wasd keycaps 3d models

Required Hardware/Software: * 1x Teensy2.0 * 4x M3 5x5mm Threaded Inserts * 4x M3x8mm Screws * 25x Cherry MX Switches (or other 14x14mm sized switches) * 25x Compatible Keycaps * 1x Micro USB Cable * Ribbon Cable * Basic Soldering Equipment...

I used: 24 Kailh choc switches and keycaps 24 diodes Third party joycon analog stick replacement. A first-party one ought to work as well. 8x screws with threads suitable for plastic, roughly 1.6 - 2mm by about 6mm long, to hold the controller...

No keycaps are included in these files yet. Check tolerances or model your own before printing this. If you'd like changes or have any suggestions, let me know. STEP files are also included for people to modify.<br>&nbsp;</p><p>Hardware:</p><h5>16x...

The keyboard body consists of a polygonal mesh while the keycaps have been subdivided, giving it added detail. Base polygon count: 15,684 When Subdiv Level 2 is applied, the polygon count rises to 128,340, showcasing exceptional precision in its...

Keycaps, i used DSA profile to keep the keyboard feeling small, lowercase legends help extend that feeling My Other Stuff: https://cults3d.com/en/users/revere521/creations https://www.printables.com/social/406094-revere521/models...

diameter, 5mm height)M3 brass inserts x16M3x6mm socket head screws x16M3x14mm socket head screws x6 (if the tent kit is used, will replace x6 M3x6mm screws)&nbsp;Print SettingsRafts: NoSupports: NoResolution: 0.2mmInfill: 20%Filament: Anything you...

See below.Parts List:Print x1 "Upper"Print x1 “Lower” (choose either combinable or not)Print x18 “Keycap” (different colors are nice!)Print x1 “Large Keycap”x1 Arduino Pro Micro (I just get a cheap off-brand, they work fine)x19 Cherry MX Keyswitches...

I paced 8 across the front edge, 3 on each side, and 4 across the back.&nbsp;Key Map:The Key Map is essentially the same as TheAlternate and match the keycaps in the photos - these are the function keys:Fn+Q = resets the keyboard (no bootloader)Fn+R...

The recess in the bottom of the case should fit a teensy 2.0 (i had one floating around) My intention will be to hand-wire this prototype and modify the QMK firmware used for imchipwood's dumbpad (https://github.com/imchipwood/dumbpad) Later, i will...

It uses four Cherry MX-style key switches that I had left from a project, printable keycaps are included but these take a good printer to work well. If you can't print them most standard keycaps should work if you buy standard switches. You can...

**Parts List:** Print x1 "Upper" Print x1 “Lower” (choose either usable by phone, computer, or both) Print x18 “Keycap” (different colors are nice!) Print x1 “Large Keycap” x1 [Arduino Pro...

I paced 8 across the front edge, 3 on each side, and 4 across the back.Key MapThe Key Map is essentially the same as TheAlternate and match the keycaps in the photos - these are the function keys:Fn+Q = resets the keyboard (no bootloader)Fn+R =...

See below.Parts List:Print x1 "Upper"Print x1 “Lower” (choose either usable by phone, computer, or both)Print x18 “Keycap” (different colors are nice!)Print x1 “Large Keycap”x1 Arduino Pro Micro (I just get a cheap off-brand, they work fine)x19...

Updates to the original Palice Keyboard include: + Plates for Plate Mounted Stabilizers + New Anchor points for plates (previous ones were too flimsy) + Fixing holes to better accommodate the M3 threaded inserts in the covers + General fixes to the...

It's not perfect (yet :P), but already thought somebody might like it so here it is :)Keyboard case consists of:FrameMain keyboard part (walls, bottom and holding mechanisms)&nbsp;Arduino Micro holderPart for holding Arduino Micro (it's separately...

The plate and PCB fit, but a few of the keycaps in the upper-left and lower-right rub against the case. Therefore, depending on your printer setup, you may need to print these cases at slightly larger than 100%. The ledge mount, however, works as...

This version was specifically made for a GMK keycap so I think cherry/OEM would also work OK. I will get the version for XDA/DSA etc up in couple weeks hopefully.</p> <p>The code for this version and the original version can be found here: <a...

Keycaps Assembly: 1. Print the top and bottom halves along with the small cable cover if you want. 2. Trim and file the edges to clean the print - especially the mating faces 3. Pin the halves together to form a full top and bottom. The halves are...

This build used Cherry MX Browns, with purple (caps/scroll lock) and white in-switch LEDs, and purple and white keycaps from Signature Plastics. The purple-and-white theme was an attempt to evoke the purple trim on Sun hardware. ...On a Sun keyboard...

**Tip's & FYI:** • Button-Switch and KeyCaps - I used 12mm Btn-Switches but, you can reposition the Pads (in Gerber) to accommodate 6mm Btn-Switches • Wiring - my approach was preliminary and quick and I didn't care about it, I just wanted to get...

* 1x Adruino Pro Micro * 12x Cherry MX Switches * 12x Cherry MX Keycaps. (You can print up your own of course. Not included here) * 4x M3x16 mm Socket Head bolts. * A piece of double sided 3M wall tape. (the thick kind you use to hang...

Electroblocks give you the power!You Will Need (Affiliate Links Included):5V Arduino Pro Micro - http://amzn.to/2tqNsJUCherry MX Black switches (8x) - https://amzn.to/3p5QX3E https://s.click.aliexpress.com/e/_9i602bKeycaps (8x) -...

There is an LED backplate below the keycaps to simulate realistic light spill between the keys more accurately. ONLY FOR OCTANE: Two different versions of the Apple logo on the Screen Panel are included, as seen in the various renders. One is the...

Here's what you'll require: Teensy 2.0 - $11 (or purchase a knock-off for ~$6) Mini USB cable - $5 Rubber feet - $4-6 (or print them if you have TPU) Hardware - $4 Standard "OEM" Keycaps - $8-10 (for single color) 70 - Cherry MX style switches - $10...

Use keycaps of your choice. I recommend 1.75u for the main buttons and 1u for the extra buttons. You may find models to print here on Thingiverse. like this: https://www.thingiverse.com/thing:4920619 The bottom of the Turntable disc need to be...

Also switches did not lock into position well and would often pull up when exchanging keycaps. In addition, although the macropad is designed for either 18 switches or 20 switches the plate is really only designed as hot-swappable for the 18 switch...

Keycap set (as well as spacebar stabilizers). Wire (a mix of 22 gauge and 28 gauge worked well for me). USB cable. Kapton/other insulating tape. Soldering tools. Tips: Maybe carve a small piece of the plate into a quick test print to check Cherry...

You will need to remove certain of the keycaps to expose the screws. (d) Once the screws are removed, lift the plate/pcb by a few inches--only enough to access the cable, which is still stuck to the bottom of the case. At this point, you should...

In order to mount everything properly, you will need:Philips screwdriver, 5mm socket and driverMetric motherboard standoffs (M3, 6mm female, 6mm male)M3.5x10mm screws for the PSU.Standard M3.5 chassis screws for the GPU (M3.5x6mm)If you print the ATX...

The plate and PCB fit, but a few keycaps in the upper-left and lower-right rub against the case. Therefore, depending on your printer setup, you may need to print these cases at slightly larger than 100%. The ledge mount works as intended. 1 (Ledge...