rat fink models

 This model is currently a working draft. Solar astronomy has inherent dangers, please be sure you understand these (see also below). Use is at own risk. More general information about this approach to solar astronomy can be found at the Sol'Ex...

We are presenting a new wind turbine device, that is easy to 3d print, it can be made handcraft once it is viewed it components and how they get assembled in a very easy and intuitive view, This system have several pending patents and the device...

Generate and print your own, compatible with any existing threads!This model was designed in Fusion 360 and uses 3 required input parameters and standard Metric thread profile equations to generate a cap that will perfectly fit any of your threaded...

18-48V AC/DC voltage models are available for network systems and marine vessels. We also offer an additional 347-480V high voltage, 125-250V DC, and 0-10V dimmable versions of this explosion proof LED light fixture.Mounting: The EPL-LED-150W-RT...

I got a package of 5 and when I opened them I found that the design had changed slightly and the material they used on the newer models was slightly thinner. The original clips were therefore a little sloppy. I adjusted the clips to fit the newer...

The first one was a box, with an RFID reader, that provided clues on its LCD screen and had a secret compartment that opened with a specific secret code. The second device was this Bocca della Verità with RFID in the mouth (it was a secret) provides...

It is essentially based on my first design.If you don't have an AC Infinity T8 or don't want to spent 120 bucks on one just to disassemble it, check out this simpler and cheaper...

Models intended to be part of the numbers node all begin with the prefix MMU. Card Compression Spring: if you have problems with the card compression spring lifting off from the bed, it is recommended you add a skirt of at least 6mm. Assembly Tips:...

UPDATE: 20.04.2022adapterplate (new design) for model C Hello, we would like to introduce you to our stealthburner conversion mod. At this time it works only with the klipper Firmware. The use with “Marlin” is planned later and will be...

35mm diameter)Electric cablesElectric soldering iron and solderAn M4 screw with its corresponding nut (approximately 15mm in length)Two appropriate screws for fixing the DC motor to its support (depends on the type chosen)Instant glueStep 1: Print...

The models in these STL files are scaled for a 58cm head circumference. (Refer to photo of T800 for how to measure the size you will need to print) Just scale in your slicer software on XY by 1/58*[your figure]. Do subscribe to my YouTube...

 It is recommended to use MERV13 or higher for virus carrying particles. The fan is a Black & Decker 9in Mini Box Fan, Model BFB09W*.CostAt the time of writing this the total cost is the same for each of the 3 versions as the different...

I increased the version numbers to reflect this, but if you already printed them you don't need to reprint because there were no actual changes to the models. - Added drop-in boxes to fill with cut-off 12in bamboo shish-kebab skewers, to allow for...

This is a model and instructions for how to build your own fiber optic light engine that is smart and can be controlled through google home. This version uses a smart LED light bulb as the source of light. It can use any smart light bulb that is...

Extending the print head cable on this model is not unheard of, it is a common change made when upgrading this printer to a direct extruder. The portal cable (black) does not need to be extended, even for the extension kit for 50mm, as long as you...

... into a new weapon. By Alex Wellerstein, a historian of science and an assistant professor at the Stevens Institute of Technology, in New Jersey. Attributions: •Screwdriver by user DAPE, Cults3D (under CC-By-Sa-Nc). •Demon Core modeled by Szadros.

The springs I upgraded to where Integy RC Model T8087 Progressive Spring Set: https://www.amazon.com/gp/product/B00W3ZCX00/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1 They are a bit longer but will allow for some preload tension if you want. The...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_mirror = 0 stencil_drawing =...

Able to hold 1 stack of cards and 2 columns of hexes. --4-2-17-- Added player card 2.2, a little bit smaller on the separator pieces that come off the model, should be easier to fit in the box. --4-2-17-- Removed older hex and cards .stls and...

If in doubt refer to Mehdi for more demonstration material.I was basically trying to address two "issues" of my Anycubic Vyper:The PSU and Mainboard 24V fans are very loudI want to upgrade my Vyper with an OctoPrint/OctoPi setupSo here is my...

IntroductionThis model provides an effective, low-cost teleprompter for livestreaming and recording. Using a Raspberry Pi and Pi Camera (the cheap, non-HQ one provides great full-HD video in this application), your phone to display your script or...

My model was FDM printed only. Actual code will be available here: https://github.com/Kandzior/NeverHotTeaAgain Charging is done by plugging micro-usb cable to the charger module through hole at the side. When you disconnect the plug, you can cover...

If desired you can secure it in place with a sticky pad or some hot glue. Push the insert into place. Lower the NeoPixel Ring into place, ensuring to route the wires through the slots in insert. If you are using a diffuser, place it on top of the...

Both uploading and downloading a few dozen bricks is a pain :) However you can get all: STL.zip contains all the blocks I made so far STL-sets.zip include multiple brick sets for printing (difficult and not so often updated !) source.zip...

 Foam card (if you're not already familiar with it) is a material used in the art world and in crafting or modelling situations, a layer of foam is sandwiched between 2 layers of card, the resulting material is incredibly strong and is generally...

The assembly is not complicated, for each configuration I put exploded photos, pay attention to the insertion of the brass threads, (there are 2 models you need both), and to the direction of insertion, those placed in the attachment of the guides,...

Check out the Raspberry Pi 3B+ here: https://www.raspberrypi.org/products/raspberry-pi-3-model-b-plus/ The controls are simple but there's enough buttons for most games. D pad for direction control and 4 front buttons provide your basic SNES type...

No special settings except for the optional color change.I suggest setting also the infill and supports angles to 35 degrees so it matches the angle of the parts.If you also want to print the letters on the cover you can use the MMU2 (or equivalent...

The original interior geometry from the Prusa filament sensor has been incorporated into this design, sourced from Prusa's models. The pinda is in the same location as on the original. The nozzle in this new design sits 10mm further forward along the...

...I propose some activities to do programming this robot: First goal: Making it move The first and basic activity could be to program and model their movement, to find the correct position sequence for each leg for a forward run. First step: assembly.