retro rocket ship 3d models

The model formed in our minds is based on what we see, and the brain completes the rest, including hidden features. So, I set off to design the object using Fusion360 and test it. I created several versions of the lock inside the object, but this one...

Just drag the lithophane (standing up) to the mount, and position it so that it intersects the model, while lining up the curved edges as seen in the picture. 3. While that is printing, disassemble the nightlight by pulling off the diffuser,...

i started with using an other Model as base and didn't check the dimensions 2. i realized my mistake to late XD 3. if i change the scale i would have to split in 3 parts because it would to long for the most Printers 4. i'm to...

The sourced parts needed are the same than for a MyRCCar OBTS Chassis, so you can use them in all models by now. This means that you can reuse existing parts from other projects, making it easier and more cost-effective to build this chassis. If i...

READ BEFORE PRINTING!This is a non-commercial print, this means you are not allowed to sell files or prints of this model.______________________________________________________________________________________What is this?A modular tripod/handle...

This is resistant to everyday wear and tear, but we got warned that rust stains are not completely removable.So a stainless clothes drying rack became necessary.Most commercial ones just have powder-coated steel tubes which rust after some...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8 custom_top_port_corner_radius...

Modeled after a 1915 candlestick phone, early versions had no dial because you just lifted the earpiece and clicked the lever a few times to get the operator's attention and told her the number or person you wanted to speak to. This is a fairly good...

If you want to save time while testing, you can print the included calibration test instead of the full model, but that is optional.Once the egg halves are printed, screw the threads in and out repeatedly to remove any stray particles. It may feel...

Description: https://youtu.be/G9-N-nIqc4g Assembly: https://youtu.be/2hdSGDdjpeQ Torque Capabilities Please note that I designed this CVT for a demonstration model, it's not intended to be used as an actual transmission. How This Works - Watch the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

It's corrected in the download-model.I know, this LCD knob is completely over-engineered and basically totally nonsense. But it was fun to design it and bring it to work for the LCD knobs contest.Triggered by verny's Cardan Joint Knob I thought I...

Rafts: Doesn't Matter License The "Sidewinder X1 E3D Hemera FFC Riser" models (.stl) are licensed under the CC BY license by Code and Make. The "Sidewinder X1 E3D Hemera FFC Riser" code (.scad) is licensed under The MIT License by Code and Make. As...

There is also a reverse mount for the hygrometer that's for mounting it on the inside of glass (also fits stock model).The hygrometer has an extender for the button that switches between C\F. You will need the original rubber insert...

the better the less likely it will grab but u can always use nuts on the other side even tho i didnt make a place for them to sit on the model since i had planned on using the threaded inserts but it will still work cause thats how i test fit...

It does not matter which direction is taken.Continue running the line down and up between the pieces through different holes until it is fully connected.The line must turn a corner on the bottom piece, so ensure that it is placed completely in the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

Here is what I came up with: This model consists of 3 printed parts. Then you need something with ø3 mm diameter as an axle. Anything like a wire or nail would do. Just cut it to a length of 18 mm. Fix the lever in the holder with this and make...

It was just hard to get some of the screws in it so I had to manually remove the parts this model has removed for you. Make sure is you use screws to hold the bearings tight that the lowest ones have low profile heads or they will be lower than the...

Use "leveling_test.stl" model to test auto-level accuracy. I made some work tests of this firmware but there still could be bugs there, so use it on your own risk. Enjoy! :) Update 1: My Start and End G-codes in Cura working well with this...

think about it like drawing line art, not solid modeling shapes in CAD). 6. Print with a layer height of 0.25mm or less. Much more than that and the slight bulge on each layer will grab the dough, making it harder to demold. We used 0.2mm layer...

Print so that the models are standing upright, largest end down. <h3>Post-Printing</h3> <p>To disassemble the original turn signal, follow these steps:</p> <ul> <li>Remove the screws securing the lens and remove the lens.</li> <li>Remove the...

I could not find caps / hoders which suited my project, starting from inspiration of certain models existing in AA, I made a design under fusion 360 which corresponds in the size of integration, as well as the possibility of making spot welding. ...

New version available: Please check out the new Ultra Flat Filamentholder model, now updated to be 8mm lower, more accurate, and faster printing :)\nFeatures of the Flat Filament Spool Holder\nJune 6th - Finally finished making it. Enjoy...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_back_camera_x_position = 0 custom_top_port_corner_resolution = 8...

[Medium Sized Model - 25mm Base] [Presupported in 32mm and 75mm scale]   One of the few Colossals on Tharador not to be born in the bitter Frozen Wastes of Oldavor. Harmara is also one of the few hemomancers to exist out the bounds of Oldavor, the...

These are mainly meant for kitbashing digitally, so they might not work with existing citadel kasrkin/cadian models without a little work. For torsos I suggest Planetless Trooprs by LoggyK, these were the main inspiration behind the packs. Storm...

The first number at the end of each model's filename is the size of the PVC post that the adapter is intended to go on top of, the second number is the size of the PVC pipe that the finial would normally go on. I have a collection of Halloween things...

If you like & use my models please consider supporting my efforts with the button below. Thank you!…Please be sure to hit like & post a make, I'd love to see your prints!The Vortex series grows with Gemini! Print faster with crisper cleaner looking...