soft lines 3d models

If you got creative, you could probably use fishing line or something similar to tie the two together through this hole after assembly. + The GPS antenna holder was designed against my board, and the little notch is supposed to "clip" underneath...

 Wrap some masking tape around roughly where you want to make the cut - this will make it easier to mark, and will help to keep the edge a little stiffer when you are cutting it.Find an object that's about the height of where you want to cut,...

It's hard to line up the circuit board properly, but if you're unsure, just take the Battery Holder and Cover piece out to get a feel for where it goes. Once both pieces are in the Base, if the circuit board doesn't seem to be aligned, you can use a...

The 240V power circuit works in principle so that the built-in relay of the SONOFF DIY switches one connection line, and the switches of the additional relay board switch the other connection line(s). Assembly: The cut-outs are of different widths,...

0.3 mm layer height should also work well. Since the lid and the outer box have a 3 line wall thickness, it is recommended to the switch on the advanced option detect thin walls, this will speed up the printing process, and should result in a nicer...

I used prusa slicer for this and it worked well in my favor to keep print times down, but print strength high. Post-PrintingStep 1: Joining surface sanding After printing everything, start by sanding all the joining edges to a flat, rough finish...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: phone_model = 3 custom_top_inner_edge_chamfer_radius = .6 custom_top_port_corner_radius = 5 custom_back_extra_port_corner_radius = 5...

There is no try.The greatest teacher, failure is.For Light and LifeWe are all the RepublicEach phrase comes in two versions - Long is the entire phrase on a single line, Short is split into two lines.The doorhanger says “Do not disturb”. There is...

When they both show the same result in the middle, you have won!Design of the in-line springAfter the print-in-place cannon where I used a vertially printed spring, i wanted to also make a horizontally printed spring which doesnt break. Two...

Enable support on build plate only - some slicers will build support all around the outer edge, but you don't need this; I used an overhang threshold of 37 degrees with pattern spacing of 0.5mm and contact z-distance of 0.1mm and set XY separation...

I recommend not supplying this device with any kind of smart charger as some of these depend upon the data lines for communication with the device being charged. The 3D printed parts consist of three spacers for the USB connectors (two flavors),...

I removed them from this version. The rear ‘rubber’ seal should be printed in TPU. I lined the inside of the speaker with adhesive-backed foam tape… I have no idea if this helps, but it makes it look like I know what I'm doing.There is a...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 1 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

The 5 hub guiding lines are very tight (which is good) so print the hammer tool and place it on then hammer onto the hammer tool. The holes on the hub adapter are a tad bit to the right so I suggest using a file or drill to make a little more room. I...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_y_position = 0 custom_left_port_corner_radius = 5 custom_bottom_port_corner_radius = 5...

Single Line - A delicate choice for everyday wear, single line adds a touch of whimsy to any look. Mangalsutra Bracelets - A traditional symbol of love and commitment, mangalsutra bracelets are perfect for those who want to share their story...

Assuming your 3d printer is accurate, the holes should all line up. Make sure you have enough length on your fan cable to reach a nearby motherboard fan header, or see my note below in step 7 about using the built in fan header on the GPU. Step...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

Single Line #: Our single line bangles add a touch of simplicity and elegance to any outfit. With various designs and materials available, we have something that suits your personal style. Mangalsutra Bracelets # THe r jewelry types..... Men'S...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_back_camera_x_position = 0 custom_top_port_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_x_position = 20 custom_back_camera_corner_resolution = 8 custom_bottom_fillet_resolution = 8 stencil_horizontal_position = 50...

Glue the Sides piece to the Bottom piece putting a line glue all around the edge. Note that there is a right side up orientation on the Sides piece. The flat side should mate with the Bottom piece. Attach the Bridge to the Top piece using the...

TearNote that if your Y axis doesn't travel in a straight line, this part only addresses the symptom, not the cause, and your overall dimensional accuracy may suffer if you don't address the cause.To put it (slightly) more simplyIdeally the probe...

Single Line Bangles - Stand out from the crowd as you wear one of our classic single line bangles that speak for themselves. Mangalsutra Bracelets - Weave magic into your attire with our enchanting Mangalsutra bracelets, paying homage to cultural...

However, some patterns (such as 'Hole', 'Lines' and 'Hearts') may not print on vertical surfaces without supports.Following feedback that some users had issues stacking the caddies, the default Lip_Gap size has been increased to 0.6mm in version 1.4....

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 40 printer_tolerance = 0.4...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_y_position = 0 stencil_drawing =...

 Wrap some masking tape around roughly where you want to make the cut - this will make it easier to mark, and will help to keep the edge a little stiffer when you are cutting it.Find an object that's about the height of where you want to cut,...

This turned out to be something of a blessing, since it also turned out that my preassembled screens weren't mounted squarely, so even if the hole was the correct size, it wouldn't have lined up correctly with my screen. I ordered my boards...

This one file has ever laser cut piece for building a Replicator XL so you don't have to recycle parts and worry about which version you got and if yours will line up. It's also nice to be able to paint all your parts and still have your printer...