serial experiments lain 3d models

It warrants an experiment but in the meantime, I recommend a brim on everything.After testing, I had the best luck with the same three rotors that worked best when paired with the other horn also. These were the 5.6, 5.1, and 4.6mm inner cone...

To be honest, it will be a little cheaper from buying the official enclosure from Creality, but to my experience, it will be a lot better. If you are still on it, I can assure you, this thing is sturdy and practical as hell! What you need to...

The height is directly related to the “overlap” of the squares, so even loose puzzles won't fall apart if the height is large enough.Don't be afraid to experiment: if you break something or encounter an error, just re-download the file and start...

(update: after much comparison, the alternate horn definitely works better!) For another experiment, I super glued two of the larger inner cone diameter rotors together and aligned their slots properly with a couple pieces of filament while the glue...

If you prefer, you can use a “full spectrum grow LED bulb”, but in my experience it is not giving you the expected benefit. In most cases these are just red and blue leds put together and the naming “full spectrum” is a bit misleading.</p><p><a...

NOTE: By doing several experiments, I noticed that for some PLA filaments it is advisable to lower the Flow rate to 88% directly at the slicer level, in order to obtain a perfect first layer. In addition, I have also reduced the flow rate of the...

Researchers have long been fascinated by its ability to process vast amounts of information, learn from experience, and adapt to new situations with incredible speed and agility. Despite decades of research, however, the full extent of the human...

If you did not remove the waste as I told you, it will remain attached to the worm cast that you are still holding and can now be pulled off the extruder before the printer resumes printing.Repeat until the print is complete.Tip: You can save the...

Straight bevel gears experience a common problem with straight spur gears when each tooth engages, causing an impact due to… щ assistant In bevel gears, teeth can be straight, spiral, or hypoid. Straight bevel gears share a problem with straight spur...

There should be room to dock at least two, and perhaps three [E3D ToolChanger Tools](https://e3d-online.com/products/toolchanger-tools) in the back of the MC350, this would allow experimenting with the E3D docking system in a framework considerably...

This configuration file contains the necessary settings for the macros to function seamlessly with your printer.Experience hassle-free printing and say goodbye to nozzle contamination with the Nozzle Brush. Get yours today and enjoy cleaner and more...

 Don't try to continue a print that is going badly, you can end up damaging and having to replace the hot end, or worse.Possible additions (coming soon):  Currently I am experimenting with arms made from heat-shaped PVC pipe, there are plenty of...

However, in my experience printed surfaces tend to be very light and reflect sound surprisingly well and the enclosures I built using wooden side panels seem to sound significantly better than the ones with printed side panels. <b>UPDATE 08Dec20:...

With his many years of experience with visions and spiritual journeys with the Blood Serpent, he could suddenly feel a drop of Anima. He was close.  He spent many days trying to come closer to this Anima Aura, most of the time without luck. But...

The Start Arrow can be a little tricky so you may need to experiment here with what is best for your setup.For the most part, you can print everything at 0.2 mm layer heights. Infill is entirely up to you. You shouldn't need a brim/raft for any parts...

So I was able to run it for about 6 minutes with hot water and a negligible/acceptable amount of water was leaking out and spraying back towards the wall, Based on this experience, I think the smaller adaptor will work just as well as the bigger two...

My experiments have established the following experience: The first thing i found out is that the head of my pump is definitely larger than the border of my sink. The second thing i found out is that if i raised the end of the tube above 1.4 m above...

He has spent a lot of his own time cleaning this frame up for you guys, to ensure that you have the absolute best experience with this Warbird.. I believe it deserves a great deal of appreciation from the community, especially if we end up posting...

I'm still experimenting with rod ends, but for the moment I have capped the ends of 10mm carbon fibre tube with hot glue and used a piece of cloth between the rod and a 14mm steel ball bearing. Another option would be to glue a short piece of snug...

I am going to be working on and experimenting with a direct drive version of this kit, which will be for a BMG style extruder and 4023 "pancake" motor. If interested in that, log in and post a comment here and I will let you know when it is done and...

It's not a big deal, in my experience. There is a separate travel box, made to be put in one of the expension boxes, for the purpose of taking the game with you, and that IS flip-proof. Speaking of which... there is now a travel box! Instead of...

As time advanced, the introduction of many chemical materials made a long history so many different types got developed alongwith several variants.\nThe major reason to replace old method in production is because the use in car and aircraft for tyres...

HyperCube parking extruders I wanted to experiment with multi material designs for quite a while and after many failures I ended up with this. I didn't yet quite achieve printing in i.e. multiple colors (I'm working on Slic3r configuration for that)...

I had just recently treated myself to a new iPad Pro so I could play with Shapr3D, which promises a new experience in 3D design, something I have struggled with in the past. So I based this design on a mockup I did of the parts that I had: ...

In my experience, practically no coarse dust and about 5% of the fine dust gets through which is still enough to clog the filters over time. Stage 2 comes to the rescue! Technically this design should achieve a better precipitation than stage one by...

Unfortunately, I cannot give you support for this software because I do not have any experience with them. The only software that I support is Maya, Unreal Engine, and Unity. My customers have reported to me that my models work in Blender. Can I...

... cells. You may need to then right-click on the "Body" tree item of the part, and select "Recompute object" to update the model's dimension as edited in the spreadsheet. Experiment, have fun, and let us all know what you've created! ...

I am not affiliated with 3D Gloop but have experimented with different glues for my models and have found that this glue is a great option for my models. Each type of glue has different pros/cons and I found that 3D Gloop was far easier to use than...

I strongly encourage you to play with these angles and ratios, preferably in a local installation of OpenSCAD working directly with mikey.scad rather than in customizer; you should have a better, faster experience exploring the models that way. I...

Eventually, I plan to experiment with a small battery charging off the cells to power through tree shades along the road in my neighborhood. It controls and drives quite well and is not fast, but the motor is geared for torque, not speed, which is...