ts100 tip 3d models

Rumour has it that Naboo N-1 Starfighters are so easy to fly and fire, even a kid can do it!The needle-tipped N-1 model by our contributing 3D artist perfectly embodies the elegancy of one of the fastest starfighters of its time. The author of the...

&nbsp;Connect with other amateur astronomers, get advice, do observing challenges and more!Message #resources&nbsp;How can I support this?Tips are always appreciated, as is support on Printables. &nbsp;I'm also (barely) on <a...

Just a few tips on settings. The Dragon hotend does not need as much retraction as stock Qidi. I find around 0.8-1.0 mm is good with a retraction speed of 25 mm/s, depending on filament. If you get blobs on layer changes, disable "travel prime" in...

Four laser cannons that are known to be found on the TIE Interceptor only are mounted on the tips of the 3D printing model’s arrow-shaped wings as well. A deadly and speedy addition to your 3D printed Empire's military might is ready to reinforce...

Victor's design has several sizes of printable tips that are the equivalent of the ceramic nozzle in the HF gun, and I don't think they'll last very long with dry media. What I did was create an adapter that will hold the ceramic nozzle in the...

Tip: A small sponge roller with some thick primer once you are happy with the shape is a good way to replicate the texture of the computer's plastics. ii) Just send it off for commercial printing! -Many of the problems become someone else's but...

#As seen on [HACKADAY.com](https://hackaday.com/2020/04/30/an-all-lead-screw-3d-printer-you-can-build-yourself/) [You can find us on Discord!](https://discord.gg/R2vPAdQPEQ) For tips, help and 3DLS specific stuff! [Here's a 4k render of the...

As it is now, with a ½" screw, the tip of the screw is just starting to engage the hole for the screw shaft when the head of the screw is starting to disappear into the larger hexagon hole. With a properly cleaned-up print, I didn't really have any...

Please be careful.After breaking the hinges and removing the tape, you are done!&nbsp;TipsMake sure there are no wrinkles in the tape.If you are printing a large version with really sticky tape, you can use sticky-side up tape underneath the...

have a look at the included photos[ ] Tips: Because the wires for the heat plate are very short use an unused female socket extension cable to add some extra length. Use this to pull the wires through the access port opening in the control board...

Share about two drops between all of the roller bearings, just touch the inside of each bearing with an oily tip and add another drop to the gear teeth; that one drop will quickly spread around the entire gear train.&nbsp;&nbsp; &nbsp; &nbsp; &nbsp;...

TIPS FOR OPTIMAL USE - Breathe in through your mouth ○ And out through your nose…… You'll release far less vapor that way between talking § Reduces the frequency of sponge replacement and washing up liquid re coating. - Carry spare washing up...

If this is not the case, check - the position of the jaws with respect to the effector - the tension of the suspensions - the tipping point of each micro-switch ###Configuration Marlin Firmware 2.0.xThis configuration is that of my machine which is...

The eye join doesn't technically need much for support at 0.1 layers, but fiddling with tower/tree settings to get some bonus material around it will make it more likely to print successfully without getting knocked over or warping a lot....

The filling material will otherwise stick to the walls of the glass and it also might clog.Pro-tip for smoothing chemicals (absolutely optional)You can mix a bit of antistatic spray with IPA to make an even better chemical for smoothing: So the...

I used a cotton facial pad and some Kapton tape for mine and it's doing fine. 6x M3x12 bolts for the barbells 6x 10mm x 1mm washers for the barbells 8x M3 nuts (2 for the hot end lock, 6 for the barbells) 2x M3x16 bolts for the hot end lock (you...

And the greenhouse is ready, which you can easily assemble and disassemble.&nbsp;If you have any questions about the instructions or would like more tips, don't hesitate to contact me.&nbsp;Important:Whenever you work with wood, please remember that...

The rest should be self-explanatory.A tip: Before you set layer heights, set the maximum layer height limit in the printer settings/extruder settings to the value you want to use for the thicker layers (0.2 mm in the example file).&nbsp;In Simplify3D...

This is a little Diesel Generator model I tipped up this morning to act as cargo (terrain) on my SCI FY layout.&nbsp;There is a new more detailed version (see photos), but both models are still available. The new model has no stringing (fixed) and a...

This can be applied with a thin, fine brush, or a sharp, pointed awl, or even the tip of an Exacto blade to simulate rust streaks where water would naturally run and pool over the model, such as screw slots, rims, joints and junctions, etc.Once you...

Enjoy!Just a few tips on settings. The Dragon hotend does not need as much retraction as stock Qidi. I find around 0.8-1.0 mm is good with a retraction speed of 25 mm/s, depending on filament. If you get blobs on layer changes, disable "travel prime"...

Enjoy!Just a few tips on settings. The Dragon hotend does not need as much retraction as stock Qidi. I find around 0.8-1.0 mm is good with a retraction speed of 25 mm/s, depending on filament. If you get blobs on layer changes, disable "travel prime"...

Just a few tips on settings. The Dragon hotend does not need as much retraction as stock Qidi. I find around 0.8-1.0 mm is good with a retraction speed of 25 mm/s, depending on filament. If you get blobs on layer changes, disable "travel prime" in...

This house is at the tip-top peak of Truckenmiller Hill (formerly Portuguese Hill) which has got to be one of the biggest, relatively undeveloped chunks of land right smack in the middle of the city of Sonora. It's remained undeveloped probably...

Carefully tipping the rocket body to allow the superglue to dry and smooth out.Repeat this process until all 3 fins are in place.&nbsp;&nbsp;Producing the launch guide&nbsp;When launching a model rocket from a standard launch platform a 3.5mm guide...

This ensures that the joysticks will be correctly oriented afterwards.&nbsp;Then simply select the joystick or tool you like from the following list and connect it to start playing!&nbsp;List of available tools (updated on 01/01/2022):Single...

* This took quite a few hours to design and test, so if you feel like it, please leave me a tip so I’ll be motivated to design and post more things. * Disclaimer: I am not responsible for any injury or broken items. Build and use this rack at your...

This giant whale shark fish-man knows firsthand about a true soldier’s honour, the value of friendship and humanity, excellent battle strategies and other useful tips that will come in handy on your quest. That is why our contributing 3D artist...

In order to receive the cleanest result possible the monster’s jaws were extracted and are now provided as separate parts, as well as the model's two-tipped whip-like tail or each side of the alien’s extended skull. All assembly parts are provided in...

So if you have any tips or comments feel free to leave a note. The included files are not ment to be used yet. I just added them for documentation purposes and they will update frequently. When I finished my design I will include the FreeCAD source...