solid works software 3d models

All the juicy detail work is on the inside. The Babylon Project was beautiful to the eye, and yes, it’s a Diplomatic station. This isn’t. It’s a modular city for the Public by the Public.The inside is not hollow. It’s a city on the inside, the...

Running some medium or thin CA glue over the seam has worked well for me (do it from the inside of the case to keep the bottom looking good) Glue the nuts into the top panels with some CA glue. The nuts will pop into the holes on the top panels but...

Depending where you solder the wire from microswitch you have to change board.GP{number of GPIO}.Preflight check Go to Control Panel → Devices and Printers →  Right click Pico → Game controller settings → CircuitPython HID PropertiesHere...

For the launcher and the “motor” (= nozzle and adapter) you can find additional info here: https://www.printables.com/model/46571-water-rocket-and-launcher-platform-complete-instru These parts have been proven to be working (see old video). The...

Since these parts are slapping onto each other several hundred times during, even semi short, racing sessions.That's why i decided to design a version with enclosed magnets.After some testing on my own, here is a first version - a public beta, if...

It might come out a little nicer with the 2.0 Quality but speed settings work just fine. Using the TemplatesIf you are new or old to leatherwork you can use billets to add just about anything to a surface. These templates are for a ¾" strap and...

30_01_20 Uploaded step file for tool heads + base @ 100mm centres 10\02\20 Uploaded step files for the narrow version duct 05\04\20 Uploaded work in progress files for Base ducts for both Ender 3 & 5 which have all M3 brass inserts rather than M3...

You will find all available measurements in the following drawing:I created also an alternative set of templates for people in the US who are working with imperial units. Not only the corner radius is in inches, but also most dimensions are adapted...

The strap means that, once slipped on the arm, it is possible to open a bottle even if the hand using the device is completely disabled; all that is needed is for the adapter to be pressed on the cap and the arm turned to twist the cap open. I have...

I worked with Elana Wald on this project; you can find her clip version here (add link). Objective:With a partner, you will recreate your ghost clip using Solidworks.  You and your partner MUST have identical files that you create by collaborating on...

(Refer to photo of T800 for measurement)Just scale in slicer on XY by 1/58*[your figure] .Welcome comments and suggestions.Tip me a cheese burger and subscribe my YouTube Channel if you like my...

I used an X-Acto knife to remove it but a drill bit works too. The case screws utilize either self threading into the rear case standoffs or nuts depending on the rear case that is printed. Needed hardware: Case screws for self threading rear case....

For it to work with an external battery, a minimum of 6 amps of discharge and a maximum of 12.6v are needed, if you put more voltage it will burn. The Mini ZVS board has been modified by changing the 2 induction coils for two smaller ones and...

It still looks like it will still work but the focal point distance appears to be twice what I had expected... Thinking about it more, it is because I generated the array with a 12 inch focal point and then uniformly scaled the array up to 150% of...

Plenty of hardware parts can be sourced from broken devices.For example, I sourced my 8mm smooth rods from an old, defective, HP PSC Inktjet printer. Many inktjet printers contain such rods, as well as a lot of other useful stuff for...

This completes the entire construction and all that remains is to test the result of our work. To do this, it is necessary to place the hedgehog on an inclined surface with an inclination of approximately 10-15 ° with a sufficiently non-slip...

I have tested Yoyi and Zyltech TPU on my Prusa MK3 and both work wonderfully.When slicing vehicles you have created yourself, I suggest (when possible) orienting the print with the hole down, using zero or very low infill, and limiting shells to 1...

For a smarter version, the [Arduino Nano Every](https://www.amazon.com/gp/product/B07VX7MX27/ref=as_li_tl?ie=UTF8&tag=madewhatnow-20&camp=1789&creative=9325&linkCode=as2&creativeASIN=B07VX7MX27&linkId=f023c52e41204d7b8606cf475a7a14e9) is an...

......With the second ring, pull it like a nut.9) Cut the rubber pad for the concrete base from recycled rubber (it works better with scissors.10) Place a concrete base on a rubber pad (you can glue it).11) Put on the shade and it's done.   

Filament-RingStl-Files (without configuration)3mf-Files (with configuration) for MK3S and Mini Printfiles (G-Code) for MK3S and MiniScale the size according to the chart to print the correct ring size. Do not forget that the color change...

The front support must be flush with the front end of the base. WRIST REST ASSEMBLYSlot the two rest support pieces into the narrow, elongated holes in the base (left or right side) and press on the rest with the curved edge to the inside.You...

The printed structure could be accomplished with one or multiple rovers working in unison and alignment markers on three or four corners along with their rate sensors and accelerometers for precision building. As the rover lays each layer, only...

This product contains 23 parts: Base: 130mm Base (cut in 4 parts) Rock Terrain (Cut in 3 parts) Acid Victim 32mm Base (For Lotharius on foot) Dragon: Body Frontleg_L Frontleg_R Head Hindleg_R Hindleg_L Tail WingL (Cut in two parts) WingR (Cut in two...

The following image is the result:  The board works like the lid of the box also! You can also add some layer changes to the main body when printing if you like. This is why my board looks green on the other...

30_01_20 Uploaded step file for tool heads + base @ 100mm centres 10\02\20 Uploaded step files for the narrow version duct 05\04\20 Uploaded work in progress files for Base ducts for both Ender 3 & 5 which have all M3 brass inserts rather than M3...

- if you notice stringing you're too hot, better to go a little colder on this build and get fine lines rather than structural stability since the knife will not be stabbing anything or anyone (hopefully) Supports:YES!  Keep bed supports on only or...

I found that the best results came from printing as modeled with the outer face on the bed, then cutting off the extraneous parts of the tabs, followed by a little file and razor knife work to clean up if necessary. See image. Label Plaques: ...

  Note if you choose to scale it, the tolerances are very fine and it may not work on a smaller dimension - a larger one will be fine, you'll probably have to rely on glue to keep it in place.TEST FIRSTI usually stop the first print after a few...

They're working but the water starts dripping a little bit when the canister is laid down. They're also not optimised for 3D-printing.</p><h5>Purchased parts:</h5><ul><li>Soap dispenser (I'm using the “TACKAN” from ikea <a...

Love T-Shirts? Then you need to check out steps-per-mm.xyz! It is loaded with a huge range of wearable Parts &amp; Components. Please help support my work here on Thingiverse and on Instructables by using the following affiliate links when making...