vertical plotter 3d models

Check out these vertical rod supports. http://www.thingiverse.com/thing:35013 I think they are better and look better than the wood ones used. You don't have to disassemble the extruders electronics to take it apart. Take out the Y-axis rods and...

On the second run the calipers should now display more or less exactly 50mm. I added several holes at the base, so you can mount the tool onto a 2020 beam for vertical use and calibrating the z axis steps. You can also mount the tool onto the print...

To help reduce stringing, print the top and bottom pieces separately in a vertical orientation.In order to give this some heft (and because my print bed would not fit the entire wand in a single piece) the split model has a stiffener slot for for a...

Ideally the part should be installed so the inner flat faces are to the sides, which will put the layers in a vertical plane oriented along the part for maximum strength vs. gravity. There should be plenty of clearance, though you might need to shave...

The pins position it vertically. No measuring it is required and the holes match up. This design was inspired by Tamar at https://www.3x3custom.com/tutorials/adjustable-dowel-jig Mine has a few more features, but it will still be helpful to see her...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8...

This is a remix of the Prusa Mini Z-Top | Electronics Box Lid by freewheeler, the Raspberry Pi Zero mount lid by Deeps, and the Pi Zero hex lid by crokobacon with the following changes:Boxier design that, in my opinion, visually works better with the...

Be careful of the angle, it should be vertical --MAIN BODY: Main Body (01) and Top Half (02), and Chest Gem (23). Easy. Glue the top half onto the main body, and the gem onto the recessed square on the top half. Be mindful of the spacing around each...

Available variables include * the stack count - one can chain (vertically) the pump. One (1) is all I have used. * the cog shape profile, * the number of outer ring teeth, * the number of sun teeth, (the ratio between ring and sun teeth will...

I have given extra tolerance around vertical layers above the magnets to compensate for a lower roof where the magnets would go. it works great during my testing. This was designed with a printer that was calibrated using Cura's Horizontal Expansion...

See also http://youtu.be/7F2fIF9PNBk for a short demo video of the original version. To store a coin, you may release a coin from the rightmost top, and it will slide down the hill and go into the appropriate tube. Once a tube is full, remove the...

There are horizontal, vertical and picatinny grips available. Parts tagged with 16mm are for 16 mm OD or Caliburn-spec sized barrels. - Triggers is for picking the right trigger weight for your blaster. Heavier ones need more force to pull but are...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

I recommend you start with the Maybe-No model first. Move the shaft 60 deg so the two grooves are front visible:  Insert the Maybe-No print and align face connecting the No and Maybe side horizontally to the open face of the...

Be careful of the angle, it should be vertical --MAIN BODY: Main Body (01) and Top Half (02), and Chest Gem (23). Easy. Glue the top half onto the main body, and the gem onto the recessed square on the top half. Be mindful of the spacing around each...

&nbsp;If you print the track vertically you will likely want the .16(x2) tolerance track. &nbsp;The slicer tends to curve some of the features that are more defined with layers. &nbsp;</p><p><strong>Hardware</strong></p><p>5mm, #8 or #10. &nbsp;For...

These units feature remote control operation that allows users to rotated the light 370 degrees with a hard stop and to adjust vertical tilt through 140 degrees. Remote operation is provided by one handheld wireless remote controller that operates...

A bed that is not square with the frame prints parallelograms in the Z-axis vertical plane, not rectangles with 90 degree corners. For that reason, I have created a probe extension and coupler that allows you to perfectly square your bed with your...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

Figured out I could use vertical steel pins and it works awesome.  Ergonomics gah so much work went into these. This was the real treat to designing this. Got them exactly how I wanted and a good understanding of what makes a comfy grip moving...

Hightower: A 3D-Printable Vertical Mini-ITX PC Chassis This is a Mini-ITX case in the style of the Xbox Series One, the Phanteks Evolv Shift, or the NZXT H1: it has a small footprint, but plenty of space inside. This is designed to be printable on a...

The upper hardware goes into the 2020 gantry (side to side) and the lower hardware goes into the 2040 vertical extrusion.Note that the holes are slightly oval, to allow adjustment and alignment before tightening. Lower Z Brace AssemblyThis piece is...

Now you can mount whatever you want and you can change the vertical position in a blink of an eye.&nbsp;InstructionsPrint with supports (Important! Take a look at .gcode</strong>). I recommend using the “Intelligent mode” of prusa...

Adjust the worm so that the rudder is pointing straight ahead and is also vertical. Pull both sides of the string taught and tighten with the clamping screw. This will take a bit of fussing and you'll want to study the video.</li> <li>Assemble the...

In reality the handrails are all in the same plane, but that would make it an absolute pig to solder, so the jigs are set up to solder the second horizontal bar behind the vertical bars. To be honest, I have no idea how well a printed jig will work,...

At full power the glider climbs almost vertically. Some attention should be paid to the coloring on the underside of the wing. As a pure thermal glider, visibility of the model at higher altitudes becomes important so as not to lose sight of it. The...

&nbsp;Print 2 x 70mm and 1 x 31 mm.Aligned vertically on the plate they will take ages but it'll save you having to source tubing or rods of 6.23 mm diameter.***********************************************************4 x rubber bands about 32 mm...

Shimano style clamp band My style of clamp band Parameters BarDiameter = 23.8 mm: modern handlebars fit this standard HorOffset = 33.5 mm: horizontal offset VertOffset = 15 mm: vertical offset The offsets are used to set the position of the base of...

This is a redesign of the MMU2S Print buffer system to relocate the 5 spools above the printer and a rear mounted vertical buffer system. It saves a lot of space, fitting within a 56cm X 56cm (22" X 22") footprint. It just fits inside an IKEA Lack...

Two offset LED assemblies within the fixture allow this explosion proof linear lamp to provide a brilliant 100° horizontal beam spread and 140° vertical beam spread while achieving a 10,800 lumen output to maintain a small form factor. The LED...