q1r quick release 3d models

 The heater is mounted via a quick release system to let you remove and add it with ease along with an articulating screen to allow you to view and adjust it from the front of the printer.I will preface this that upon completion I decided to go with...

**VERSION 2.0 is up** This is a bench side quick-release mount for a Lee Breech Lock hand press. Allows to operate the press in mounted position (better for priming and especially powder charging) and quickly detach to operate in hand-held position.

Since this design is based on N1bbles awesome Quick Release (https://www.thingiverse.com/thing:3317013) a lot of the info there applies to this one here as well. So I'm just gonna copy/paste the most important bits.</p> <p>printed out of PLA with the...

This is quick release buckle for Flysky Nirvana NV-14. Printed in PLA or other material, Layer 0.2, Brim and supports are required everywhere, use roof/floor settings in Cura for better quality. Infill settings should be between 25-30% for PLA, or...

Most tripods only come equipped with one mounting plate, but when I see the quick release camera mount for Ambico/Velbon tripod, I like the idea so much that I repurpose my Sigma EM-140 ring flash holder's camera holding part and add a foot that fits...

Quick release canopy mounts for Specter V2 / NME Didn't like the stock canopy attachment so here goes... LIABILITY DISCLAIMER: Use this model at your own risk. By proceeding you acknowledge that the creator is NOT LIABLE NOR RESPONSIBLE in any way...

Thrustmaster Steering Wheel 'Suicide' Spinner Knob Quick Release I remixed this because I wanted a tool-less knob that I could pop on and off easy, and I wanted it to spin a little more freely with bearings, so... Fits my Thrustmaster Force...

I've redesigned the quick-release Laser Adapter to fit on the Anycubic i3 Mega. The 500mA laser is attached to the (+) positive and (-) GND line of the Fan0 Port (trigorilla 1.1), and controlled via G-code. I've set a switch to cut off the fan when...

Since I have multiple cameras and do not want to switch the quick-change plate for the tripod every time, each of my cameras gets its own quick-change plate.

New Concept - Quick Release for Sim Racing Steering Wheels \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ UPDATE: 2/10/2022 Uploaded a Locking ring with a single...

A quick release interface bracket for the Telsa wall connector Gen 3, 3 phase version.I'm not sure if it fits the single phase version, please let me know.If you add a Plug and Cord to your Wall connector, you can take it easily to use it as a 3...

Hi Internet Sim Peeps, At request, I've whipped up a TMX/T150 to stock Thrustmaster Quick Release hub adaptor. Now, I want to preface this with the fact that I don't have a TMX or T150. I've used reference images and materials to gather the...

It is a 12 x 100 mm thru-axle (TA) fork, with 1.5 mm thread pitch. The idea is that while the over-locknut dimension (OLD) is 100 mm on 99% of front quick release (QR) wheels, the M9 x 1 mm hub axle itself is nominally 108 mm wide. Standard QR forks...

A front wheel hub, featuring 36 holes and equipped with a rapid-release mechanism, is designed specifically for use on bicycles. ...This convenient feature ensures easy installation or removal of the wheel without requiring any tools.

Quick Change Adapter for König Tripod KN-TRIPOD20. ...I've applied a thin layer of adhesive to the cork on top, ensuring that this adapter stays firmly in place and eliminating slippage entirely.

Modified QR Adapter for N1bbles Sim Racing Quick Adapter - https://www.thingiverse.com/thing:4572839 use 3 bolt only, the basic m5 bolt from ThronEisvogel1 was tapped to the adapter already no nut needed

A UWL-01 wet lens holder requires an M52 adapter and attaches to the strobe tray for quick lens attachment/removal. Safety dictates use with http://www.thingiverse.com/thing:173648. For print, opt for high infill, quick print, and robust plate...

The options sold to adapt to the standard camera screw don't work well due to the rubber cap on the quick change plate. This custom part locks into a Neewer size quick disconnect plate and provides a stable 1" ball mount to work with. I would suggest...

Remix Requested: A quicker release system for @kingkuul's desired setup, swapping out the traditional rubber ring for a hard, fast solution. ... Considering a typical 1-inch tube as the standard base, it's recommended to add an extra layer of foam if...

Quick-connect pneumatic fittings are available for efficient and hassle-free assembly of air systems in various applications. These fittings ensure a secure connection, reducing the risk of leaks and saving time during installation. ...With their ease...

Quick-change heads without a screwdriver. Store extra heads on the back of the Z-axis. Avoids damage to toolhead, bed, and X-axis from toolhead running into bed or workpiece. Suction attachment can be used with mini shop vac to gather dust from the...

Quick change battery mounts for rdq 650 4s, Emax 850 4s, pyro drone grafpene 1100 4s. Lock faces front of the quad in back of your naked camera. Use small piece of ummagrip of each side to keep from slipping. ...These are 8 grams per.

I found releasing and fastening blades on my scroll saw very annoying, when using the original lock nut: Rotating the nut takes ages and when fastening the blade, you always have to find the right position to achieve the correct tension on the...

My G29 Quick Connect ================= Features: ------------ - Quick change between wheels - easy to print and use - cheap - use VGA DB15 for connection between the wheel and the base I used [this bike seat clamp...

... on top. ...And that's it, you now have a replacement! Tested - working perfectly. To get started, you will need: * This printed part * A 1/4'' screw/bolt like this one (approximately 1€) * Foam rubber or cork (either self-adhesive or glue it yourself)

This is a rapid release plate designed specifically for the Fotopro FPH-2W tripod head, which comes equipped on a Fotopro FY-683 tripod. The plate might also function with other tripods. It's just a simple plate. Download the STL or STP file and...

Hi, I was bored with using a screwdriver to release my wheel from the wheelbase. I wanted to use the screw as intended from the Thrustmasters manual. So i decided to make a little handle for it that uses the original screw.The handles tolerance is...

I often use my ATH M40x headphones without the Modmic attached, so have a quick clip system instead of using the default clips is much handier. They're roughly designed after the default modmic clips, but moreso iterated for a tight, no-slip clip on...

Advantages: ---- - 3D printed :-) - change sand paper quick and easy - sand paper fits perfectly - perfectly flat and hard block for precise sanding e.g. of edges - sanding belts are cheap and readily available in this standard size - sanding...

Here's one of the handiest things I've created for the CR10 so far: a set of dovetail-style quick-connect fixtures for the OEM hot end and laser engraver. One can swap between printing and engraving/cutting in less than a minute. The reason I...