printrbot support 3d models
553059 3d models found related to printrbot support.thingiverse
... and ensures that the cable will not interfere with your prints! Print Settings Printer Brand: Printrbot Printer: Simple Black Rafts: Doesn't Matter Supports: No Notes: Print with a brim to ensure bed adhesion. ...How I Designed This Fusion 360
thingiverse
I plan to connect these to the inside walls of my enclosure, but I m sure angled brackets could be designed to secure to a base, or table or additional part coming off of the Printrbot base to create an "A" frame type design similar to a lot of the...
youmagine
A simple little clip to keep the cable on the Printrbot Simple Metal out of the way. ...It only requires a couple of minutes to install and ensures that the cable will not interfere with your prints!
thingiverse
This is a support in order to attach a fan laterally to the gantry that supports the extruder on an original Printrbot . For the gantry please take a look at my other files . You need to rotate around X or Y so you can print it without support on its...
thingiverse
The threads didn't come close to fitting but after some sanding and a little glue it assembled nicely.
thingiverse
... surface area to displace the weight of the printer and hoping to reduce vibration and increase stability. ...if there is another printer similar in construction to the printrbot I'm sure this would work too. ...I printed four of these for each corner.
thingiverse
printrbot simple 1405 usb fix: supports the cable while printing so it will not cause problems or fall out due to vibrations or accidental knocking it out . ... use the spacer for a better fit.
thingiverse
40x40 Fan support for the Printrbot Simple Kit. ...Just attach it onto the Y-Axis as shown in the pics :)
thingiverse
Filament Support designed to use with a 25mm tube Print Settings Printer Brand: Printrbot Printer: Simple Black Rafts: No Supports: No Resolution: 0.2mm Infill: 40% Post-Printing
thingiverse
... USB plug from ripping out the delicate port from the circuit board. ...Works for my oval-shaped USB plug heads. Print Settings Printer Brand: Printrbot Rafts: No Supports: No Resolution: .20 Infill: 20% Notes: Be sure to lay large face down on bed.
thingiverse
This part clips onto the tower accessory for the Printrbot Simple. It keeps the wiring from dragging on the print bed. Instructions The part has a hole for an M3 screw, but it holds nicely...
youmagine
I wanted to do something more for the Metal Plus, I thought it deserved a nice LCD support.If anyone needs I can upload my Gcode, *igs or *stp.
thingiverse
This is for mounting an E3D to a Plastic Printrbot. ...Carriage should be upside down. Not tested yet ... Print Settings Printer Brand: Printrbot Printer: Printrbot Plus Rafts: No Supports: No Resolution: 0.2 Infill: 20%
thingiverse
Instructions Well first I sat there looking at my printrbot for some time watching the rod wobble as the z-axis made every move. It bugged me and i looked closer at where the nut was placed. Very bad design if you ask me. I got out the calipers and...
thingiverse
This is an adapter / support to perfectly fit the Dyze Design DyzEND on the Printrbot Simple Metal printer. dyzedesign.com The precision is incredible!!! I loved it right away!!! As far as I am concerned this hotend is a major upgrade for this...
thingiverse
update 02/06/2014 small problem with heat when i print over 4 hours, so i angled the fan lower, plus i made some clams for the cables (Fan-MountV6) update 29/05/2014 still some noisy, os i switched to my 80mm fan, no more fan noisy :) (Fan-MountV4) i...
thingiverse
I designed this support piece to prevent the main cables from touching the printer bed. So far so good! Just print the model twice and glue the two halves together, surrounding the cables. ... Then slide it to the bottom and glue it to the rubber...
thingiverse
Support de câbles, pour évité de tirer sur les fils du moteur Y Fixation encastré, avec Auto taraudage M3 et rangement BTR ou autres. ... ...
thingiverse
The standard plastic printrbot base allows the z-motor to rock - this one doesn't. Optionally you can also use linear bearing clamps instead of zip-ties to hold the y-bearings in place. My tested clamps have 4 holes for screws. I've added other two...
thingiverse
A support to hold the extruder wire harness so that it doesn't drag on the table. It's held by friction, designed to fit snug under the extruder motor without putting undue pressure on the motor. ...
thingiverse
This thing adds support to the GT2 belt bearings by mounting on top of the bearings via the NEMA17 holes and fitting tightly around the screw heads that hold the bearings in. This way the screws are supported on both ends. I made this after I had...
thingiverse
Instructions Download this version of the STL : http://www.thingiverse.com/download:109372 Just replace the stock printrbot base with this thing. There is one version with a support to attach the Y-stop switch. Just put a wire-strap through the...
thingiverse
I borrowed the clawfoot design ( https://tinkercad.com/things/2x5aMtWwHrW )and modified it to fit the Printrbot 1405. Simply print 4 of these out and remove the back supports. I painted mine (yes its a bit sloppy) with fingernail polish. Slap 2 on...
thingiverse
After so many issues with a stepper that was overheating and destroying also the supports I decided to make a support that can be easily swapped without needing to dissasemble the Printrbot .
thingiverse
Print Settings Printer Brand: Printrbot Printer: Simple Black Rafts: Doesn't Matter Supports: No Resolution: 0.2 Infill: 50% Post-Printing Instructions Print Bed Support and one left and right bed rail (With or without support cutouts). You will...
cgtrader
The standard plastic printrbot base allows the z-motor to rock - this one doesn't. Optionally you can also use linear bearing clamps instead of zip-ties to hold the y-bearings in place. My tested clamps have 4 holes for screws. I've added other two...
thingiverse
... to take advantage of the aluminium blocks on this carriage to bolt into, making a much firmer attachment. Stock, PB recommend you bolt the leadscrew supports into plywood holes on the carriage, which strip easily and flex a lot, causing banding.
thingiverse
... to take advantage of the aluminium blocks on this carriage to bolt into, making a much firmer attachment. Stock, PB recommend you bolt the leadscrew supports into plywood holes on the carriage, which strip easily and flex a lot, causing banding.