3d print bubbling first layer

To achieve this, you can adjust your printer using the following template: https://www.thingiverse.com/thing:5413456 It allows you to adjust the feed rate specific to your filament to obtain precision of the order of a hundredth of a millimeter,...

I highly recommend printing these with PETG rather than with PLA. Also, the magnets can be difficult to insert. Use a flat thick metal tool placed over the magnet while pressing down with your thumb. It's designed to be a snug fit so that superglue...

I have included two versions of the mount, one is with the rail centered on the overall enclosure and the other is with the rail centered on the top part of the enclosure resulting in a slight (5mm) offset from center. I also went ahead and added in...

All necessary parts for a compact, three-dimensional printed mini tri copter modelled after RCExplorer V3 will need to be acquired. This endeavor relies heavily on David Windeståls impressive design and accomplishments. Those wishing to assist David...

If the magnets or bearings are tight in the holes, it could crack the printed part. Just reprint one or half a percent larger. NOTES: (1) Sometimes you might find that the hole is not centered in the blade, which means the blade could be heavy...

Here's the universal parts print list: 1. Left side gantry (with or without eccentric) 2. Right side gantry (with or without eccentric) 3. Gantry front (with or without eccentric) 4. Gantry rear (with or without eccentric) 5. 23mm spacer (replace...

don't apply pressure on the pull. Cover about an inch every stroke, work your way along the blade. Keep the blade edge parallel to the sharpener edge. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 200...

Additionally, we will delve into designing an enclosure using Fusion 360, which will be materialized through printing in transparent-white PETG plastic. This color, in our opinion, not only adds visual appeal to the setup but also allows observing...

When printing these models, it's highly recommended that you use Cura's "Horizontal Expansion" feature with a negative value. A value of -.12 works for me. If they are still too rigid, try -.15, then -.20, and so on. Introducing BuckleBoards, a...

Refer to the link below for more information and print file(STL). https://surplusperson.tistory.com/800 If you found my designs useful, please donate what you think it is worth to my paypal.me. Your donation will be useful for a new housing...

In using the shroud while printing a model that takes up the entire bed, I found that the wires from the extruder need to be routed over the output end of the fan using wire ties, as shown in the new picture above. As I'm using a low-velocity fan,...

**(update 2017 October 12th: it's okay with an original extruder)** For future designs, I am considering rotating some degrees towards the front the connectors for the chain between the extruder and the X-Motor because as you can see on the...

Since I haven't printed all revisions, this remains a Work In Progress, but in reality, I don't plan to make changes anytime soon, and any updates will need to wait until more Rubbermaid containers are purchased. 10/29/2019 - It's been found that...

I made it to test the ball joint and see if it is fun to play with. It's not supposed to look good,don't print this! List of mix n match animals Crocodile: https://www.thingiverse.com/thing:4751955 Minecraft Steve:...

:)Print with support. My support settings in Slic3r which worked great:</p><ul><li>Support on build plate only: yes</li></ul><p>XY separation between an object and its support: 3.5mm BOM:</p><p>LTC1871 step up converter (67mm*43mm) to create 24 V <a...

So unless you're comfortable splicing or unseating and reseating such wires I'd recommend the above linked item as it is plug-and-play; plus it's tidy] Some additional notes: (1) as can be seen in one of the pictures the smaller text I embossed on...

If our accessory size is close to what you need, you may be able to scrap some of the accessory after printing to make it fit. Or if it is too large, you can use some rubber padding to take up the slack. It is always good to use rubber padding to...

&nbsp;It is remarkably powerful for something this size, it will penetrate cardboard and has a maximum range of 15 meters.&nbsp;This is a modular design that allows you to fit which ever Prod (bow) you like&nbsp;they simply slot in and you use a...

A single support (base + 2 side panels) and a nut can be printed for each spool and the spool would only be changed by releasing the wing nuts so the spool screw would not have to be removed. It'll need: -2 bearings 628 / 6-2Z (13x6x5)mm -100mm...

Since I have a large bed(300x300) I can print a standard sized spine in one go, and for the sleeve, the side panels are all intact. If you don't have that bed or you are going with a magazine format, you will have to use the one that cuts everything...

This allows you to rotate your mounted device and/or base to different positions without needing to drill additional holes.\r\n* If you already have a goPro base, you only need to print the one part.\r\n\r\n## Photo Example\r\n\r\nThe example photo...

This miniature comes with optional presupported files for resin printing. These files come as ready to go STL files or Lychee files if you wish to edit the supports for your custom needs. You can find my latest releases over on my Patreon!   Judge,...

This miniature comes with optional presupported files for resin printing. These files come as ready to go STL files or Lychee files if you wish to edit the supports for your custom needs. You can find my latest releases over on my Patreon!   ...

Edit 08/01 - Hey everyone, just as a heads up, this was designed to be the same size as the 'traditional' walker named after a type of battleship but after printing it myself I realize its a little bit bigger then I thought it would be. For...

#Filament Used: Grey PLA: https://www.amazon.com/gp/product/B07T47BH73?ie=UTF8&tag=WisePrints206-20&camp=1789&linkCode=xm2&creativeASIN=B07T47BH73 Transparent Blue PLA...

I don't expect anyone to print this since it's absolutely ridiculous, but maybe in the distant future someone will give it a shot. After doing 3xSS on half the objects on the list, Blender started chugging and my PC started showing its age. The...

You will need these parts printed:1 Case (any variant, read below for info)1 Cover1 Angled Stand (any variant, read below)5 Potentiometer Cap (you can put a tiny piece of filament or a drop of paint in the small hole to make it easier to see how much...

This driver has no Enable pins so the code takes care of this when controlling the speed)2 dc motors (I used some refurbished N20)TP4056 to recharge the batteries2x 18650 batteries connected in parallelvarious screws and wires - usually what you have...

My vision was for a device that: - Utilizes a 6x6 printing bed - Employs hard tac-switches over rubbery elastomers - Has a vertical layout reminiscent of classic GameBoys - Is simple to assemble and modify - Runs on the Raspberry Pi 2, unlike older...

This inner step, which is the distal 5 mm length of the pin, allows insertion of 1.75 mm printing filament, to lock the pin. The pin itself is split with a .75 mm horizontal slice, so the pin can expand when the filament is inserted. The...