3d blender models

This model is intended for but not limited to PETG filament. PETG filament was chosen for its ability to give a little while still being very strong. It could also be printed in TPU or PLA. TPU would probably be pretty awesome, but I have not tried...

This project includes a version of this object with minimal pre-built supports (Level_4_with_Supports.stl) if required.This model has very tight clearances between some parts and may require careful tuning or post-print cleanup to function and fit...

Print the model with the side of the GEARS FACING DOWN. This car is designed to print at 0.2mm layer height. It might not work properly at other layer heights, so i don't recommend it. Some details are as small as 0.4mm x 0.4mm in size, so ensure...

Many thanks to all, I hope you enjoy the model and thanks to Grigor Barseghyan you can see it at https://artisgl.com/ac-cobraThe AC Cobra, sold as the Shelby Cobra in the United States of America, is an Anglo-American sports car with a Ford V8...

Notes: The Moon (which is a hollow sphere) should be printed with 100% infill and with many layers and shells to ensure that the model is printed solid without any air gaps. 3x layers, perimeters and 25% infill is okay for the lampstand. Use an...

Version 4 remains available.\r\n\r\n****************************************************************************************************\r\n\r\n5/7/20 Check out the V3 redesign including large caliber:...

... Sweep, and the Dimension constraint. Any questions about the historical nature of this set can be addressed to Simon at the email address above, and I will try to answer anything on modelling or future edits here in comments. -Ian R. ...

The model is pre sectioned into eleven parts so it can be built on smaller printers, an uncut version it also available.Additional parts2x 8mm diameter 500mm long dowels1x 8mm diameter 168mm long dowel10x 3mm diameter 20mm long pins2x 3mm diameter...

This set contains 5 Warrior Monks of the Order of the Golden Lotus.   Presupported files are included for each model in both STL format and LYS (Lychee Slicer) format so you can rescale them if required.  Presupports have been created and tested by...

2x 22cmx50cmx4mmModel changes (28.07.2021)Retracted all slots on the lower part by 1mm to the inside to fit the 4mm plexiglass sheets. Retracted the inner Plexiglas notches on the upper unit by 1mm.Retracted the adjustment arm 3mm into the case,...

You can manage using “per model settings” in CURA). - Layer Height: 0.28mm works fine for fast printing. 0.2mm would be better but takes time. - No support. - No Build Plate Adhesion The Filament Guide: Same as above except for Support. A small...

This is a somewhat ergonomic case for a handheld model railway throttle which was designed by Peter Akers (flash62au on GitHub). I designed the case for this in Fusion 360 using a new-to-me technique using a form which seems to have worked well...

... the caps from bumping into each other when pressed. Special thanks to the creator of this dummy pushbutton model that I used in the design process (and included in the sketchup files for this thing): https://www.thingiverse.com/thing:2244231

4 bodies are proposed to adapt to the different backfocus according to the reducer marks: 85/86 mm for the Meade and Antares, 105mm for the Celestron (or 86mm for the old Made in Japan models) and the two backfocuses different for ASI cameras (12.5...

The screws I used as a model are https://www.amazon.it/dp/B07V6K4DQS and they will hold the camera in place. The tripod base MCP-03_tripod_base.stl is the other important piece. You MUST have a 1/4” female screw heat insert. Then you will have...

I assume the magwell will fit other TP9 models (minus the Elite, apparently), but I have no way to verify that. ~~Likewise, with the baseplate, I don't know how the spring interfaces with the baseplate on a non-extended Canik magazine, so you're on...

This model does not have the same aesthetic elements as the previous ones (recess), because I found it better to use the smallest module possible and thus save a lot of space, which I know is not much.The new version features reinforced clips, thus...

Not specifically a remix, but a bit of an enhancement, with a nod to the creator of the model I started with. I wanted to have a sweeping light effect for the lighthouse, so I've experimented with two options. In the course of doing this,...

I have also included models for the text "2+" and "3+" so that you can load both the "_lid.stl" file and "_text.stl" file together into your slicer and apply a different color to each, as shown in my pictures. If you don't want to print multi-color,...

The airflow in this model has a much smoother path, starting up in the blower fan rather than just below it. It is split into three channels and smoothly moves the air to a point just below the nozzle. Many part cooling ducts for the Prusa,...

Insure that the backs of the fans (with the label and wire) are facing away from the threadsRun the fan wires down through the cable management catches and into the bottom cable management channelScrew the Core into the Main BodyThread the wires...

Also also: if you get sick of chasing dice when they fire out of the bottom of the dice tower at high speed and scatter over the edge of the table, I would suggest you head over to domino6713's dice tower courtyard model which will help you corral...

I also added a model for a nut holder for the standoffs, designed so you can pause the print and insert a 3mm nut - you have to create the pause yourself, though. The nut holder has a tab that slides in the slot when the idler is mounted, making it...

This procession is presumed to be the cult model for the human followers of his Dionysian Mysteries. In his Thracian mysteries, he wears the bassaris or fox-skin, symbolizing a new life. Dionysus is represented by city religions as the protector of...

The multi-part design lets it work with both TJ and JK models, and also allows you to replace the hangers over time if they wear out. Simply print (2) bases and (4) hangers for each pair of doors. Snap the hangers into the base - the funnel side is...

If you do decide to use the original vactray, you could use the provided small mini trays for other stuff like the Resin promo models (if you dare) or skip printing them and fill the void in the box with the Square, Round and Terrain token trays...

I recommend using a sharpie or modeling paint to make lettering a separate color for better readability. It may also be possible to use a laser cutter to create the components from alternative materials. Evolution of Spring and Ratchet Mechanism: ...

How I Designed This Iterations The virtual model was easy: Create an amulet about the size of the silhouette files using a hemisphere and tube shape in Tinkercad. Drop the silhouette file into Tinkercad as a hole and raise up a mm above the base. I...

About the Model:an mgoi originalSTLs of full body and parts with aligning pins included.making of video: https://youtu.be/7cmkdSqncboAbout the Original Sculpture:ArdhanarishvaraTiruvenkadu, Thanjavur District. Height 101 cm. Around 11th Century...

[Medium Sized Model - 25mm Base] [Presupported in 32mm & 75mm scale]   A Nosmeni who has been brought along as a guest to witness the occasion by Markamin. Though most the Tharameni protested his presence, he used his leverage from his involvement...