statue thinking 3d models

I had it moving quite slow (think it was like 10mm/s) and would repeat the test 3 times and assuming they were very close make an adjustment to the steps. The remeasure and repeat multiple time till it would give me repeatable movements within 5...

I think with a taller sprue I could have a little more pressure on the very top of the coin and get the edge to fill out a little better. I'd also like to add a little lip to make releasing the mold easier. ...I'll update when I get a bigger printer (on...

https://www.amazon.co.uk/gp/product/B0755WT39B/ref=ppx_yo_dt_b_asin_title_o00_s00?ie=UTF8&psc=1 -Glare and distortion on faceshields and other windowed masks make it too difficult for some lip readers I think. Seems it is a very exact talent that...

I think if I was to print another I'd like to try is to print the first two layers in white, then pause the print and switch to clear to get the maximum balance of light-diffusion from the front, hiding the back of the LED strips and light coming out...

I think it goes through some sort of calibration when it starts up after power is disconnected. Note: The perimeter around the dimmer needs to be covered with something like black tape or black paper. If you don't, you will get some light bleeding...

Wheels:I think is especially important the material composition of the tires is as similar as posible to real ones, or better said, with the most "grip" possible. So, instead of trying to imitate the shape of the tires and print them in TPU to see...

X-axis twist causing failed bed levelling, while not specific to lulzbot, is heavily mentioned in the reprap forms when people think the bed levelling code is buggy when it is not. Anyways, I designed a custom frame stabilizer which mounts across the...

Dimensions (L x W x H): 94mm x 54mm x 178mm (the height of 178mm can be changed by adjusting tube and shaft lengths) Whilst this has no official scale, not having a full size prototype, I think it would work well with 1:6 scale figures and boats. ...

Improvements that I think could be made: Black Ram Assembly The joint between the gauntlet and the wrist assembly could use a conversion to a ball bearing. That joint counters the pressure applied to the apparatus at the end. While testing the...

As I am using a 4A 5V DC power supply, and the switch I am using is rated for "AC 250V/6A 125V/10A" I think it should work OK, but again I am not an expert on this, so make your own analysis regarding the switch. I based the choice of switch I am...

Please think this project through before starting. I've been focusing on this for weeks and do not have comprehensive instructions.</p> <p>Update planned: I'm planning to drill a hole in the Replay binnacle after my 12V connector hardware arrives on...

I wouldn't go thinner than 2.65mm, I think, nor would I go much over 2.75mm. The mould was designed with a 3mm "gap" between top and bottom to accommodate the veneers for pressing, so 3mm is probably the maximum thickness one would want to try (plus,...

Individual panels are easy to customize and swap out.The system I came up with consists of 112mm-long knife panels that are sized in increments of 12mm wide; think of this as one unit (1u). The main panels are 2u (24mm wide), and oversized panels 3u...

Just thinking: setting number of wall lines high may prevent the pattern on the sides/fronts and needs less sanding. --- ###Building For 901-211, 901-213 and 901-214 cut the waste pipe at the bottom, there is no toilet. Hints for upper...

Insert the grub into the FL_OverOut hole near where the light attaches, do not screw past the inner right for now.&nbsp;Initial Light Prep:This is optional but for me necessary cause I'm a perfectionist and cant sleep at night thinking about these...

Thinking about it more, it is because I generated the array with a 12 inch focal point and then uniformly scaled the array up to 150% of its original size to fit 1 inch hexagonal mirrors. Since the angles of the mirrors didn't change after scaling...

leave the lower mount bolts loose (10mm m5 bolts and T-nuts with washers I think) Repeat with the right hand side pieces and other crossbar. Use the alternate upper end for the left side if you are running cable chain. </li> <li>Now bolt the arms to...

They all felt she said exactly what they were thinking, as if her words had power over their thoughts. One of the townsfolk questioned “What about Lord Tenebrae? What if he finds ou-” “The vampires will never find him if you bring him to the...

Think of it as a uniform thickness of the “l” character. If you were switching between fonts this keeps a uniform lineweight. Size isn't correct for some programs (like blender) that don't seem to use baseline height correctly. This lookup table may...

You can swap lower arms between sides depending on what you think looks better. Re-attach to shoulder sockets</p> <p>-- Flip the head and insert it back into its grooves so that it is visible. Attach the "backpack:" behind the head.</p> <p>-- Align...

I recommend turning off the supports because it's extremely complicated to remove them.&nbsp;You have to print two of these parts.uicm-motor_gear&nbsp;is the simplest part to print and I think everyone can make this right. I only recommend using 15%...

I think there may be enough room between the mount post and edge of the case, but I have not tried. I used this switch: https://www.amazon.com/QOFOWIN-Rocker-Toggle-Switch-Marine/dp/B07S8TJ9NG and this LM module: ...

The whole game concept is about quick thinking and reactions.Place all five items on the desk, so every player can reach them easily. All the playing cards should be facing downwards.&nbsp;</p><p>Quickly turn one card, so everybody can see whats in...

I think one without the button fuction would have a better feel. ...Building the remote is not as difficult as building the robot but it still involves soldering and programming the chip.</p> <p>Good luck,<br/> Rick</p> <h3> Print Settings</h3>...

...Based on many designs floating around Thingiverse. -Cool - Looking Tool Head Besides looking totally cool ( at least I think so), the extruder assembly is very functional. It houses an E3D Lite6 hotend, and is capable of printing flexible filaments.

It should work without add on but I think it works better with it, you just have to glue it into place. Also some clearance issues were fixed but not all.</h5><p>&nbsp;</p><h4>How to print it:</h4><p>Some parts are designed to be printed without...

When thinking about how to improve the acoustics of a Peli Case, the compact Bose Wave backhorn speakers came into my mind. Driven by that I stumbled across this nice backhorn speaker design by guppyk: https://www.thingiverse.com/thing:4668173 which...

There are many like it on thingiverse but I think this is the best design. <a href="https://www.thingiverse.com/thing:3182594">https://www.thingiverse.com/thing:3182594</a><br/> Note: Prusa has a new 60 Degree angle adapter that may or may not be...

I think a good PLA or a normal PLA+ is absolutely sufficient. for the BB loading rings TPU. It will even help to avoid damage caused by throwing. The assembly is particularly easy, so that if assembled correctly, the grenade can be disassembled and...

with that I think it's also possible to shave up 1.5-2mm which should bring it in range of what's needed. If someone wants to make these necessary changes I'll be happy to explain the OpenScad code if needed to get you started. **End Warning** ...