3d printed honeycomb structure

:) Instructions Well, print: 1 Base 1 Lid 3 Buttons Put the plastic part inside the rectangle in the lid. Put the TreadGaming PCB hardware in. Insert the buttons in the lid. Squeese the sides (to not let the PCB fall out) and turn the base...

For printing I just made everything 50% Gyroidial infill, with ESUN PLA+. Did a bunch of pretty serious drop and smash tests with early iterations and the unit held up pretty damn well. I got the makita mount from somewhere a while back but cant...

------------------------------------------------------------------------------------------------------------------------ Old Description...

Required parts: GT2 Timing Pulleys 40 Tooth 2GT Synchronous Wheel Parts Bore 8mm Aluminium Gear Teeth Width 6mm - 2 GT2 Driver Belt 860-2GT-6 Timing Belt in Closed Loop Rubber L=860mm W=6mm 430 Teeth - 1 (note: not compatible with E10 or CR10 due to...

I was thinking of printing JT3D's Affordable Rock Tumbler but wanted a little more control so I decided to build one based on an Arduino. The main thing is the stepper motor and using its rpm and steps/revolution to get an approximation for how long...

... points. This needs supports for building (you might try flipping it upside-down to check if you need less material - this depends on your printer). Also added full- and half-height main body extensions (these can be printed without support).

I printed the original design and carved and drilled and glued until I got something that would work for me but it lacked elegance – actually it was downright ugly. The original design looks like it was done in Design Spark Mechanical and that...

Hobby Tool Holders This is an initial set of compact hobby tool holders the purpose of which are: Short term tool storage for tools being used on an active project Organization to help keep the bench cleaner To help facilitate rapid tool acquisition...

Astromomia watch in this video: Most of the clock face parts will be the same as those in the Quartz Upgrade, this design includes a version of the clock face (Clock Face w Embedded Numerals) that can be printed in 2 colors where the second color...

A major part of this system are bench dogs, and as the metal ones can be quite expensive and you don't necessarily need that much strength in most tasks I figured I'd design and print a set. Same goes for a variety of additional accessories which...

A major part of this system are bench dogs, and as the metal ones can be quite expensive and you don't necessarily need that much strength in most tasks I figured I'd design and print a set. Same goes for a variety of additional accessories which...

I printed the right and left halves as provided, with no supports but one side had to be flipped 180 in the slicer app. I couldn't do anything with the provided whiskers that stand on-end so I made some up. I decided on 3 different length of...

(And why on earth is Print Screen so close to the Page Down button, anyway?)Mice and trackballs were obvious options too, but just like the keyboard, they required more precision and dexterity than I could muster on the move. I even tried a couple of...

500gm spring coils...

All other things still apply like changing the name of the .txt files to .h and .cpp respectively.  Printing:All parts saved as STL are in the correct orientation, and the only part that needs supports is the head. It only really needs...

I have to find efficient part cooling solution, this one does not cool enough with speeds I am printing now. VERRY IMPORTANT! Use correct lenght screws for motor mount. Slightly too long and mount points will be ruined! Parts needed: 2x 445mm X...

I also wanted to have all the tips and other accessories next to the soldering iron placed on the control block (easily removable because glued with velcro).I added a blue diode for the presence of 24V, a red diode to display the PWM output activity,...

This lathe features: - main carriage knob to intuitive movements, 2.5:1 - reinforced and dust protected tool carriage with C-Beam profile, two sides driven - continuously variable speed via a cheap VFD BLDC controller - fixed tools turret with two...

(Dynamic input) Short cut keys:- Ø Ctrl+A : select all Ø Ctrl+B : Snap on/off Ø Ctrl+C : Copy objects to clipboard Ø Ctrl+D : Dynamic UCS (DUCS) on/off Ø Ctrl+E : To change isoplane in isometric Ø Ctrl+F : Osnap on/off Ø Ctrl+G : Grid on/off Ø Ctrl+H...

...Print Settings Printer: Geeetech A10 Resolution: 0.2 Infill: 20% Notes: While I've been developing these, I've been printing at 0.3 for speed and the results are acceptable, you just need to tidy up some of the small holes. ... Category: Electronics

It contains a 24V 12000 mah rechargeble battery and MoOde audio software.https://moodeaudio.org/Please press on the Like button?Parts needed:Raspberry Pi 3B or 3B+Raspberry Pi 7 inch touchscreenHifiberry AMP2Micro SD card class...

I printed the right and left halves of the mask as provided, with no supports but one side has to be flipped 180 in the slicer app. I couldn't do anything with the original whiskers that stand on-end so I made some. I decided on 3 different length...

It prints in three parts, so that you can print all of them on a flat face with no supports. The pack charges using a 2S balancing lithium battery charger, hence the JST XH 3-pin connector. You should try to find one that supports charging at...

A major part of this system are bench dogs, and as the metal ones can be quite expensive and you don't necessarily need that much strength in most tasks I figured I'd design and print a set. Same goes for a variety of additional accessories which...

A major part of this system are bench dogs, and as the metal ones can be quite expensive and you don't necessarily need that much strength in most tasks I figured I'd design and print a set. Same goes for a variety of additional accessories which...

See how it works here: https://youtu.be/B3C8raQL2_4 Instructions Instructions: You will need to print the following parts (all 0.2mm layer, 4 perimeter, 25% infill): 1 gear.stl 1 worm.stl 1 wormbracket.stl 1 bigpulley.stl 1 yoke.stl 1 bladepulley.stl...

Also (constructive) criticism or exchange of experiences is welcome! Post-Printing Sketch für ARDUINO: int topleft; int topright; int downleft; int downright; int drehen; int heben; void setup() { pinMode(8, OUTPUT); //Heben / Senken pinMode(9,...

... the alarm status</li><li>Any other text you send will be replied 1:1 to you with a note that this command is not known. This is used for communication testing and for future usage of this code for an upcoming other project ;)&nbsp;Happy printing :)

In fact I most often just grab these instead of my actual metal bench dogs unless I really need the sturdiness or precision that my metalPrinting InstructionsYou should be able to get away with 0.2mm layer height easily, the XY-resolution is more...

Simply print the base and cap and 14 disks (mark one of them or print in different color). I recommend rethreading bot cap and base with M12 (that's how i did it) or scaling the cap up a little in x/y. The rules (thanks to...