3d print game models

This miniature comes with optional presupported files for resin printing. These files come as ready to go STL files or Lychee files if you wish to edit the supports for your custom needs. You can find my latest releases over on my Patreon!   ...

I printed a scan of the front of the hull and then glued it with dichloroethane. For cooling grates, I used modifier objects, as well as the author of the original project. I added mounting brackets and spacers to secure the power supply under...

and post some makes if you use these it lets me know I'm not wasting my time uploading my designs and if you like what you see check out more of my lures at https://www.theneverendingprojectslist.com/ Print Settings Printer Brand: MakerGear Printer: ...

I print it with the cut in the bumper, which you can separate carefully with an exacto. Then wrap the bumper around, and trim the plugs as needed until it fits together well. Then I use my soldering iron (set around 3/medium) to heat up the edges...

Messuhr 20mm ******************************************************Update 16.10.2022Das Update beinhaltet 4 neue Dateien.Messuhr 20mm 05(16)-Skala (durch die Anregung des Makes von CHAOSXSPIRITMessuhr 20mm 05(16)-Gehäuse 2 mit verlängertem...

I printed and tested it with four 10 W blue LEDs (450 nm wavelength), but other types and wavelengths can also be used. Using the 10 W LEDs shown here, an 80 mm fan must be mounted to avoid heating the reaction vials above 30 degrees C. If lower...

Little material and time is required for printing. The "screws" and "nuts" can be pushed onto one another with a little force, the components are too small for a screw connection. I use the fan on the desk and another one to circulate air in a mold...

We merely tighten the hard plastic filter mounting hub against the printed (hard) top rim of the porkchop's stem. This appears to be good enough for me, but you should test it and add a seal if necessary. A flat O-ring with an ID of 22 or 23mm...

It all sounds confusing and over complicated but I can assure you that once the pieces are printed most of the process is fairly straightforward and the other parts to be used can be sourced quite economically. Finally, I will recommend a minimum...

Assembly video (in Russian): https://www.youtube.com/watch?v=rt2GikOnDV8 The parts are printed with PLA plastic, the body and struts are 100% infill, the wheel guard mounts are 75%, the wheels are 50%. When assembled, my copy weighs 1466 grams. ...

Print these two pieces out then hot glue them to your broom and refrigerator. My broom has its brush cut at an angle, so orient it so that it naturally falls over towards the back of the fridge. I designed this for a .85" diameter broom stock. Let...

this should be intuitive ISSUE ADDRESSED 1 OF 3, The manufacturer claims a print area of 240mm x 290mm. (I don't think I was getting even that!), but more could be squeezed out with alternate parts The issue is with the wheels that are mounted to...

The screws go through the mounts (print off Y Rail Mount A and B twice and bolt C onto the back of each) and the belt is zip tied to this. My tests show good hold and adjustability. There are also some for the X rail but they involve a new design for...

I tested it by holding the thermistor onto the print-bed as it warmed up to 80c and I could see the fan getting faster and faster - but it was still really quiet. Even at the lowest (and quietest) default speed it puts out a good amount of air and as...

... made it somewhat modular so you could make them taller or shorter. The outer pieces are printed in vase mode and just glued together.I used a 0.8mm nozzle for the outer transparent parts for some additional speed and rigidity.

Various layouts to organize components and tools to keep everything close by so you can make repairs without leaving the table Print instructionsUn pequeño taller para poder trabajar en el salón de tu casa sin quemar nada y teniendo todas las...

There is a new version of this carriage at https://www.thingiverse.com/thing:3615464 AND an even newer one at https://www.thingiverse.com/thing:3688067 ** ** I'd recommend that newest version instead for better rigidity and simpler printing and...

If you want to use Anet's original M5 screws/t-nuts, just print the parts with 100% infill and drill out the mounting holes with 5.0 or better yet, 5.5mm (to give you some alignment room) drill. Edit: Full screw list, as requested: * 10pcs of 412...

It is composed of 3 parts to be printed: - The main box which contains the plants. - A diffuser located on the upper part of the box and which allows you to water the plants - The frame which is used for the aesthetic aspect (hide the box) as well...

You might want to widen the holes for the screws with a drill (depending on the printing quality you select). 3. Before assembling anything to the case, use a blow torch to warm up the screw brackets and screw in the screws to gently form a thread...

... after days, or use a step-by-step motor or a properly controlled servo motor. I took advantage of the suggestion in the comments to widen the dial, so you can read the time well between 9 and 12, the result seems very good to me. Happy printing!

This miniature comes with optional presupported files for resin printing. These files come as ready to go STL files or Lychee files if you wish to edit the supports for your custom needs. You can find my latest releases over on my Patreon!   ...

einfach Fragen! Print instructionsUnassociated tags: 7 segment, 7 Segment Uhr, LED clock, LED Uhr, RGB Uhr Category: Household Summary Ich benutzte PLA in schwarz und farblos-transparent Benötigt werden folgende Teile Druckteile: jeweils 4 Stück:...

The built-in socket has the advantage that no cables can be seen. Tools you will need: (see the pictures) Hot glue, super glue, soldering iron, screwdriver, ... Print instructionsCOMPONENTS: Attiny85...

The interior is covered with heat-reflecting material to avoid heat loss and also to slightly amplify the internal lighting given by a simple LED lamp with an external switch.The filament used is all dark red PETG eSUN brand, printed at 245 ° with...

Plastic parts printed in PETG, layer 0.2mm, walls/top/bottom 1.2mm, infill 40%. With good part cooling supports are required only for the lower groove of the tool holders. Development log: 04/09/2023 Working sample 04/10/2029 "Head"...

This collection is a curated list for the Gridfinity system that includes Structural prints and common applications. The collection excludes any designs for unique tools or vanity items. ...Please like/favorite the original posts</p><p>If you are...

Assembly Method: So we looked at what was out there and wanted to simplify current designs as much as possible, we also wanted to design for laser cutting so these can be mass produced. -Its laser cut so 100-1000 can be produced a day -We...

I don't remember what size o-rings were used, but print the piston so that it just fits inside the 1-1/4 PVC tube and try different sizes until they make a decent seal. It doesn't need to be tight. I also sealed up three of the pass-through ports...

Print Settings ==================== Nozzle size = 0.4 mm (minimum, smaller better) Layer height = 0.2 mm ###Filament change layer for colours on "300ZXBoxBack": 1) Start (Colour of the background, mine is in white) 2) Layer 14 (All logos outline and...