split coupling 3d models

Right arm of Lord Commander Casymir, this lady-at-arms is an impeccable marksman and a passionate breeder of powerful war hounds, who accompany her in every battle.Trisha's past is painful and traumatic: it is said that in an isolated hut in the...

The robot has a ponderous gait.   PrintingGenerally I use a 0.25mm layer height and put about 1mm of plastic on the outside surfaces as a shell.  Since my printer has a 0.5mm nozzle I use 2 vertical shells and 4 horizontal top and...

(update: after much comparison, the alternate horn definitely works better!) For another experiment, I super glued two of the larger inner cone diameter rotors together and aligned their slots properly with a couple pieces of filament while the glue...

I've been using the sl1s now for a couple of days and the odors go out. If I'd do this again I would change the configuration so that (assuming CW1S on left side, SL1S on right side of the table) - Left and back side plastic panes would be static...

Let it cool and detatch, otherwise the magnets will damage the single layer they're sitting on.Once you have your mount, take the remaining 2 magnets and attatch them to the interface piece.Keep the piece handy and when it's time, take the 2 magnets...

I did this by rolling a couple drill bits in my fingers by only a couple of revolutions in the inner cone on the rotor. The two drill bits I happened to have used measure 4.75mm and 3.5mm in diameter. I removed a very small amount of material from...

This is a customized MK3S extruder called the Delta-P.Link to online 3D model viewer: https://a360.co/2BwxRKb Update 04/04/2021Fan duct completely redesigned:Easier to printBetter coolingRefined flow pathCFD optimizedEven cooling front to back...

Instead, the count took her as his lover.This made the countess furious at Arastacia and the countess had a bitter rivalry from that very moment.A couple of years went by, where Arastacia lived in the guest quarters of the castle, but she still...

It may take couple of tries, but there's plenty of extra blades in the cutter.Slide the blade into the plunger so the tip is about 6.5mm from the end. Depending on how well tuned your printer is, It may help to insert the blade's sharp end into the...

Finger-tightening the insert is sufficient and I put a couple of notches in it so that you can use your fingernails to aid in tightening and removing. Snug the ring down only enough as is needed to create a seal - don't crank it down too hard as...

Theoretically this distance should be the combined 2 radi of the pitch diameters of the two gears, however in practise, the actual proper distance can differ from a few fractions of a mm to a couple mms, due to manufacturing inaccuracies, as well as...

In an equally perfect manner & style – designed in precision gold bands that each match ring holds a place in hearts all same & shining same in grand elegance - precision craftsmanship brings out brilliance so when our fingers intertwined as they...

The receiver coil should be over the non-perforated region of the base. WIRELESS POWER:The major change here is that I added an wireless receiver module to the bottom of the assembly coupled with a wireless transmitter module for installation under...

The Y-Splitter snaps nicely in place on the back cover of the printer.Remove the stock coupling. </strong><i>I wanted to reduce the weight and length of the whole setup. Since this model has pneumatic connectors on all 3 entries, the stock one isn't...

=========================================================== __Update: May 9, 2021__ A quick update on our progress and a couple more pictures. You can see the two Dyna-Soar nose cones next to each other. As the original nose on the left needed to be...

They aren't really required - they just provide some more protection. In addition to the printed parts, you will need the following: 1) 1/4-20 threaded rod, 3" length 2) 2 1/4-20 nuts 3) 2 M6-1.0 hex bolts 16mm length 4) 2 M6-1.0 hex bolts 30mm...

For buttons you will need a latching style so it stays press when turned on such as this one: https://www.amazon.com/gp/product/B075VBV4QH Optionally, a couple of supplies may come in handy to handle leans. Zip ties will work as added insurance for...

ONE SIZE FITS ALL FOR THE INTENDED PURPOSES OF THIS PRINT IT'S ESSENTIAL TO SIZE THEM CORRECTLY FOR ---YOU---Note: 2 Options for a .stl and .3mf are listed one in a smaller size one in a larger for those of you who are too lazy to scale the print up...

There're a couple things you can configure before flashing your Arduino: rf24_rx[5] - Is a 5-character channel that is the unique id for each puck, for individual addressing. Give each puck a unique number but leave the first three characters...

I tried to stick with 60 words as much as possible, but a couple of times, it got a bit over. Please let me know if that's an issue. Thanks! 😊</s> P.S.2 I also tried to maintain the same tone and enthusiasm level as in your original text. Let me...

Once it is assembled, test it by giving the reel a couple turns in both directions and make sure it all works. I found that the rubber band smooths out after several cycles. Printing tips:</p> <p>BASE: I printed the base with supports but used an...

&nbsp;Tolerances are pretty close with the model so if your spindle gets stuck, enlarge in PrusaSlicer by a couple percentage points. &nbsp;</p><p>This model has been tested on the Prusa i3 MK3S+ and Mini+ with a 0.40mm nozzle at 0.15mm and 0.20mm...

Hand sketch the outline of the ship on paper from the side - I'm considering doing a front/back view for a couple ships for added stability. 3. Scan/Document Camera the sketch to get a jpeg 4. Open the jpeg with Gimp/Photoshop 5. Use...

The list of parts you will need is as follows:An Arduino-based microcontroller (Arduino Pro Micro in my case)A real-time clock module (DS3231 or similar)A TowerPro MG995 continuous rotation servo motorA standard LEDA standard light-dependent resistor...

I do not have the ambition to set height records etc.After looking around on Thingiverse and in the internet, I found designs based on the Gardena garden hose coupler.My design is based on this Gardena coupling and on a 0.5 or 1.5 litre PET mineral...

It took nearly 3 weeks and a couple dozen fundamentally different designs before settling on the current GateRodders design for SC17. A NOR gate is fundamentally a NOT gate imposed on the output of an OR. The input and output rods are trapped...

By continuing smoothing for a couple more times, the remaining layer line artifacts should completely vanish. A bit of over-extrusion might help, too.</p><p>If you look from the other side, you can perhaps guess that the smoothed PVB acts as some...

Couple Bands: Elegant duo bands, available in diverse metals and adorned with stones to symbolize unity. Casual Bands: Stylish and minimalist design for everyday wear. Suitable for modern and sleek appearances. Cocktail Bands: Edgy yet...

&nbsp;Make sure the number on the Jaw Gear matches the one on top of the Align Tool.&nbsp;LUBRICATE:&nbsp; If you want your vise to really move smoothly, &nbsp;add a couple of drops of oil to the Jaw Gears Teeth before installing the scroll plate. I...

&nbsp;I created a couple of simple ‘end stop’, these are also 3D printed.Using a common technique with a nut and bolt. You can hand tighten the end stops in place, therefore no tools are required and the swatches are held firmly in place whether you...