pinhead puppet pattern free 3d models

I am keenly interested in optimizing this concept so that it Works for those needing a good, quality, multi-purpose coral frag plug so please leave comments on how I might improve this Thing. Instructions Additional fragging tools that might be of...

Wheels to axle : M3 leafspring to axle : M1.4 Leaf spring brackets assembly : M2 Leaf spring to bracket : M2 end of stab leg : M2.5 Female ball joint adjustment M2,5 flat ramp bracket on ramp and on trailer : M1.4 stab legs on brackets : M2 Rims...

None of these models should need any support, I try to avoid them if at all possible, but you will need to be able to bridge somewhat decently. I personally used Overture Easy Nylon, it's very stiff for a nylon that doesn't seem to creep and...

And for many builders I consider this simpler than going the path of printing Flex material.  Model DetailsPulley and Bearing Press ToolThere is not much to say. It shows the pulley with a bearing and heat-shrink tube on the outside. The third...

Initially I modelled the candle I wanted, then using boolean operations subtracted it from a cube, and split the cube in half. ...Then I added the pins and matching holes just to help align the boxes and hold them together a bit by padding and pocketing...

I found when doing this I had to clean my hotend and its was really difficult with this model. ... I included my wires for my NEMA17, but I can tell you right now, your NEMA17 will not be the same, you will have to figure out your pinout by yourself,...

This model is cheaper than the usb c version and charges the Oculus Quest perfectly. This greatly improves your playing time and you could even charge the battery while using it. One design came close to what I liked, but was made for a different...

Tensegrity model maintaining stability with one single wire.Materials needed:0.5 mm nylon wire7x M3 nuts7x M3x10 mm Allen screws (longer ones were cut to the right size)wooden plank of about 55 cm2x 50 mm wood nailsThe spiral parts are designed to be...

Not a problem with a well-tuned MK3S+.    The box was printed usingFilament                                              ...

the better the less likely it will grab but u can always use nuts on the other side even tho i didnt make a place for them to sit on the model since i had planned on using the threaded inserts but it will still work cause thats how i test fit...

I have no model or figure of Buffaloman in a camo tank top. The bazooka is actually pointing backwards to simply be held resting on his shoulder. I scaled it to 40% and positioned it to be resting between two shoulder spikes with the hand grip...

This was my first prototype, there are always rooms for improvements….I am afraid this cannot be print on a Mini+:(The biggest model is 188.90 (X) by 202.60 (Y)I have been looking for raised pet bowls that looked nice and highly customized without...

I have not included the CAD model: As a newbie, I made a fair mess of things whilst modding along and fear that the kind people of Autodesk would take away my Fusion hobby license:)That's it!DOWNLOAD NOW for limited access to the crack attachment:) A...

... screws. Now you can start the tank with the key and load it without opening it. PS: The original model has more than 200 rivets that the FDM Printer neither sliced nor printed. ...So if anyone wants a riveted version for a resin printer...

It provides a list of the models. A typical tower includes mostly about 20-30 function calls, generating Lego block elements plus some openSCAD "hand code". If you download the full Doblo Factory code (http://edutechwiki.unige.ch/en/Doblo_factory,...

The build and schematics can be found at: https://www.printables.com/model/282166-runtime-counter-v-20 This box will fit in the enclosures made by Stepcraft. Hardware: DS 15 connector female (signal out) DS 15 connector male (signal in) Mono...

OK, this isn't a model but rather a gcode script to facilitate automated cold pulls to clear out your nozzle. I use it all the time on my Ender 3 and thought others might get some good use from it as well. **What is a cold pull?** A cold pull is...

I built the flat surface of the skirt with ParametricPlot3D, then intersected it with a lattice-like model, then I utilized those tables to make two ParametricPlot3D tubular surfaces, which I then pieced together using the Show command to make the...

NOTE: all models are at initial stage and not refined, nor optimized for printing, only a rough idea at the moment The unmanned colony builder/Mars MkI is a project that seeks to automate the construction of shelters and basic facilities that a...

It is possible that a future will make and upload a model of that piece. In the meantime, if anyone knows where to get suitable pads, please let me know. As I was saying, I started to hang them on the screw. Since the surface of the screw with the...

My prototype box had a problem in which the combination could be guessed by feel due to the slack in the model. This problem was fixed with a number of features that make guessing the combination by feel very difficult. As an additional precaution, I...

&nbsp;Obsolete models are deleted and replaced with the latest version. &nbsp;Post feedback so we can improve and keep these collector replicas running!</p><p>Change Notes</p><ul><li>4/5/22, Version 6: Best version yet. &nbsp;Dimensions tweaked for...

This stage can be handled in several ways: 1: The instructor can have several models pre-made for demonstration and discussion. 2: The instructor can have kits of parts put together for students to work with and attempt to build their own trusses. 3:...

# Anet AM8 motherboard case This case is inspired by a [YZ Case for Prusa made by Carter](https://www.printables.com/pl/model/1910-yz-case). This case is prepared for mount on the Anet AM8 modification frame. It can hold Anet A8 v1.7 motherboard...

If you're using another fan make and model, make sure you check the polarity so it isn't reversed. If you don't have crimping tool you can just cut off the connector from the original fan and solder/splice it on.</p><p>Print the 3 (4) parts. If you...

First, I had to model the front of the display to accommodate the RepRap Discount Full Graphics Smart Controller and then I also decided it needed a back to protect the circuit board. Done... Then I decided to tackle the problem of mounting a...

Although mine is 17mm long you can scale this with your slicer (Z axis only) when you slice the model to change the space from the wall. Use as many as you need around the edges, corners and middle parts of the perforated board.</p> <p>The spacer...

... most of these parts. If there are any tweaks necessary let me know. I have added a .step file of the assembled printer and I will upload a Fusion 360 back up file as soon as its processed so you guys can go nuts customizing the solid models.

In order to make it much easier to assemble the case with the RPi4, a few changes were made:Divided the lower part in two halves for easier inserting ofRaspberry Pi;Added snap fit link between upper case and lower case;Using four M2.5x4 screws is...

... cut methodology used. All credit for the idea to use them as puzzles goes to Quadratum Cubicum (QuCub.com - no author name noted) and this was already licensed under Creative Commons Attributable before I modeled the pieces and the base/lid. ...