pebbles from flintstone 3d models

The sweet spot for balance seems to be 22 BB's in the front section and 8 in the rattle section. 7-27-17 = Tested the new version this morning and it seems to swim great now with the new weight (BB) counts and placement. 11-10-20 = Uploaded Rattle...

Pick which one you want. What are all the issues I had getting this to work and how did I get it to work? See the txt file of notes that I just added (5/9/2020) from a year ago that documented all the fine tuning and installation steps of getting...

... - 60mm long and about 3mm thick. Used to hold the lipo in place. From underneath the base, put one end of the rubber band through the rectangular slats and the other end through the other slat making two loops to hold the battery down. ...

**Note: From now on, build notes will be posted to the changelog.txt file uploaded, with only the latest notes added below.** Hey, you should also check out ViperMan's set of organizing trays here. Yes, I will come back to this soon and do something...

**Initial Fan Speed:** The fan speed was set at 0% during the initial layers to prevent debris from being blown away prematurely. **Regular Fan Speed:** Once the first four layers were complete, the regular fan speed was kicked in at 100%. **Print...

;) Taken from my ruler stop. <a href="https://www.youtube.com/watch?v=DNR58DfmLSM">https://www.youtube.com/watch?v=DNR58DfmLSM</a></p> <p>My calibration sequence (sequence is impotant) is:</p> <p>-Take care, that your printer stands on level...

Tips are also appreciated if you'd like to see more files from me or if you would like to request changes or updates to files!&nbsp;A goofy bobblehead where the bobbles are booty cheeks.Assembly:Print one base: gives the model stability, but can...

I want to make it so that only a few pieces would have to be reprinted to go from static to RC. I've also been working on the mast and rigging setup and should have those files posted soon. I do plan on putting together an instruction document but...

The firmware compiled from this configuration takes about 36kb of RAM and 404.5kb of Flash memory. If you have a 512kb there will be no room for the firmware for OTA updates. Electronics BOM: 1) ESP-01s 2) 5v to 3.3v downshifter to power ESP-01s...

Each time Ortas publishes this content, you will always find many completely new models – today we currently present nearly a little under 1 hundred forty different designs from which each of one may be changed individually or even collected by...

Using the following options, create a customized version of this thing from Thingiverse: http://www.thingiverse.com/thing:287025. ... Customizer Options: - Border Width: 1 - Pixel Shape: 4 - Panel Shape: 1 - Thickness: 0.5 - Pixel Size: 0.7 -...

Apart from printed parts you should cast a silicone brush using one-time mold (cast, destroy the mold, use your silicone part). Also this cleaner occupies only ~1cm of printing surface if you bend it and move outside of the print bed (see photos). ...

You can fine tune it to add extra support and we've included some visual aids to help you. We've also included over 5,500 hard drive holder STLs that we've generated from this design. This design is*completely free* and shared under a permissive...

There is no electricity used as well as no pumps and wick needed, also don’t have to change nutrients in the reservoir much often like other systems.&nbsp;So theoretically, Kratky is a low-maintenance system that can work on its own for weeks...

I recommend printing the couplers according to their polarity to make it easier to match them up.&nbsp;&nbsp;After the magnets have been placed, use the printer's menu to resume the print.&nbsp;For the back of the MMU2S, I used short PTFE tubes,...

I have provided these as a reference point, but you should measure your own installation for accuracy. The BLTouch / 3D Touch mount is a recreation (with modifications) of one of the BLTouch mounts from the Hero Me Gen 5 suite, so full credit to...

The chuck that holds onto the miniature is designed to be portable (modular), so you can quickly attach to, or disconnect from, the other parts in this system using the rare earth N35 magnets. You're not limited to only 1 way to paint your...

Human: CAD Cart 1 is a one-stop solution for creating stunning CAD, renderings, videos, 360-degree views, catalogs, and model views of exquisite diamond jewelry designs.\n\nWe provide precision CAD files of the following jaw-dropping...

Determine the height of the device at the front of the stand that will prevent the device or object from sliding off the stand. This can be the measured height of your device or object, if applicable. Enter the value of the `stopper height` into the...

These reduce the diameter of the slots from battery size AA (HR6) to battery size AAA (HR03). Optionally, the texts "VOLL" and "LEER" can also be printed and inserted into the provided recess and each fixed with a drop of adhesive. I printed the...

It helps hold the vertical tie rods from bowing out in the centre. My original design does not have this and although there is some bowing (as the plexi tries to flatten in the centre) it does not appear to cause much of a problem. This design...

This ensures a consistent print from top to bottom, it also means you only need to check whether the bottom level of a model will print correctly, because the higher levels will be printed in exactly the same way. The same goes for the order...

That is pointed out in the screenshots from PrusaSlicer. If you're anything like me, you hate supports. So there's my gift to you. Now keep in mind that this is version 26, but not the final. Really, I'm never going to stop working on this design....

To assemble a tripod, use 1 head, 3 wood sticks and 3 feet. You can secure the mount with 2x12 wood screws. Those screws are just for mounting, no forces are transmitted. Ensure the tripod aligns well in the 380mm circle. Repeat this procedure 2...

It also utilizes commercially available waterproof components to offer a weatherproof and completely sealed body, protecting the electronics from the elements. Though not a beginner-friendly project, RTE-1 is relatively a simple construction. The...

The transition from the infill to the top solid layers is rather hard for the printer because of the many interruptions in the diagonal due to the hex bit holes. So the print needs several layers to recover a smooth surface.</p><p>I recommend 15%...

I bought springs from russian manufacturer called MW, you can get Maple Airsoft Super Feed springs price is about the same. There might be more springs that I'm unaware of. Next there will be Pmag Discord for feedback : https://discord.gg/DPYEGvH ...

Their purpose is to prevent the tray from sliding when placed on top of the lid, both when in play and when storing multiple stacked trays in between sessions. * Optionally, one each of the small and large card dividers. They are intended to separate...

&nbsp;The flat side from the printer bed faces back. &nbsp;The holes are notched and the whiskers only fit one way. &nbsp;Personally, I had to keep poking around to fit them in but once positioned correctly they slid right in.</p><p>6 - Refer to the...

So I decided to create it from scratch.This modular storage system was optimized for printing in vase/spiral mode using 0.8mm or bigger nozzles. Printing in spiral mode was one of the main requirements for modeling due to its lower filament...