scope phone adapter 3d models

This is a remix of https://www.thingiverse.com/thing:4696157 CHANGES: Adapted outer diameter to 24mm laser gauge Added holes for 4x M3 screws that help align and fix laser in position ORIGINAL DESCRIPTION (with editions that apply): This is a...

If you have any problem, please send me a message with the size of your stack of coin, I will adjust the box to adapt to your need! The test coin for the $2 use as the full box a stack of 8. ...As there are 15 and was lacking space, the $2 is...

Portable Yagi Uda Parts ================== I used these parts to build a Yagi Uda based on M0UKD's design, but these bits can be adapted to any design. M0UKD design is published at: ...

The design can be adapted to other printers by doing a new base mount for the base and sliding parts which stay the same. To assemble the mount, you will need a 1.375" long 4-40 screw and a 4-40 nut to create the lead screw. The mount is screwed to...

-The Clamp holder A/B was printed with adaptive layer heights in prusaslicer for a smoother surface on the curve part. (higher resolution on the curve area, lower resolution on the not so curve area) -Watch out for elephant foot when printing the...

- You'll find an adapter STL file to mount a 160mm tube onto a wall with a hole of a european standard brick size. - Printing: I printed everything in 0.25mm layer height and used ASA filament because my use case has some higher temps. UPDATE...

It is recommend to cover the inlet of the blowers with some tape or use the 7mm blower to CPAP adapter, if you can blink a lot I would recommend the 10mm. I'm working on a different version that will have adjustable airflow, just putting this here...

> 2 x 20mm long m3 screws and nuts (preferably one 25/30mm m3 screw to fixate the nuts, see included photos) > 1 x 28byj-48 5v stepper motor > 1 x A4988 stepper motor controller > 1 x Wemos D1 Mini (I've tested NodeMCU V2 and V3 aswell) > 1 x...

For my setup I am using: Long version frame \250mm top and bottom plates\; B19 cheap fpv camera(19 mm) + TS5828S 600 mW VTX; Motors - T-motor F40 pro III; Props - Hurricane 51433-3; Jhemcu 40A 4 in 1 esc(30.5x30.5); Holybro KAKUTE F7 Mini V3 (20x20)...

This print reuses the existing camera shaft in the Logitech C270, so all you need are 4 M4 V-Slot nuts (or 4 nuts with the 3d printed V-slot adapter) and 4 12mm long M4 bolts. - I wanted it to be compatible with most 3d printers, and it is...

I used a smooth/wipeable melamine faced furniture board) 580mm x 450mm x 18mm, QTY 1 A Spool of PETG ,QTY 1 Some PLA ,QTY 1 EiBotBoard, QTY 1 9V 1.5A AC/DC Power Supply Adapter 5.5mm x 2.1mm Pen Holder, QTY 1 Precision Hardened Steel Smooth Rods...

If you want to buy everything yourself, here are the parts: And here's the build video: String [1](https://www.amazon.com/gp/product/B071G2F3LK) Zip Tie [2](https://www.amazon.com/gp/product/B06X6KGKWQ) PTFE Tube...

Mass statistics: Standard RunCam HD w/ nano->micro adapter & cable = 5.56g Printed body w/ sensor, CaddX lens and cable = 8.98g And since the lens itself is a 2.08g premium (RC: 2.52g v CaddX 4.60g) the body is only a 1.34g premium so on your...

I just found the pre-built module easier to set up as it does not require any extra parts and is powered by a standard micro USB adapter. AD Module: (AliExpress) HX711 Load Cell AD Weight Pressure Sensor AD Module with Display 24-bit Weighing...

Server Components: - Raspberry Pi - External HDD x2 - Powered USB Hub - Cables to connect everything Fixtures are created to fit the following items: - Raspberry Pi 3B - [Powered USB...

• Print the fan duct at .2 and use adaptive layers for the best success. • The fan duct should be printed in ASA since it sits close to the heat block. The other parts can be printed in ABS or PETG. Installation Notes ----------------------- ...

So I went to work designing an adapter/mount and that worked fine (posted that in his remixes if interested) but I noticed my handbrake was falling apart from the hard use and I wanted some new features/updates that his handbrake didn't have. So...

- 5x M3 6mm screws for the motherboard, if you want it secure in the case - 2x M3 screws, 6mm or so, plus T-nuts for the sides, if you want it to sit between the extrusions instead of falling on whatever surface supports your printer - Micro SD to...

If your enclosure is larger than mine, I have included an adapter to stack a second heater. If you stack a second heater, you will need a second power supply and a second mosfet module. You will be able to use the second relay on the relay module...

It was adapted into an anime television series produced by Kitty Films and broadcast on Fuji Television affiliates from October 14, 1981, to March 19, 1986, with 195 half-hour episodes. Twelve OVAs and six theatrical films followed, and the series...

For the power inlet I used a power jack adapter You find them on internet routers, USB hubs, scanners and other low power devices. I usually salvage these parts before throwing old hardware away, so I have a bunch of them. The power connector is...

You'll need to adapt if you are running 220V. Here's what you need: 1. Inkbird ITC-100F temperature controller (https://www.amazon.com/dp/B00OXPE8U6?psc=1&ref=ppx_yo2_dt_b_product_details) 2. 110V AC heating element with fan...

This adapter simply plugs in between the bearings. Voila, fits all sizes of spools. - <b>Cable tension reliever</b>. The X1 uses some very nice ribbon cables, which however, tend to snap close to where they attach to the extruder (must add...

Furthermore, the software used to create g-code, Inkscape, is opensource as well. Many thanks to the user JuanGg whose pen plotter project was a great inspiration. Build of Materials Dimensions are for the A4 version 2 Nema 17 Stepper Motors 1 SG90...

Nor can you have that USB hub near the SSD, in fact you can't have any active wires near the SSD's adapter chip, not even the wires for the LEDs. I suspect if I ever try to boot it with the analog out port enabled I'll have to move it too, that's...

I have started a Moai 130 to 150 project and this is an adaptation of a PDMS vat for those that want one using a 1/8 inch to 3/16 inch glass window instead of an acrylic window. The vat is designed wide enough to not need shimming and hold a healthy...

The disc fits the NIDEC with the M8 adapter purchased on microcutter. I also designed a new protection to keep fingers and cats as it is in my case away from the blades. It is inspired by the one found in Liam 6 but slightly larger and the holes for...

To help facilitate additional tool mounts, I have included a blank dovetail adapter as well. The pen mounts by design may work for a large number of pens. For hardware all bolts used are standard M3. M3x12 for the latch mount screws. M3x8 and...

## Non-source-code media - Creative Commons license (Creative Commons BY-SA 4.0) Please see the following link for details: https://creativecommons.org/licenses/by-sa/4.0/ You are free to: Share - copy and redistribute the material in any medium or...

These are designed a little differently and I had to adapt the housing. The small bars on the housing fit into the recesses on the underside of the controller connector. They should hold the plug and prevent the contact pins from slipping. But since...