openSCAD Parametric Filament Spool Adapter 3d models

Print time is about 9hrs 45mins, and uses about 90g (30.5m) of filament. Printer: Prusa i3 MK3S Rafts: No Supports: Yes, but on baseplate only Resolution: 0.2mm Infill: 20%-25% Perimeters: 2 to 3 After printing, one of the long M3 screws can be used...

It has a print-in-place kickstand for when it's undocked; the kickstand is held closed by a pair of press-fit 3x3mm cylinder magnets.. Here's a rough parts list: 1/2" x 1/4" x 1/8" neodymium bar magnets (8) 3x3mm neodymium cylinder magnets (2) ...

There are spaces for eight magnets, but in practice a pair of 1/8" x 3/8" magnets or four 1/16" x 3/8" magnets per side are more than sufficient.The version the I built uses a 1:48 geared motor, but the 1:90 geared version would be more appropriate...

Lay a piece of filament in that gap and smooth it out with a soldering iron, or you can use a 3d pen, if you have one. After getting it as smooth as you can with the soldering Iron, sand with light grit sand paper for final smooth finish. if done...

Height loss can be minimized by using a very short teflon tube at Orbiter entry and feeding it with filament from above the printer. This avoids running a reverse Bowden tube between the gantry and the upper printer frame extrusion. - Both...

If you like my work then please do not forget to "tip designer" to show your appreciation and to encourage me to publish more designs in the future. Print Settings Rafts: No Supports: No Resolution: 0.2 lampstand 0.1 lithophanes Infill: 25%...

I would recommend PLA, but other filaments would probably work as well. Use a 0.2mm or finer layer height. All parts print without supports.</p><p><strong>Assembly</strong><br>In addition to the 3D printed parts, you will need:<br>12 - airsoft BBs...

I used switches like these: https://www.amazon.com/gp/product/B07T1JG6BD They include a pilot light, which is not necessary but was simple to implement. Print Settings Printer Brand: Creality Printer: Ender 3Rafts: No Supports: Doesn't...

The specific settings should depend on your printer and the filament used for printing. Placement of models on the printer table when printing is shown in the photo the Cura slicer shows a scaled-down model using the slicer itself. Its files For CNC...

Let me know your experiences and if the priming line interferes with the portal frame due to its large size. It is possible for the frames to be moved a few millimetres forward to avoid the priming line.Update 18/07/2024: Added commercial licensing...

All three designs have gone through multiple iterations, each printed and checked using an UpMini printer with a heated bed and ABS filament. Each DOMOBIT features a bottom surface with concentric ridges that makes raft removal easy and adds a touch...

PLA from Overture -200c, Inland (MicroCenter filament) 210C (it’s your choice). All was printed at 0.2 resolution - This was a lot of test prints so it saved time and looks decent. I have an upgraded hot end (E3D V6) so temperature may be...

PM me or contact me via stan@3dpt.club for details. Print Settings Printer Brand: LulzBot Printer: TAZ 5 Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: .3-.4 mm Infill: 5% Notes: I printed them in clear filament so they can lay over a...

The specific settings should depend on your printer and the filament used for printing. Placement of models on the printer table when printing is shown in the photo the Cura slicer shows a scaled-down model using the slicer itself. Its files For CNC...

There are plenty of videos on Youtube available to explain this process I would recommend for Cura the video by CHEP - Filament Friday and Fugatech for a tutorial using Simplyfy 3D. I have also included blank decal plates for individual...

3 perimeters for everything else - Don't use trash filament, no matter how well designed, springers require a degree of material integrity. - When post processing, be sure to nicely remove any elephant's feet with a scalpel or a knife. The SpringCap...

A wireless gamepad/controller option is enabled by fitting a holder for a USB ‘dongle’, plus an ultrasonic sensor and an OLED are also fitted to the robot to sense nearby objects and to display the current ‘status’ of the robot.It should be noted...

You won't need all of them, but the filament also costs a few cents. So lets say 20$. <h1>Important information:</h1> Length of the carbon tubes: 8mm diameter (you need 970mm in total): 1 x 320mm (front motors) 1 x 290mm (back motors) ...

The code was written in Visual Studio using the Visual Micro plugin. Print Settings Printer: HyperCube Rafts: Doesn't matter Supports: No Resolution: 0.2mm Infill: 50% Filament Fillamentum Vertigo Grey PLA Notes: Multi-Material/Dual extrusion...

It would be a good idea to print this part at the low end of the temperature range for your filament and at a lower print speed if you have any issues with it. Most of the part is covered/hidden, so any defects will not show anyway. 4 - A number...

... backplate spacer that also interfaces with your X switch, and a relocated probe mount that clears the switch housing and homes well off the bed. (Thanks to Thomas Young for the help and filament to prefect this, I couldn't have done it otherwise)

Since many of my friends own the 18V Makita battery system I thought of a practical Christmas present for them.I got the idea for the basic platform from user "bitplusatoms" with his design "Makita Battery Mount"...

It is well designed and the dual driven hob pushes filament like no other. There are 2 versions of this mount. One that uses ball studs and another that uses SeeMeCNC nylon barbells, and should work with the machined aluminum barbells available from...

But the final product is worth it imho.&nbsp;Having said this, if you still want to go ahead it this mini project, let me guide you for the whole process.&nbsp;Printing:&nbsp;Material: PLAInfill: 15%Supports: No, except Maybe-No.stl (3mf available...

Materials needed: ESP8266 - NodeMCU v3 LM2596 SMD - Buck converter 2 x 18650 - batteries WS2812b - NeoPixel LED strip Resistors: 560 kOhm 220 Ohm Filament Wires CA glue (super glue) Body filler for plastic (bumper) - optional ...some patience Tools...

&nbsp;If you have the proper filament colors, no painting is needed.The assembled model is 270mm tall.Enjoy!...........................................................................................................**Print Instructions:**Supports:...

https://cults3d.com/en/3d-model/home/horizontal-drain-system-for-hydroponic-tower-pack-and-green-wall-pack THIS PACKAGE INCLUDE MORE THAN 85 STL & DXF FILES AND IT CAN BE YOURS TO PRINT, FOR PERSONAL USE, AT THE EQUIVALENT PRICE OF A CHEAP 3D PRINT...

This takes a full roll of filament or more to print. Each side of the cube takes me 12-13 hours to print on my machine. You need to print nice and slow. If you go to fast, the path wall get distorted on the end and the ball won't fit. You'll also...

... on that page. It still works with a universal remote. The program also has some bug fixes.Print SettingsPrinter:FolgerTechResolution:.2Infill:20%Filament: Xyltech PLA&nbsp;Notes:tilt crank is the only part that needs supportsCategory: Robotics

If you are interested in testing mounts for different sized bottles, please contact me and I will make one to fit your bottle.Print SettingsLine width: 0.4-0.45mmLayer height: 0.20mmWalls/perimeters: 2-3Infill: 20% except Core Type A Center: Infill...