3D printed Crossbow 3d models

Here's a list of things you'll need for the project: To start, print out this box I designed! Here are the project materials. These aren't specifically for this project; they're all items I had lying around from other projects. You can find them on...

It would be fascinating to use a glow-in-the-dark filament to print this part of the model, then recreate the experiment using a UV light. Understanding the function of proteins is a crucial aspect of a biology course. Specifically, students must...

Now have fun printing and installing the brackets. A little tip: Use heatsinks with thermally conductive adhesive and not with the adhesive pads. These are no good. If you like my design please show it with a like or a make here on Thingiverse. Die...

Needs plenty of support when printing it. Please use the shortest machine screws you can for each of the fittings. You need to heat press the nuts all the way into the recesses. Use countersunk head machine screws for the hotend clamp as the top...

To extend the rear arm tubes, you will need: Forward (forward): L:120mm D:15mm Backward (backward): L:130mm D:15mm Printing Information for Parts 80% PLA for power elements and 30% PLA for the rest of the parts. Setup Requirements For this...

Printing is straightforward and there's no need for supports (except for the diffuser), any spans should be OK without them. There's a little slack to allow the diffuser to fit. If your tolerances are a little out, and the face isn't tight in the...

It is one very easy print.This version works and is complete and tested. I put in hollow tubes in many locations so you can put electronics how ever you prefer, inside, outside. Lights in buildings or Christmas tree.update...

40mm to secure the diff cup onto the crown gear.The pictures should help with the assembly.The gears and axles should be PETG the rest can use PLA. I will use 6 couplings in the design: 2 will power the 2 diff boxes and 4 will drive the...

Printing without support is required for this fan duct. Secure the fan with 2 M3 x 10mm screws and attach the duct to the carriage using 2 M3 x 25mm screws, with nut traps built-in for additional tightness. All measurements are in mm. #Response...

I wanted it to be a very secure fit, strong, lightweight, low-profile, inexpensive, easy to print, and to also not damage the surface of the fork. I managed to achieve those goals.&nbsp;</p><p>I got the idea for this project from k-Lite's design,...

Print these parts in PETG or ABS, not PLA. You can finish them as desired; I personally sanded, primed with filler spray, sanded some more, applied primer/filler again, and then spray-painted with clear coat. Automotive paints would be ideal, but...

Everything is designed to print without supports.&nbsp;This project is a work in progress, but current state is usable.Spool Assembly:Attach tie to desired slot. I have found the slot opposite to the hanging hooks tend to position the cord ends in a...

Update: I made a 2nd Gen hub adapter that is much simpler, prints a lot faster and seems to have held up to all the abuse we have put it through over the past week. The plastic wheels/tires on my sons power wheels didn't have enough grip even...

... Note that the edge and corner brackets extend 6mm past the edge of the P5 panels, so make your wood frame 12mm larger than your matrix in each direction. Note - the picture doesn't show all the brackets attached yet because I'm still printing them.

PRINTING ----- Nothing needs supports. I use transparent PLA for everything. I would recommend using the same colour for all mounts, but you could also colour them to match the cap, or code them to the country they come from or something if you...

If you print it, please post a make with pictures of the end result! Thank you! For all Ender 5 and Ender 5 Pro users! By now you probably have your crappy landy power supply clone swapped out for the Meanwell LRS-350-24 power supply! So now you got...

You will greatly simplify the assembly on the Enclorure.Insert the Lid_lock_V2 into the frame_front_V2 and mount on the Enclosure (each of the front parts will be attached with 3 M3x4 screws)assemble and mount the hinge according to step 6 - 10 of...

The mount model is positioned upside-down for printing without support. The interface between the mount and the clamp is a tapered wedge. This takes an instant to drop the Demel into, and it wedges tighter the more it's pressed down. Lifting the...

The only parts from the cad file I plan on printing is the pass through 4 way connectors. They are measured out so that a 3/8th inch Schedule 40 PVC pipe can slide through them and connect on either side. Technically with these connectors you could...

The only parts from the cad file I plan on printing is the pass through 4 way connectors. They are measured out so that a 3/8th inch Schedule 40 PVC pipe can slide through them and connect on either side. Technically with these connectors you could...

Initially named the RR Donnelley Building after the printing company that served as its primary tenant, it later became the corporate headquarters of United Airlines in 2007 following a deal that included acquiring naming rights to the building. This...

base not included very high quality details i will update the files if you have special requests thank you so much for reviewing and commenting file updated 28th Dec 20 smaller cutted parts for easier print Spinosaurus (meaning "spine lizard") is a...

I had to print that after a craftsman tried to shorten the doors length in a rather barbarian style. The door is 83 cm in width - armed with an Ender 3 this translates to 4 parts with 205mm length each, leaving 1 cm uncovered as the door is so...

I haven't done a great deal of printing yet since installing these, but I thought I'd upload now and let people play with it. OK so details: You'll need to drill four holes (each one through the two layers of the base at this point), suggest 5.5mm,...

The one on the left in the picture above is not necessary, if you have already printed the original version is will still work fine. But the one on the right needed to be changed to clear to USB jumper/adapter/180 degree thing.  I chose to use the...

No support is needed while slicing because I hate to deal with it after printing. My dream is to build one real voron by doing mods for ender, so if you like my design, please give me some support though the Tip Designer button, it will truly...

nut_diameter assigned value 12 matching prior statement concerning fastener dimensions now directly correlated related head type specification which dictates form interface compatibility required operating tools attaching part assembly process;...

Now fit the 80 tooth pulley printed part and secure with M5 screws and nuts. Check how long the rod needs to be by fitting the orange metal part that attaches the weights. Measure the gap between this part and the pulley. Remove the metal part and...

(I've worn them and they're actually not uncomfortable) List of the parts needed to print: 2x Nanami_rim.obj 2x Nanami_pads.obj 1x Nanami_nose_bridge.obj The rims are perfectly symmetrical, so don't worry about having to mirror them or anything. The...

I speak up now only for the next generation of silent sufferers, which from what I've witnessed from the inside is the 'True Normal'.) I kind of feel like printing mostly Sixteenth and Eighth notes and rests, to suggest high energy and rhythmic...