who designed ssj4 3d models

This is a completely new version of my original design (here: https://www.printables.com/model/145632-dslr-rig) without the cage and with fewer parts. Redesigned in SOLIDWORKS for higher precision.You will also need:15 mm aluminum or carbon rods...

Two initial designs were done several years ago, one created the pulse width signal using hardware and the this one (what I think is more sustainable) uses a cheap Arduino microcontroller to do the job. A transistor is used to do the heavy lifting,...

The front support must be flush with the front end of the base. WRIST REST ASSEMBLYSlot the two rest support pieces into the narrow, elongated holes in the base (left or right side) and press on the rest with the curved edge to the inside.You...

There it is inserted into the corresponding insert.AssemblyThe model is optimized for 3D printing and consists of three parts:Front panel with solid mounting struts (black) for the actual caseCase bottom (orange), is inserted into the strutsCase...

I'm designing some other similar toys that will use the same system. I'll share them when they are finished.</p> <p>There are two versions of the mcu board. One uses an Attiny85 and the other uses a Picaxe 08M2. I used to do a lot with the Picaxe and...

based on my mirror array experimentation here: https://www.thingiverse.com/thing:5158449 and https://www.thingiverse.com/thing:5162096 All of which is very much derived from the excellent design here:...

An effector and fan shroud mount for the E3D Hemera for delta printers. This direct drive effector works quite well with well designed delta printers like the Ultibots D300VS or the various SeeMeCNC printers that use the SeeMeCNC machined aluminum...

Mirko - automata butterfly toy is made to fulfil all necessary requirements defined by Printables for Technical Marvels competition.&nbsp;It is made out of several parts that can be glued or secured by screws, there are moving parts (I chose to use...

-FOLLOW ME ON INSTAGRAM and FACEBOOK Fanpage- https://instagram.com/3dprintmodelstoress https://www.facebook.com/3dprintmodelstore [3dprintart.design@gmail.com] 3DPrintModelStoreSS Sukuna Cursed Technique Tool - Jujutsu Kaisen Cosplay Weapon 👁 1.8k...

SUMMARYI designed this Bluetooth speaker in the Fall of 2020. I am NOT an audio engineer, nor did I have much knowledge about what I was doing from an acoustics point of view. But it still turned out great and sounds amazing. There is no build guide,...

- - - As you can see, I have rationalised the original design, basically making the parts more compact and lighter (less plastic & shorter screws), keeping their rigidity. So the prints on the pictures do not correspond 1:1 to the STLs you will...

All LEDs are 5mm types and are attached with LED sockets The two outer sockets (black and blue) were a special design that I still had in the craft box. Since I am assuming you don't have the same sockets, I modified the front panel so that all the...

Another change is the use of LEDs instead of incandescent lamps, and of course the microprocessor control implemented by arduin with the mcu AT Tiny85. The front and rear lights are identical in design and differ only in the shape of the body itself...

I used this 5/8" tall flat bellows available from McMaster Carr:https://www.mcmaster.com/1320K111/These bellows are made for this job and are resistant to oils, lubricants, and heat.The models are designed to fit an Eerie Tools SM-LTHM 7x14 lathe but...

I'll have to redo a couple of them, but most of the design work is already done, so it shouldn't take long. They're coming, though! UPDATE 7/30/2021: New versions mentioned in previous update should be up within the next week or so. Doing some...

These work a bit easier, you have to use some glue on the end of the arms where they engage each other but they do form a more substantial frame to hold everything in place. The design is such that all the electronics is upwind so the ozone, which is...

Downloaded some Radio Control model yacht designs. Non of them suited my fancy for building, so I decided to come up with my own. Main Desing principles... No Keel! -> Surf Board / Windsurfer style. Light Weight (relative to size of jib!) ...

The 7" version has the receiver on the left side of the box. How I Designed This This was done in tinkercad. ...The models are available if you want to do modifications:</p> <p>The 5" box : <a...

And all the electronics will cost about $7. Depending on the firmware, you can use as a clock, lamp, creeping line, night light or color music. The design does not use filling, but only walls, so printing is relatively fast and low material...

The built-in supports are designed for a .4mm nozzle and for the size that the model is presented. Use your discretion for which part to use if you resize the model significantly. 2 - The right arm on body_front is a quite fragile, just below the...

If there are any errors or you have requests for special changes to design, please let me know in the comments.&nbsp;All pieces are support free!Let's start with the list of parts you will need to complete the project:3D printed parts (See...

The controller from the matrix is a arduino nano. The hole design is extremely simple so that it cannot go rong. All the parts need to be printed at 20% or higher, the ring need to be printed at 100%. This is the code to set the time on the DS3231:...

Furthermore, it looks like the original design had some Revolve features going on down there, which I wouldn't be able to accurately reproduce anyways. It came out pretty well regardless. You can see how atrocious the 3D sketching was in the pictures...

&nbsp;- INCOMPLETEAdd variation with looser tolerances so pots can rotate freely - INCOMPLETEAdd small washer to fix noise issues some have experiences - INCOMPLETE&nbsp;As with any of my models, feel free to message me with any questions or...

 A lot of my models are designed for the 2.49mm walls that equate to 6 print lines with a 0.4mm nozzle.  Both the Tool Holders and the main Jig are setup to have a color transition at Z height. ... DonationsIf you found this print helpful, sending me a...

This model was designed for print on an Elegoo Mars, can definitely print on any similar or larger format printers. This was not an easy build or an easy print, at all, hopefully I either went through enough trouble that it will be far easier for...

&nbsp;The curved wall to the right of the hole in the picture above broke off like a potato chip.There was serious indentation from the heatsink into the edge of the tabDesign ChangesTo improve reliability, I've made changes to both adapters but the...

I originally designed the tablet holder for our mixing desk, as it can connect to a tablet to use it as an extended screen. For this, we built a wooden cable channel to better hide and protect them. The tablet holder should be able to move back and...

To enhance the design, I applied fillet offsets for slightly rounded vertices. For detailed instructions on building this die, check out my blog: http://inventor-tales.blogspot.com/2012/12/wrapping-up-little-fun-modeling-six.html In case you're...

Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Lamp OptionsLamp options for UV fixtures are determined by UV range.Operators can specify when ordering- UVA (-A part number suffix), UVB (-B) and UVC (-C suffix).F40T8...