 3 mm are used. E.g. Festo PUN-H-3X0,5-NT. Locate the four holes in the housing and enlarge...

A wrench is used to unscrew the end caps for re-lamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap.7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

The pictures and model views all show the right hand frame. Most of the parts print without supports except for the inside half of the spool, handle post and reel frame that require “supports on build plate only”. I also use 100% infill for all...

The Version 1 is based on the original model, but with added material to compesate the extended face on the striker, and the second one is something I made because one of my magazines was giving me trouble, not really stoping when it needed. See what...

I just have to choose a bulb of the wattage I want and with a high CRI to get the best image quality.Since Fresnel spotlights are a classic in the world of cinema, I based my project on a model of the Arri brand from the 1940s. Which has a spindle as...

To use a different font than the standard Roboto (English) for either (or both) of the lines of text you just need to install the font onto your machine and configure it in the model parameters (in Customizer *locally* or in your .json file, more on...

Enable the Rotate_For_Printing option to rotate the part in this orientation. Supports: Depending on the options selected, it may be necessary to use supports. Rafts: Doesn't Matter License The "Sidewinder X1 FFC Riser" models (.stl) are licensed...

On the bottom of the print there is a text saying “Valentine 2022”.&nbsp;In case a name you need is missing, you can customize the model to show it: Please install OpenSCAD on your own computer and follow these instructions.If you could take a...

* Once assembled my new FelFil extruder (https://cults3d.com/en/3d-model/tool/felfil-evo-extruder-case) I began to design a cheap and affordable spool winder; I had to design a cooler for extruded filament and a digital sensor for filament diameter.

This is an OpenSCAD module library for propellers and spinners.This design models elliptical propeller blades that transition smoothly through three different NACA airfoils, starting with (by default) NACA 8430 at the hub radius, transitioning to...

Downloaded some Radio Control model yacht designs. Non of them suited my fancy for building, so I decided to come up with my own. Main Desing principles... No Keel! -> Surf Board / Windsurfer style. Light Weight (relative to size of jib!) ...

This brings the Muscle v2.0 advanced cooling system, originally designed primarily for Longer and Alphawise printers, to many more 3D printer models and users. I am even working on testing a custom X-axis mount plate for Prusa/Wanhao and other I3...

Wandering hour clocks have been around since the 1600s, but this one implements the concept in 3D printing!This example uses the case, dial pan, glass, and movement from an IKEA BONDIS, but the model could be scaled on the X/Y axes to fit almost any...