3d print google maps

10x2.5mm for backplatesome wires AssemblyPrint all partsOutherCase: after the gcode export from prusaSclicer I applied the wood pattern with the python library from MoonCactus with the following settings:...

http://www.thingiverse.com/apps/customizer/run?thing_id=58001 Instructions Using the following options: image_rotation = 30 degrees to enhance viewing pleasure pattern_shape = a geometric design choice with six sides to create complexity 5cornerR = 8...

The lamp used in this setup is an Aglaia 4W LED touch-control lamp featuring a clamp base that was removed to accommodate a longer M6 x 20mm screw for mounting on the printed bracket. The non-conductive material of the bracket prevents electrical...

Now have fun printing and installing the brackets. A little tip: Use heatsinks with thermally conductive adhesive and not with the adhesive pads. These are no good. If you like my design please show it with a like or a make here on Thingiverse. Die...

I made the mistake of printing them on a raft and they broke on me. Go for a brim insted, then be REALLY careful scraping it off your bed. Sources: Garden Rooster by WorksBySolo https://www.thingiverse.com/thing:189558 Chicken by...

to the picture).4) Zip-tie, screw or stick (doublesided tape) the gimbal controller to your plate.be careful that the m2 screw in the middle of the plate doesn't short out the controller!5) If you want print out this nice cover:...

From the original from HeroMe Gen 5 collection (https://www.thingiverse.com/thing:4460970) you will need to print: a. V6 retaining collar b. V6 air dam c. 4010-Lightweight Duct *FORWARD* d. Fan guard if you want... The mounting plate is used to...

It's tough to find a good attachment point and still get a piece that's minimal, doesn't interfere, easily removed during servicing and has the right geometry to get light on the work effectively.Going to run with this version for a while and see how...

It consists of a "flying" assembly (2 parts) and a ground assembly (3 parts) which should print all together in less than an hour. You also need two pieces of string (ideally strong, non-elastic and very thin) or wire and a standard-sized tealight....

steps per mm, UBL. -after doing UBL make sure you turn BL on (in the same menu as UBL -- BL : on is displayed) -make sure you save everything to EEProm -start printing and be ready to fine-tune your first layer with the “Babystepping” – do it in...

I strongly recommend you to print the frame with PETG, it is very robust although slightly heavier than PLA+ (2g). The best GPS for this drone is in my opinion from a Gopro (I have tested Beitian 180 and 220 as well as a small Goteck) which can be...

I have a modified version ready for printing, or you can simply cut out the piece that's in the way and make a new one. That's how I did it. V2: But if you want to order a new display and do some modifications, you can also just swap the original...

Print Settings: Rafts: No Supports: No Resolution: 0.25 Layer 0.4 Nozzle Infill: 10% Triangle Notes: 3 Perimeters, 3 Solid Layers. Build Notes: Attach magnets to the rotor using a good quality superglue. I recommend Gorilla brand superglue with the...

You reuse the axles and bearings that came with your MMU2 kit.Print instructionsTo mount, push the end of the bowden tube from the back of the MMU into the hole on the end of the "Frame". Move the "Frame" on the wall so the tube has a graceful curve...

... professionally done and designed to remove beautifully (provided you have dialled in your printer settings). They are guaranteed to give you one of the best printing experiences you've ever had! Are we allowed to use the term "printgasm"?! ...:-)

[8] Inventor of Juggler: The Wanhao/Makerbot Print Profile Editor - (Alternative to ProfTweak) uploaded it to Thingiverse at http://www.thingiverse.com/thing:679807 and licensed it for reuse under Creative Commons - Attribution - Share Alike. [9]...

I think I had printed all the versions, so everything should fit. If not, tell me. - For everyday use.<br> - Protects your pens from damage and direct sun.<br> - Diameter 53 mm.<br> - Height depends on type. About 160-170 mm.<br> - You have all...

Print Settings Printer Brand: Printrbot Printer: Simple Red Supports: Doesn't Matter Resolution: 0.2 Infill: 20 Notes: Use supports touching buildplate on the legs, gimbal plate, and top plate. ... Custom Section This is the gimbal in action...

I would like to change the base and top part for reducing the print time. Edit your own version using Tinkercad: https://www.tinkercad.com/things/bshg0Q4fTUs-sputnik-pieper-modell-remake To build this project, you will need: * A PCB, which could be...

Note that some of the parts need to have the orientation changed in order to print. Feb 7, 2021 I updated the mount block to cover the wires and prevent them from being damaged. I will soon have the case for the TTGO/Display ready. It uses a...

The smokestacks and the third level were lowered in one of the pictures so that the float could pass under approaching traffic lights.Print SettingsPrinter Brand:CrealityPrinter: Ender 5Rafts:NoSupports: NoResolution:.16mmInfill: 100%Filament:...

Steps: - Print the file - Slide the PTFE into its location at the desired length - Use a felt tip pen to mark the start of the contact on the tube - Take out the tube and cut it round on the outline as on the attached renderings - Replace the tube -...

Printing is straightforward and there's no need for supports (except for the diffuser), any spans should be OK without them. There's a little slack to allow the diffuser to fit. If your tolerances are a little out, and the face isn't tight in the...

What with trying to design mods for my printer, I figured having a virtual model would be super handy - and it got totally out of control!\r\nAs I've seen people complaining about not being able to get plans for the acrylic parts in case they break,...

It is highly recommended to print this box in PETG due to PLA's tendency to deform over time under compression, compromising the box's structural integrity. To further enhance stability, consider supporting it from below with rubber feet, ensuring a...

IMPORTANT: It is designed to be printed in TPU. I used a TPU with the common 95A durometer. It's meant to be flexible and to protect the frame so it grips in a vise properly without damaging the frame. While I was working on cutting the grooves...

Just click the “Support & Join”  button beside my name or here: https://www.printables.com/@GigaPenguin#join:279  Exclusive models are included too! You can also support me through Patreon too:...

**Update** (5 June 2021): You can print test parts to verify your measurements of the diameters and inner ring height without wasting too much time and filament. **Major update** (20 May 2021): I have converted this model into a customizable...

To print a complete set of parts for the offset enclosure (To clarify, this is the area from the IKEA Lack table top the printer sits upon- to the top of the enclosure formed by a 2nd Lack table top), you will need one of each component excluding...

I tried to keep the list of printed parts minimal by creating a two-gear system instead of a more complex scissor extension arm. A unique feature of my design is the guide wheel that supports the tracing gear to keep it level and from falling into...