tape scraper 3d models

I used velcro tape (soft/loop side) to protect the sword from scratches. Warning: Tell your friends several times that this is not a real sword for swinging around violently. (Even if they secretly have ninja training or something.) The internal...

Ensure all components are insulated, I used heat shrink and kapton tape. Check for overheating and good air circulation. The code for the Wemos D1 Mini is in the AlarmClock.ino file, just copy and past it into the Arduino IDE to compile, use the...

How I Designed This Design Process My first version was made in cardboard and tape. Although it was crude, I was able to rough out the positions of the devices. Then I used Autodesk Fusion 360 to design multiple iterations. Each time I printed the...

One holder fit the vive a little too loose so I stuck a few small shims of masking tape to the inside edge (of the lens holder). Wanted the fit loose to make insertion/removal easy but tight enough so doesn't fall out during regular use. To assemble...

The base I did at a PLA fast print profile .3mm layer and 10% infill. 0mm - Gizmo Dorks - Orange (yellow) 1mm - Flashforge - Orange 2mm - Ziro - Matte Chocolate Base - TTYT3D - Rainbow Multicolor (bronze section) Post-Printing Easy Assembly Print 4...

Materials Needed: * 1 x 3D printer (any type or size) * 1 x 3D printing filament (PLA or ABS) * 1 x Rope making die (you can design and print your own or purchase a pre-made one) * 1 x Measuring tape * 1 x Pencil Step 1: Design Your Rope Making Die...

Place it all in the 3D printed enclosure and glue it together (all pictures display electrical tape as a temporary adhesive). FOR MORE VISUALS, I POSTED MOST OF THE PROCESS ON MY INSTAGRAM @ stovie_steam. https://www.instagram.com/stovie_steam/ ...

If you find the Key-Bak can still move inside the enclosure when it is completely closed, put some foam tape in there with it to keep it from rattling. Once installed, the enclosure should clear the lower rear belt by ~3 mm. If you have problems with...

I used some Parrot vinyl tape (red 3mm) to mark the red stripes - ideally you would need 2mm, but I could not source it where I live. Turned out well though. Added the nose spike, using some PLA that was heated and starched to achieve the right...

The setback of the sanding block face is designed for one layer of Xfasten Double-Sided Carpet Tape and a 4.5" x 1" piece of 3M Cubitron II sandpaper. I'm sure most adhesive backed sandpapers will be fine. If the sandpaper is a bit proud of the...

If using 1.75dia filament, you can print with it or use painters tape on the outside edge to keep the treads together. The bases were updated on 01/23/17 to correct clip size and added BASE FROUND and DOWN FROUND which is a 3" halfround married to...

Advantage: -No cover drilling or printer modification needed -Simple straight forward design, upgrade possible -Small footprint, stackable -No more smell and fines particles Part needed: -1Kg of PLA -2mm HIPS sheet for the upper and lower cover...

If you haven't laminated the model, it should work great to use some tape around where you want to cut the nose temporarily just to get support and guide for the hacksaw blade. Rotate the models 90 degrees and click on lay flat, just like in the...

The bill of materials: 2.5 rolls of 1 kilo PLA 24 battery-operated candles 24 cans (do not buy 24 cans of V or red bull and drink them to make this, that's too much and can make you end up in hospital, look for empty ones) One can of paint A bit of...

A wrap of electrical tape around the bearings or some rubber type glue is a workaround if you want to use the part. I turned up the flow a bit and they work perfectly. I still drilled the pivot pin hole (you can't fix it if it prints too loose,...

If necessary, you can use tape if it's too loose. Adjust the height of the duct using the two screws of the fan. Do your cable management (you can use zip ties). Modify the offset in the firmware. If you're using Marlin, here are my parameters;...

This design uses WS2801 NON-INSULATED Diffused Pixels that have been separated, wrapped in Kapton tape, bent and push-fit into the diffuser before being reconnected with bare copper connections. This is the type of LED I used because it's what I had...

I used orange smartbuy PLA filament and did not employ a heated bed; instead, I relied on painters tape. I discovered that I needed to lower the print into the bed by 1.75mm so it would sit upright straight away. You will see in the test print that...

Protect the Leaf's bodywork with some sticky tape before printing to avoid scratching it. 4. Once the print is finished, remove all support materials using pliers or a knife. Insert the camera's cable through the hole at the back of the mount and...

If the name plate is loose, double sided tape will hold it nicely Others I did not test the "Stratos Only" base back wall and name plate but it should works fine. Feel free to send me any feedback on how to improve the design. Suggestion on display...

Depends on the shape. All parts are printed 100% solid. Parts are printed standing up. Can be printed with 0.3 layer height. Can probably be printed with resin. If you have a slippery phone, you can add some foam tape (like weatherstripping) to get...

I discovered that applying Kapton tape to the tube greatly improves the gland nut's performance. I am still experimenting with other tube holder methods. The small filament driver, measuring 11mm in diameter, is mounted on an M8x50mm bolt that I had...

* I use a PTFE tube up to the spooler and put all the cables around the PTFE tube and fix them with tape. **Step 6: Configure FABUI** * Insert the NEMA steps as per E3D instructions in the extruder calibration in either settings or maintenance (I...

I used ESD tape to secure the battery and the speaker to the holocron base (I chose not to make housings for these components within the base, since different components could be used here). That's it! ...Please post any pictures of makes, I would...

The name plate will need some double sided tape to hold it nicely. Others ==================== I did not test the other base variant but it should works fine. Feel free to send me any feedback on how to improve the design. Suggestion on...

To protect the glass of the tank from damage caused by the adhesive used during assembly, please apply a layer of adhesive or masking tape over the glued areas. After the adhesive has dried, remove any joined parts. If they are too tight to remove,...

and post some makes if you use these it lets me know I'm not wasting my time uploading my designs and if you like what you see check out more of my lures at https://www.theneverendingprojectslist.com/ The Printing Process. The process starts by...

I originally intended to use double sided tape to hold the tray to the sides of the frame, but the final design uses six 12x3mm magnets per side, and one of the set screws to hold it at one end (this is where the slot is located in the model). The...

Put some double sided tape on the door handle. 1. Stick the model to the door handle like you'd want it to be when attached to the wall. 1. Apply glue to the back of the printed component. I used hot gun glue because it was within reach. 1. Open...

If you are pulling the filament towards the side of a table simply add some adhesive rubber on the edge, as visible here on the top-right: Using a very small piece of double-sided tape on a single support (so that the other is free to slide) is also...