smithsonian 3d print files

BASIC PRINTING INSTRUCTION FOR EACH PART ARE IN THEIR NAME FOLLOWING THIS LOGIC: [model name (base if common to most][part name][helpful assembly info, mostly left or right][ (need support) if needed][how many are needed if more then 1] Unlike my...

MegaMAME is a large console which can be stood on a table, or you can use the stand to hook it over your knees while sitting on the couch :-) I had to split the case into two parts to be able to print it on my Ender 6. I'm happy about how it turned...

Feel free to download and print it yourself - total cost under $30, plus your time. I tested this monitor using a tiny whoop's 260mAh lipo battery, which lasted for half an hour. With over 3000mAh Li-Ion batteries, you can expect an operation time...

I also made the spacer shaft shape wider so it is not as hard to print, nor as fragile to handle. I also eliminated a few of the sizes that I felt were not necessary. --- This is a PPC (Pixel Pipe Clip) spacer tool that will help you accurately...

If you're not using a hole that has been cut, then there is a cover so your nutrients don't get light.Use a 51mm hole saw and you have a water filling hole and a hole for the water level gauge.General printingEverything is aligned for printing...

Last but not least, tighten the fitting tightly (this will press the inliner firmly against the nozzle.Without filament, heat up the hotend, put on the nozzle, let it cool down and print until the doctor comes. ...Of course, don't forget the bowden from...

This allows it to be printed standing on its side with less support. With no supports, the top will have some drooping/stringing and some cleanup of that will be required. With supports there may be some residual support cleanup required. I use...

Note on pressure booster: The wings is only one wall thick so make sure to use "Print Thin Walls" in Cura. How to measure static pressure: https://www.thingiverse.com/thing:4401775 <h2>2020-12-10: Minor update</h2> Reinforcement at coupling...

EN Translated with www.DeepL.com/Translator (free version)&nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; When printing, observe the direction of the parts on the tray&nbsp;Assembly order&nbsp;1 Place the 4 nuts (M3 square) in their housings2 Pass the...

(Print "FrontPanel_input_noSCART" instead of "FrontPanel_input") If you connect Component or VGA, you can use a SCART breakout to pass through audio in a clean way, without ever having to swap the plug on the back. Last, you'll need 8mm M3 hex bolts,...

I printed the case parts on my Auxiliary Sidewinder X1 in PETG with a 0.4mm nozzle and a layer thickness of 0.2mm. Attention: Due to the life-threatening electrical voltage only persons with appropriate qualification should assemble and use the...

I'm waiting until I have all of the parts printed for my new printer I'm building before installing this upgrade on my printer. When I do, I'll create detailed assembly and installation instructions. Here are some instructions if you want to try...

Besides, the design provides a high creepage distance on its surface; however, FDM prints tend to have fine fissures that might compromise the insulation. Especially if the part is contaminated with conductive dirt. Resistors have distinct voltage...

This model is approximately what we saw it can be printed in two halves and glued together. We both agree this is extremely close to what it looked like. Klamath Falls is home to Kingsley Field, the 173rd fighter wing, a F15 and soon a F22 base which...

It prints quickly, uses only about 1 gram of filament (0.33 metres of 1.75 mm filament), and is very easy to use. It clips onto the spool of any brand of filament, so it's a universal clip. It can clip onto 1.75 mm filament or 2.85 mm filament, so...

#### What you need * The three printed parts * A cheap green laser pen like [this one](https://goo.gl/8AaT9K) (others could work the same) * 6 x M3 screws (I use 16mm, I think 12/13mm is great) Cost: less than 5€ .. Not bad ;) #### How to use it ...

If you print it, please post a make with pictures of the end result! Thank you! For all Ender 5 and Ender 5 Pro users! By now you probably have your crappy landy power supply clone swapped out for the Meanwell LRS-350-24 power supply! So now you got...

(hence the name Duo, eh?) Addition parts you will need. 2 - 808 (MATEcam) cameras - either a dissaembled keychain version or the DYI version (here are some links)...

Using an M3 tapered tap, I found it was relatively easy to slowly do this with no pre-drilling.The thread will, of course, not be complete and that is why a long screw is used in fixing.Assembly:Two M3 nuts should be pressed into the back of the...

This is a little bit tricky as you may not touch the PLA printed support with the hot solder iron, and the space through the spokes of the outer support rings is quite limited. At last, mount the Nd-bearing magnets onto the axis. Use the hülse.stl...

In using the shroud while printing a model that takes up the entire bed, I found that the wires from the extruder need to be routed over the output end of the fan using wire ties, as shown in the new picture above. As I'm using a low-velocity fan,...

Print with layer height 0.16 and 20% fill.&nbsp;If you like my designs give me like and share. If you like them a lot invite me to a coffee.</strong><br><br><a...

FR Tournevis compact avec chargeur 8 têtes à rétention magnétique. 1 aimant cylindrique de 1 cm x 1 cm est indispensable pour le fonctionnement du stockage intégré au manche l"aimant est en contacte avec la base de la lame porte tête ce qui permet...

Font Narrow Widen = No widening of narrowed characters, a setting from older designs where letters may need expansion when space runs low so as not fill too many vertical spaces in tightly stacked horizontal text columns across page; it reduces size...

So that fits best.DO NOT PRINT IN PLA! PLA can't withstand the summer heat.</p><p>&nbsp;</p><p>#############################################</p><p>Ich mochte den originalen Becherhalter für meine E-Klasse nicht, also habe ich mir einen eigenen...

I also appreciate pictures of your prints too. Thanks ;) NOTE: A new V5 lightweight and mini version is available from: https://www.thingiverse.com/thing:4850894 LEGAL DISCLAIMER: This device is designed for adults. Long term wear can suppress...

EDIT 01.07.2020: Added a foot to be printed in TPU, one for each corner. Holes are already drilled into the case's bottom; use M3 screws to secure them. This is a fully self-designed BT-Speaker setup that you can download and edit as you like. A...

Fishing the wires through the print is a little tricky but not difficult. Longer screw is for the battery latch and sandwiches all parts of the adapter together for strength. I used flat head socket screws since I had them, but any flat head M3...

The play translates into uneven surfaces which are readily apparent on large flat horizontal surfaces, but also affect every other print in some way. There are a few mods here and you can try all or one at a time. First off, the bearing holders on...

I used the #19 drill with the depth stop (as described in the Ford Flat Head Assembly Structures for the threaded inserts) to drill holes for the magnets in the block. The Display Base was too big to print as a single part on my printer, so I split...