3d printed honeycomb structure

I would love to see what it is being used for! If you like this thing, have as aswell a look at: https://www.thingiverse.com/thing:3239814 everything that this thing can do can be done as well with the newer thing. But it has a lot more options and...

It is though that below the ice in the surface it is a liquid water ocean, and it was early speculated that this ocean could hold life, with the geotermal heating from the tidal interactions with Jupiter and the other Galilean Moons (Io, Ganymede and...

Your slicer should be able to handle both. The other version is also marked as a source so maybe the original creator will implement these changes in the base version (you can tell this is a remix if you know where to look and he/she might be able to...

(Dimentional Accuracy is always suspect on printed parts so some sanding can be required to fit the magnets.)  Though it isn’t one-of-a-kind, the carnavalis stands as a rare and exceptional airship, originally designed by the visionary circus master...

Using TMC2130 drivers ([plus my other modifications](https://www.thingiverse.com/glabifrons/collections/glabifronss-anycubic-kossel-mods)) with this hotend and Klipper firmware, I was able to print 400mm/s with fairly nice results (very minimal...

Depending on how your printer is configured you may find that some of the threads are incorrectly sized after printing. if that is the case I would recommend drilling them to a 3mm diameter and using M3x4x4mm threaded inserts. there is a widened...

It is a simple flat top that can easily be printed upside down and has an included thread to put in a typical Bowden tube fitting. Please the picture and the model for more information.March 7th 2023 Update: Looking at the design I realized the hot...

10x2.5mm for backplatesome wires AssemblyPrint all partsOutherCase: after the gcode export from prusaSclicer I applied the wood pattern with the python library from MoonCactus with the following settings:...

The print should fit snugly between the power supply connector and the RF shielding. If you happen to have other jacks, just go ahead and check the OpenSCAD source how to modify it according to your needs. ... Finally: Have fun playing the old...

EDIT 01.07.2020: Added a foot to be printed in TPU, one for each corner. Holes are already drilled into the case's bottom; use M3 screws to secure them. This is a fully self-designed BT-Speaker setup that you can download and edit as you like. A...

... using it myself. No guarantees, that this solution works. If you print it, please give Feedback to me and the community (by commenting or posting a make) if the brush works. ... ----------------------------- ATTENTION -----------------------------

- Decreased gap to 5.4 to match the dial indicator (added 1.305mm spacer, with odd shape for printing without supports). - Changed hole to 6.53mm to match dial indicator, and made special bolt to act as a pin for a tight fit. - The hole is now 7mm...

... for a security camera through a piece of glass. 1. As a way of passing USB and power cables through a metal cabinet. ### NOTE The OpenSCAD script generates models with errors, though the errors are fixed by slicers and don't cause printing issues.

I don't expect anyone to print this since it's absolutely ridiculous, but maybe in the distant future someone will give it a shot. After doing 3xSS on half the objects on the list, Blender started chugging and my PC started showing its age. The...

The stands need support around screw recesses to be printed properly. In total each holder requires: - 1 base stand, - 1 coil stand, - 1 rail, - 1 filament guide, - one of the guide tube connectors, - 1 filament wheel, - 6 axis screws, or 5 axis and...

For better print quality all screws holes in the Cover (and also above the nuts holes in the main body) are covered by thin layer (0,24mm). For better understanding please look at Cover in your slicer (level +22 mm). Just use drill or proper screw...

nylon) Available parts: You can choose to print this crab any way you like as there are many parts that allow you to customize its assembly. The joints can have as angle 45°, 90°, 135° and 180°. Each part of the legs or claw can be size 1, 2, 3 or...

If you use a spring coupler, use a stop collar on this end too.\r\n\r\n\r\nI have printed these in PLA with 20% infill. You need closed loop control to make this work properly. You can see more about this in the...

... professionally done and designed to remove beautifully (provided you have dialled in your printer settings). They are guaranteed to give you one of the best printing experiences you've ever had! Are we allowed to use the term "printgasm"?! ...:-)

Also (constructive) criticism or exchange of experiences is welcome! Please also have a look at my designs on https://www.thingiverse.com/rolfmobil/designs and https://cults3d.com/en/users/rolfmobil/creations. under the same username (rolfmobil)......

So the only other way would be just to have a spring cable out of the back, but you still would have to be careful not to rotate it too much as the cable would wrap around.If anybody is interested in me creating a fully functional version than please...

Since I haven't printed all revisions, this remains a Work In Progress, but in reality, I don't plan to make changes anytime soon, and any updates will need to wait until more Rubbermaid containers are purchased. 10/29/2019 - It's been found that...

El Firmware esta compilado para el chip SMT32F1, si tu kingroon es el último modelo necesitas compilarlo para la versión SMT32F4 (mks_robin_nano_v1_3_f4)Link of marlin firmwareMaterial list:1 unit – DDB Extruder V2.11 unit – Motor Nema 17 25mm 1...

For printing: Use any material you like to use, but I would recommend PET at least for the rotary bolt to ensure the knob can withstand some impulse from the spring. Supports are usefull for the spool. Ensure that the control curve is smooth. Avoid...

Use a screwdriver to adjust the tensioner, and with the mirrored version, you need to pull the filament lever to access the screw.Screws neededTool:Buttonhead or cylinderhead4x M2.5 x 6 or M2.5 x 81x M3 x 30 or M3 x 28 (For the mirrored version you...

... why I think I have such poor colors and so much diffusion in my photos. Once the pinhole was made, I cut it and taped it to the backside of my printed adapter with duct tape that I then covered with electrical tape (to avoid internal reflections).

Pretapping advised! Choose any knob style of your liking OpenSCAD file included as always for easy adapting to your personal needs. Enjoy listen to the music! Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No...

40mm to secure the diff cup onto the crown gear.The pictures should help with the assembly.The gears and axles should be PETG the rest can use PLA. I will use 6 couplings in the design: 2 will power the 2 diff boxes and 4 will drive the...

keep additional ons as you see fit for the meter, USB etc - do the same for the live for any separate circuits you may add - create a harness for the banana plugs, and anything else you can before you start assembly - I suggest adding at least...

The pieces I made to hold the bumper buttons haven't been printed or tested by me yet as I used hot glue in an earlier prototype piece. You can use just hot glue to hold them, but this may risk pushing them loose. The contact rings on the SparkFun...