nfs shift 2 free download 3d models

Cura said it was a 9 hr job with tree supports so I added them as separate files as well if you want to glue them together and save 2 hours of printing. SHOPPING LINKS: I highly suggest buying new stepper motor cables so you can actually pull the...

i started with using an other Model as base and didn't check the dimensions 2. i realized my mistake to late XD 3. if i change the scale i would have to split in 3 parts because it would to long for the most Printers 4. i'm to...

Also, if you're planning to cram a bunch of stuff in there in addition to a 12V socket and power inlet, you might want to remix further to add more space inside before you print; a 20W power resistor + 2 big 15A diodes was already a very tight fit on...

Diameter of the spindle on Anet E10 is 8mm." Print Settings Printer: Creality CR-10 Rafts: No Supports: No Resolution: 0.2 mm Infill: 30% Notes: Print the knobupside down. No supports needed.</p> <p>I used 3 perimiters and a 30% infill, but you...

It also contains parts to covert your printer to house lipo batteries and be completely portable. Many details below and full companion video here: https://youtu.be/Cv5pEcBI5Hw Parts: Purchase the Monoprice Mini Delta: Amazon:...

The design of this toy was inspired by Theo Jansen's Strandbeest creatures, and combines 3D printing with some custom hardware to put the beauty of Jansen's walking mechanism in your hands. Kits are available for purchase here:...

The simplest method is to fit the duct fan onto the larger end of the adapter (See Image 2.) This will cut out the need of extra hose and clamps. Alternatively, if vibration does become an issue, then use a small section of hose to connect the...

I also used a GeckoTek plate to ensure perfect adhesion of the parts to the bed. Fred is in proportion to my other Flintsone models. If you have the proper filament colors, no painting is required. The model is 29cm tall. Enjoy, and I hope you have a...

I'm happy with how it turned out and had a lot of fun making it and I hope you enjoy watching the video!&nbsp;MaterialsNote: Read and follow all safety instructions and wear proper PPE.1 7805 5V regulator1 ATtiny85 microcontroller2 LS-0006 servo (or...

Step 2: Measure the length, width, and height of the wallet using calipers or a ruler. Record accurate measurements for future reference. Step 3: Create an assembly in your 3D modeling program, placing the hook onto the shell using the mate feature...

This is an example of what it should look like (G1 commands will be different for you so don't stress if it looks different): G1 X103.797 Y103.000 E0.0263 G1 X103.997 Y103.000 F1920 G1 E-1.5000 F1800; layer 29 G1 X190.000000 Y5.000000 M25 M17 G1...

Insert the actuator structure after you have glued 2 panels together. In the end glue the knobs on the actuators in such way that a smooth movement is possible (try out before you apply glue). When you build the box at once (alternative) plus the top...

I gave it 2 walls to make it watertight enough. Don't tighten the bolts with all of your strength, especially when you didn't print it with 100% infill. Also give the nylon parts some time (days) to saturate with humid air; acclimatization makes PA...

If 30 seconds of WiFi connection trial fails, it automatically moves to the the smartConfig mode (waiting for the setting from smartphone app.)Please not that your smartphone should be connected to 2.4GHz WiFi.Acknowledgement:Thanks to airtcp. His...

Printer: Anet A6 Rafts: No Supports: Yes Resolution: 0.2 mm Infill: 20% Grid Notes: Printed with a retraction setting of 1.5 mm using fluorescent green plastic filament, brim used for bed adhesion but may not be necessary. Post-Printing **A Few...

I would recommend printing the RGS Adapter 20.95 mm before the 21.05 mm version. Note: At time of upload, the design has not been tested in competition and has no guarantee of performance. Print Settings Printer Brand: MakerBot Printer: MakerBot...

Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: Yes Resolution: 0.2-0.12 Infill: 10-20% Gyroid or Cubic-Subdivision Filament: Generic ABS Black Notes: Suggest around 8 top/bottom layers as the sides are tapered and at...

The circular diameter of the nut, plus about 1mm (for a 6-sided nut, the distance between 2 opposite corners on the nut, plus a little), must be a sensible value compared to the nut block height. The depth of the nut countersink can also be adjusted...

Activity 2: Gauss Gun Tell the students to put on their safety glasses and assemble the model in the Gauss gun configuration. Distribute the magnets and have the students discuss for a couple of minutes how they think magnets work. Afterwards, have...

2- Disassemble the body There are four screws in the base and two holding in the circuit board. Cut the wires to the battery compartment near the batter compartment. 3- Reclaim the battery terminals The lamp takes 4 AAA batteries. We need the...

The horsemen of the first group (2-7) wear a fox-hide cap, short chiton, chlamys, and boots. The second group (8-13) wears only chlamys, while the third group (14-19) dons a short cuirass over a short chiton and boots. The fourth group (20-25) is...

Of course, the original electronics of the Tarantula do not support more than 2 extruders, so electronics modification is necessary.\r\n\r\nThe Diamond Hotend mount has been re-designed to better match the hotend to the height of the BLTouch. A...

UPDATE 7/4/23: I updated the body to include just one 30mm fan instead of 2 20mm fans. The 20mm fans were not high quality and I couldn't find any decent ones. New fans are linked in the parts below. I will provide some basic information on how...

http://www.thingiverse.com/apps/customizer/run?thing_id=287025 Instructions Using the following options: pixel_size = 0.7 picture =...

The Dragon Tongue - can be screwed to the Trianglelab Dragon Hotend V2.0 and used in the place of a standard E3D prusa V6.The adapter allowsone handed nozzle changing due to the Y-shaped "tongue" that fits the extruder cover shape and stops the hot...

4/2/15 - Yeah, screwed up that carriage extension piece. Way too thick for how much "meat" there will be on each side once I halve the carriage. Re-done now so should allow for both screw holes to be used plus extended where the rod will go to give...

The cloudy plastic version is slightly smaller and you will need to use my version 2 parts for it to work. https://www.amazon.com/Rubbermaid-Modular-Storage-Canister-1840750/dp/B00BEUDWIC/ref=sr\_1\_fkmr1\_1? https://www.thingiverse.com/thing:2598427...

Well designed Enclosure for Duet Wifi control board for 3030 extrusion frame Print instructionsUPDATE 3-Oct-2018: tximy remixed my lid for the Duet (2.0) Ethernet version - he even reworked all three lids! Thanks a bunch, tximy! <a...

1 perimeter should be adequate along with 15% infill and a minimum of 2 top and bottom layers. I like to print the infill before the perimeters. It gives a nicer looking layers because it smashes down the ends of the infill when laying the...

You just have to drill one hole right to longhole on the side of the pulley (just do the same on the second tensioner symmetrically), than use a small file, preferably a 2.5mm round file to extend the longhole to the drilled hole. This will allow the...