operation game versions 3d models

I'm exploring the idea of a printable base height extension but would welcome any ideas on how to design shorter versions of these cams. ### Printing Use plenty of infill for strength. Rotate parts so that surfaces vital for concentricity...

Il mio codice è un codice base da dove iniziare a personalizzare il proprio in base alle proprie esigenze .Quindi poi sarete voi ad integrare altri comandi .Seguirà in futuro una versione senza fili con batteria annessa.Logicamente non sostituisce...

Customized version of http://www.thingiverse.com/thing:368375 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: ...

Customized version of http://www.thingiverse.com/thing:368375 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: ...

Customized version of http://www.thingiverse.com/thing:368375 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: ...

The one for juice could afford to be a tad tighter and I might release another version of it. The one for soda fits nice and tight and will actually lift a full 20-oz bottle once it is nestled in. Please refer to the print settings for other...

The supports (other than brim) may NOT be needed, but I had problems with previous versions wobbling as it got higher, so you mileage may vary. The more I think about it, I really don't think the supports will be needed - let me know. :-) *VERY...

Customized version of http://www.thingiverse.com/thing:116042 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: ...

Print first version of student designs. Only do one pin until the students have shown that their design works in more than one VeggieMake piece. These prints should be fast (less than 4 min) but it is a good time to break if needed. Students try...

There is not enough space between my version of rear extruder part and Z-axis profile, but I can do much about it. Solution which I´m using is pull-out sleeve from the profile and leave there just cables as you can see at pictures...

This is a Core XY conversion kit for the Ender 5 with Linear rails There is a MK2 version here:https://www.thingiverse.com/thing:4777606 Big shout out to Scott3D for his fabulous work on the Hypercube Evo which I have taken the belt tensioner detail...

Customized version of http://www.thingiverse.com/thing:116042 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: mirror...

The length of the silent period varies depending on the button pressed. Here are the values for each direction: Forward: continuous 41.7KHz carrier Reverse: 1.982 millisecond bursts of carrier seperated by .143 seconds of silence Left: 1.982...

Customized version of http://www.thingiverse.com/thing:368375 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: ...

The dials are provided in Illustrator and PDF, and use the DIN typeface (open source version here).Parts requiredAngular Clock, board only (not the kit)Square 3" panel meters. This model is designed specifically to accommodate <a...

In the first version, I decided against an adjustable current limiter for the time being and instead fused each charging port with a 5 A fuse. Should I determine during use that a freely adjustable current limit is necessary, I would still retrofit...

This is based on Marlin k-factor generator with Prusa specific G-codes and settings. Naming convention for the G-code files: LA1_5-"Filament"-"Hotend temp"C-"layer height"mm-"fastest perimeter printing speed"-"Extrusion multiplier"E_mult-"Prusa...

If you want to be on the safe side, set support On for everywhere and set the overhang threshold to 5 (five degrees) (Advanced settings in PrusaSlicer)After slicing it should look like this: Book back cover clip(s) for magic bookshelfSame settings as...

Customized version of http://www.thingiverse.com/thing:116042 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: shape...

Having purchased a Corsair HS70 wireless headset I wanted a wireless version of the TrackIR ProClip to go with it. Using this mount I now have an active clip with a battery life measured at around 35 hours that mounts magnetically and switches on...

I also use an older version of cura making adding temperature changes a pain so I wanted some way to just have it done automatically with no special slicer setting. When I set out to design this tower I wanted it to fulfill the flowing criteria: *...

Please check the images to see what it is included in this kit.This set contains: - Cultists of Melmora (12)- Plague Knights (4 + 4)- Fosco – Herald of Melmora- Fallen Saint Mordentus – the Penitent- Blasphemia – Daughter of Decay (Cultist...

On the bright side, all it requires is a 3D printer with no further effort to create.This remake, the Foťák Rail version 3, is much more flexible. For starters, the two holes for the 15 mm rails are now slightly larger, with a diameter of 15.3 mm. We...

It is well designed and the dual driven hob pushes filament like no other. There are 2 versions of this mount. One that uses ball studs and another that uses SeeMeCNC nylon barbells, and should work with the machined aluminum barbells available from...

Customized version of http://www.thingiverse.com/thing:368375 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: ...

Before printing, make sure you have the same version of the board. The dimensions of my board is 65.75x35.2 mm, the adjustment screw is shifted 14.4 mm from the center to the right. Also look at the photos that I attached to compare the position of...

This is a Core XY conversion kit for the Ender 5 with Linear rails There is a MK2 version here:https://www.thingiverse.com/thing:4777606 Big shout out to Scott3D for his fabulous work on the Hypercube Evo which I have taken the belt tensioner detail...

See the same thing in countless other sports and industries all the time, and even more crazy with 3d printers in the mix.  DesignI got a functional version of this early on, in about 10 drafts and a month of work. Making this a real worthy piece of...

I'm still working on a version that uses contact/spring plates for the batteries so that you don't have to weld tabs to the cells, but for now this is the smallest, fastest way to build it. Tools required: - 2mm Hex key or driver - Soldering...

ESP32 DevKitC (v1 or v4 tested)...