3d printed ps4 controller holder

you might want to widen the holes for the screws with a drill (depending on the printing quality you select) or (as I prefer to do) before assembling anything to the case, use a blow torch to warm up the screw brackets and screw in the screws to...

PRINTING: Use PETG or ABS if possible, PLA will degrade outside after a year or two. Printed with a 0.6mm nozzle. 0.2mm layers. No supports needed. Make sure you do not have any underextrusions to keep the plastic solid and waterproof. In the...

... would like to have one for your printer please post the dimensions in the comments. When printing the connector part 2 or part 5 support is required, but I had the support in the holes, therefore then used support blocker, pay attention to this

It is possible to stretch, tear, or otherwise ruin it, but replacement belts are available online and I found that #117B rubber bands are an adequate substitute.To assemble the new parts, I first recommend to secure the nuts to the printed part. It...

**Update Feb 4, 2016:** Printed one out, and made some changes. Made the groove 1.2mm deep all the way around. The rubber band seats a bit better. Changed the arcs to be 13mm wide by 5mm deep. This accommodates my Nexus 6p in a Speck candyshell case...

The modules start as "printer capsules" sent from earth, and they land in a pack before constructing/printing themselves from a cache of on-board materials. The "Printer Capsule" files show the concept. Each of the modules has 6 sides, with a...

My idea was to view the EL wire thru the clear resin printed part but then quickly realized the EL wire is viewed better from the exposed side. I then realized it would be good to drill some holes so I could string the wire thru it. I mean, I...

#What To Print# For four-square, you will need to print: * 1x centrepiece * 4x edge * 4x corner #Plastic Pipe# You will also need 40mm plastic waste pipe for the frame - I used FloPlas WPO2 40mm White Polypropylene Waste Pipe. '40mm' pipes are...

The 4 printed circuit boards with LM358 are required to be able to integrate the measuring device into the positive supply line, since the measuring devices can only be integrated into the negative line of a load without the additional circuitry,...

you will have to change its orientation as you see fit, my recommendation would be placing the narrow long arm with single hole against the bed and remember to print with support, and place support blockers in the nook if you enjoy the easy life! ...

Since I intended to use the printer in an Ikea LACK enclosure I had to make sure it will not crash into its housing while moving during the prints. Sadly the drag chain of the Y-Axis stuck out a bit too much at the back. The rerouted cables give me...

I had to print this new base a total of 4 times, making adjustments along the way until i got it just how i wanted it and holes in the right places with enough room (for usb cables to plug in properly for instance). The next piece to this, was...

I am printing all these Files to check if everything fits nice together and works. Mayber later some Photos and Videos. Shredder with two 19mm Hexagonal Rods as basic. Each Rod is direct attatched to an slow RPM Synchronmotor - So there is no...

This firmware is meant for the chimera version of the flsun cube and is still somewhat a work in progress as goes for tweaking the settings for better print results. Please keep in mind that I'm not responsible for any damage to you, your printer...

... cut in your dovetail leaving extra material at the bottom initially, as it's very easy to go too deep while widening the dovetail. If you notice that you are filing into the jig stop and print a new one, this will help keep everything in tolerance.

Once the speaker housing fits into the mount correctly reinsert the metal clips to lock in place, there should be a small groove in the stem on the printed housing that the metal clip can slide into.Trim new speaker wires, leave enough slack for the...

Features:Easy to customizeChange the sizesMultiple frame optionsChange the iconUse text instead of a code (useful for double sided prints)Multi-color export (layer-change or inlay)Notes:I've also included the heart cutout template if you just want to...

Instructions: Step 1: The cylinders are printed as a group to prevent problems with bed adhesion. You can separate them by cutting the connections with a hobby knife. Each cylinder has a slot on the back to help position it properly on the center...

For the version with a ball bearing, I used: * 1 Ball Bearing MR105ZZ (ø5xø10x4) (the same one used for wheels) * 2 brass shims ø8xø5x1 * 1 M5x16 bolt + washer + lock nut Check the images: the shims are not symmetrical with respect to part 1, making...

This is a small planter for herbs or small flowers.It uses a wick out of wool or special watering wick cords of cotten which are cheap to buy online. First you have to put the wick sword in the bottom of the plant.Then just screw the planter on...

To glue the arms and the ring: if you have printed them in ABS, just put a drop of acetone on each gluing point, hold the parts together and let them dry for about fifteen minutes; if instead you have printed them in PLA or other materials, the...

Light Gray is next to White) See picture attached for correct wiring If you like, like this thing; it help my stats ;) Please post a picture of your nice setup and a comment If you love my designs, you may also consider tipping me, it helps me a...

This works with my Amscope microscope. Print instructionsPrint in PLA with 0.05mm layers aka Ultra Detail. The printer must be finely tuned because the threads have near zero tolerance. Screw the lens on two turns then back it off one turn, like a...

No support required.Sample image is printed with a 0.2 layer height PLA.Use a different color for each player.Print per player the amount of pieces as listed below.PieceNo. ...per player</td></tr><tr><td style="border:1px solid rgb(0, 0,...

Glue for the printed parts Assembly: Once the parts are printed, make sure the "BODY" is a snug fit into the "BOLT" so it can be slid in and glued in place. Bend the aluminium heat sink into the shape shown with a gap of 11mm. Insert the heat sink...

The aim of the SRT is to enable you to work in a more ergonomic position.Whether you're slim, fat, puny or muscular will also affect your support points and influence your needs.The aim of the SRT is to be able to adapt the inclination to improve...

Since Creality systematically refuses to supply Sermoon D1 customers with spare parts of parts subjected to natural wear, such as Hot End and simli, having some problems with the original, I decided to re-build them, improving them to obtain a...

... G27 Hall Effect Mod V1 by James Burroughs (Video Links at bottom) Printing Instructions: (Print Layout is in Pictures) There is not much stress so I used 4 walls and 4 top and bottom and 10% infill seemed to do the job. Use 100% infill for the cap.

The component that is printed correctly with increasing exposure time is then the correct exposure time. If necessary, watch the video again to avoid making a mistake in the order. E.g. ...part (4) looks good: 1 second for part(1) 1.25 seconds for...

Versions Single Point Variant 1.2 (25 Mar 2022) - Added options for rear screw (Screw_Direction and Screw_Hole_Depth) 1.1 (1 Dec 2020) - Improvements for Thingiverse Customizer 1.0 (4 Nov 2020) - Initial version Dual Point Variant 1.2 (25 Mar 2022)...