xps modeling

Some overhang areas in the inside don't bridge well, so you'll need to do some trimming / post-processing.Updated 5/2/2021:I added aluminum foil tape (HVAC duct tape, buy at any home/hardware store) for 3 reasons:serve as heat spreader so that the...

But 100% fan power isn't necessary, so use an lower Value and take the 100% as "headroom" for bridging etc.The bed leveling is done with an single DC42 IR Sensor (I can highly recommend them). Printing and InstallationAll parts can be printed...

If you get he 25mm deep Nema 17 from STEPPERONLINE store does come with a plug and you can just plug in the stock wiring. Print Settings Printer Brand: Robo 3D Printer: R1 ABS + PLA Model Rafts: No Supports: No Resolution: .2 mm (200 micron) Infill:...

 They're a good working starting point for anyone struggling with a filament.  I've also tuned other types of filaments (see my models here) and you should find, by category:Standard Nozzle (0.4 mm , Hardened Steel, should work for P1P/P1S as...

Note: If you use typically use a negative Horizontal Expansion number in Cura, make sure it doesn't eliminate the in-model hole supports. If these little support towers disappear, cut back on Horizontal Expansion until they re-appear. (For example,...

Stereographic Projection based on the excellent work shared here: https://jasmcole.com/2014/11/01/stereographic-lampshades/#more-650 I used Blender's "Solidify" modifier to add various thicknesses to this model for printing. I recommend printing one...

Subscribe Now! A very good model from Velrock. Time-lapse print video : https://youtu.be/4lXVR1HwAAU <iframe width="560" height="315" src="https://www.youtube.com/embed/4lXVR1HwAAU" title="YouTube video player" frameborder="0"...

After that, go to the model tab, and press the "download" button. Please note: the final dimensions of the Lithophane are 56(w)x75(h)mm, which includes a 1mm border around the entire lithophane. </li> <li>Repeat step 2 above until you have all your...

Well first, customization (as in the mag cozys), cost (may be cheaper if you have a 3d printer already, though i hope you didn't buy a 3d printer just to print mags), and finally, they actually are closer to katanas than talons, meaning that they...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 use_stencil = 0 stencil_shape = 4 stencil_size = 40 stencil_mirror = 0 custom_back_extra_port_x_size = 30...

Note: Scaling down the model too small may not work on all printers. The smaller the part, the more precise your printer should be. 1/2 scale should work well without extra precision. Any smaller will need a printer which supports a step of .05 mm...

...It does give me more confidence this model works both mechanically and visually in the way it's supposed to. <hr> <u><b>Revisions:</b></u> <b>2020-09-04</b>: SABv2 adds an offset of 1mm. Fit was too tight in v1 when accounting for the detent pin.

to remove push from the angled face (from the thickest portion) outward and it will release itself from the extrusion.The ideal position is up against the top of the frame, tighten the extruder and make sure your PTFE tube is pushed in all the way,...

As I'm new to parametric modeling, this solution was done without adhering to full parametric techniques. I'm still learning. The KeyAll HV has two mounting holes, which left 2 open feet for other uses. One foot was left unused, and the other to...

i started with using an other Model as base and didn't check the dimensions 2. i realized my mistake to late XD 3. if i change the scale i would have to split in 3 parts because it would to long for the most Printers 4. i'm to...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_shape = 4 custom_bottom_port_corner_radius = 5 custom_back_camera_y_size = 20 printer_tolerance = 0.4 stencil_pattern_line_thickness = 30...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_shape = 6 custom_bottom_port_corner_radius = 5 custom_back_camera_y_size = 20 printer_tolerance = 0.4 stencil_pattern_line_thickness = 30...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

If you want to use a rasperry pi camera, print out the picasetop_V3_picameraslit.stl for the camera ribbon slit and a pi case like this that accepts a screw - https://www.thingiverse.com/thing:299529 Can the camera position be adjusted for different...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8 custom_top_port_corner_radius...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

I added the sketchup file with the separated into groups printing parts and model of the motherboard, power supply and fan. You can notice, that motherboard is too close to the HDD cage. If you use mini-ITX board with the cooler not higer than 3,5...

Perhaps my specific model of the C270 camera had some differences? Original "c270_hinge_M3_screw.stl" was missing a crucial constriction of the bore for the pin (as viewable in the original camera mount). The edge of it should form an inner lip for...

... list of Remixes. If I have missed something please advise me and I will correct this ASAP. If you do not want your Thing as part of this collection please advise me and I will remove it and try to include an alternate Thing for the missing model.

I didn't even try to 3D model anything because of the sheer size of the base plate, so I cut it out of foamcore. But it could just as well have been the minis sorted into bags instead. The tray is sized at 240x397x56mm externally. If you do paint...

Note: I accidentally had two ⅔ marks on the outer ring in the original model. That has since been corrected but I haven't had a chance to print out a replacement, so the pictures still have the typo</p><h3>How to use</h3><p>Pick a measurement disk...

I would recommend all the bridges honestly.&nbsp;Update Jan 31 2021made the holes for the hex nuts smaller to promote better hold under torqueadded relief cut on the M6 hole, as threading may result in splitting the model on version D1resized the D1...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_corner_radius = 5 custom_left_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

First, I had to model the front of the display to accommodate the RepRap Discount Full Graphics Smart Controller and then I also decided it needed a back to protect the circuit board. Done... Then I decided to tackle the problem of mounting a...