replicator 2 extruder replacement 3d models

Bored about this problem (I replinted 4 or 5 extruder mods) I decided to design an easy and cheap way to replace the extruder with same printing results as a new extruder mod but with no deformations due overheating. I bought a plunger from...

Cut one bended part of the clothespin to fit it in the extruder back piece and bend the other leg a little nearer to spring to adjust the turn radio (in my case 2-3 millimeters are enough). Put the smallest piece into the bended leg of spring and...

Our old Replicator 2 Delrin Plunger head was getting very worn so while waiting for the next extruder upgrade to arrive, we designed and printed out a replacement head for it. It still makes use of the stock screw and rubber o-ring. ... Instructions...

... fan hub with the sharp knife, glued new propeller on top of old fan hub with couple of drops of cyano-acryllic glue. It works again! As an addition - printed new fan cover as a replacement for old metall cover to protect fan. ...Good luck

... Instructions I printed this: infill: 100% Layer Height: 0.25mm Shells: 0 Feedrate: 100 Travel feedrate: 150 Temperature: 230 Print four of these. Stick the 40mm round felt pads on them and put them on your makerbot replicator 2.

This extruder upgrade for the Replicator 2 replaces the Delrin plunger with a pinch roller. Using the spring specified in the parts list below, this pinch roller provides about 60N of force on the filament, which provides enough driving pressure on...

This extruder upgrade for the Replicator 2 replaces the Delrin plunger with a pinch roller. Using the spring specified in the parts list below, this pinch roller provides about 60N of force on the filament, which provides enough driving pressure on...

My Fan Blade Broke while doing some maintenance for my Replicator Dual Extruder Which fit with replicator and replicator 2x and replicator dual and many other printer it is kind of not easy replacing it but any way i uploaded the files for who want...

... --> PLA was not always taken by the extruder. So I made an adjustable extruder to solve this problem. You just need a M4 bolt, a M4 nut and a little spring. All the rest is like "Replicator 2 Drive Block" Instructions Print it without support

Instructions REPLICATOR 2 - 100% infill, high resolution - Printing time 15min. Get rid of the blades and slide the prothesis over the fan zylinder - smale pieces of the blades will help to fix it! (i guess) can´t test it because i will wait for...

I recently blew out both extruder motor stepper drives on my Makerbot Replicator Dual Stepstruder. I won't go into the reasons why but wanted to show my repair. I don't think Makerbot sells parts for this unit (at least doesn't show them on their web...

Petite erreur de jeunesse: Une pièce qui n'aurait jamais dut casser qui casse sur ma Replicator 2. Un peu de sketchup, et c'est partie! C'est réparé et fonctionne parfaitement, preuve photos à l'appuie. ... ...

... head, so I don't know what it should look like. Instructions If the same happens to you, loosen and remove the old one and slot in this replacement in from below. ...I've included the model for anyone with Alibre Design that wants to play/improve.

I modified this model using Solidworks 2017 student Edition. ...Also attach for all Solidworks parts. And i modified this extruder for soft filament.

After installing the 3in1 Extruder Upgrade I wanted to get rid of the roof overhang / filament guide tube holder so I downloaded a few fan brackets with no joy upon install. With the few I tried I noticed that the cooling duct was not properly...

This is a conversion I did for the MakerBot replicator 2 extruder. ...I was having problems with the standard extruder feeding system so I purchased a Bulldog extruder and then I designed and machined a mounting plate, and eh presto I now have no...

If you have issues with your filament tube coming loose from the extruder of your MakerBot Replicator 2, download this. Put it between the filament tube and your tube holder on the extruder . ...This simple fix saved me hours of lost prints.

This is for or those of us who have ditched the plastic tube that guides your filament but who want to reinforce and guide the filament to your Replicator 2 extruder. ... It fits into the hole that the plastic tube was in and snaps on the right hand...

Works for the replicator 2 extruder, though I assume the hotend assembly is similar for other types of replicator? Note: You will notice on my printer the tape is not quite long enough. I've updated the file to fix that, this template should be...

I got my hands on a Replicator 2 and the MightyBoard Rev H with a missing botstep and 3 blown BOTSTEP17Es ($50), so I went the Pololu 2128 S4988 Stepper Motor Driver, Black Edition ($6.95) with the 68mΩ sense resistors, which is the version made...

Still using the factory extruder block for the Replicator 2? Paranoid you may not have a replacement when you need one? Print a few of these and worry no more! They fit the extruder like the factory derlin piece. Worth having a couple handy in case...

Recently I noticed my Replicator 2 was not feeding the filament properly even with the "free" Makerbot extruder upgrade. I performed the pinch test as the filament was feeding through and noticed that I was able to stop the filament from feeding. So...

... fit the new blades onto the fan assembly. Yes, while I was printing this I didn't have a fan going, but it's a short print and aftwards you will be back to 100% functionality. I printed in standard resolution on a Replicator 2 with Makerware.

After losing one of the original feet from my Replicator 2, I decided it was time to draw up a new set. I decided that instead of maintaining the small footprint of the original, I would give it more surface area, hopefully eliminating scratches on...

I got tired of keeping track of that little 2.5mm hex key and designed some thumb knobs that would be small enough to maintain my OEM look and function, but have enough grip to securely torque together the extruder assembly. Instructions After a few...

For those of you who have accidentally put your tool into the blades of the extruder fan... (Pause for laughter)... I made this retrofit fan blade design. ... I'm using it now and it works great.

... the screw is more solid and the arm doesn't warp the PLA base. i've put also a small m3 washer between the base and the arm, and taped (kapton) the extruder motor between the motor and the extruder base to keep lower the temperature. ... Have fun!

... screw nut and o-ring. I'm still using the stock plunger, but I'm tearing through printers looking for single metal ball to replace it. Thats a 340mm whpthomas profile print. First one off the plate after reassembly. ... No adjustments necessary.

Instructions Replicator 2 Extruder Wire Bundle Strain Relief Upgrade = R2EWBSRU 1) Print this R2EWBSRU (6 minutes) 2) Peel back the black braided sheath and slip all the extruder control wires through the open side of the R2EWBSRU 3) Seat the...

Modified swing arm for Replicator 2 extruder fix to fit 605 bearing. Source included for easy modification for other bearing sizes. Instructions This is just the pivot arm. Print the fixed arm from...