3d printed xbox 360 controller shell

A major part of this system are bench dogs, and as the metal ones can be quite expensive and you don't necessarily need that much strength in most tasks I figured I'd design and print a set. Same goes for a variety of additional accessories which...

I have to find efficient part cooling solution, this one does not cool enough with speeds I am printing now. VERRY IMPORTANT! Use correct lenght screws for motor mount. Slightly too long and mount points will be ruined! Parts needed: 2x 445mm X...

A major part of this system are bench dogs, and as the metal ones can be quite expensive and you don't necessarily need that much strength in most tasks I figured I'd design and print a set. Same goes for a variety of additional accessories which...

See how it works here: https://youtu.be/B3C8raQL2_4 Instructions Instructions: You will need to print the following parts (all 0.2mm layer, 4 perimeter, 25% infill): 1 gear.stl 1 worm.stl 1 wormbracket.stl 1 bigpulley.stl 1 yoke.stl 1 bladepulley.stl...

AssortedTilesStone (an assorted collection of Tiles to print together, to use printer time more efficientely) *Bases BaseGen The *gen*eric, solid base BasePittrapa A Base piece to build a pittrap. Put it in place of a normal base. A standard floor...

It prints in three parts, so that you can print all of them on a flat face with no supports. The pack charges using a 2S balancing lithium battery charger, hence the JST XH 3-pin connector. You should try to find one that supports charging at...

(Dynamic input) Short cut keys:- Ø Ctrl+A : select all Ø Ctrl+B : Snap on/off Ø Ctrl+C : Copy objects to clipboard Ø Ctrl+D : Dynamic UCS (DUCS) on/off Ø Ctrl+E : To change isoplane in isometric Ø Ctrl+F : Osnap on/off Ø Ctrl+G : Grid on/off Ø Ctrl+H...

I printed the right and left halves as provided, with no supports but one side had to be flipped 180 in the slicer app. I couldn't do anything with the provided whiskers that stand on-end so I made some up. I decided on 3 different length of...

Otherwise you may PERMANENTLY DAMAGE your lenses due to the glue vapors as they will stain and ruin your otherwise clear glass. I did some light sanding on the inside of the adapters so that they slide on and off more easily. Qwerty_Uieo made some...

A major part of this system are bench dogs, and as the metal ones can be quite expensive and you don't necessarily need that much strength in most tasks I figured I'd design and print a set. Same goes for a variety of additional accessories which...

In v1, a massive block in the middle was supposed to do that, but these two smaller ones do the job just fine and we save some material in the process. While printing, however, I thought of a slightly different way; v2 slides horizontally over the...

I printed the right and left halves of the mask as provided, with no supports but one side has to be flipped 180 in the slicer app. I couldn't do anything with the original whiskers that stand on-end so I made some. I decided on 3 different length...

...Print Settings Printer: Geeetech A10 Resolution: 0.2 Infill: 20% Notes: While I've been developing these, I've been printing at 0.3 for speed and the results are acceptable, you just need to tidy up some of the small holes. ... Category: Electronics

magnets, and the more powerful they are, the better.Note that you need to print two of each InsideScrew, outside_screw, and InsideScrew_plug partsPut a small amount of not-too-powerful glue inside the outer grip (1, above), and stick one magnet...

The small drawers can go in any spot on the right side. For print settings I went with .2 layer height, 3 perimeters (mostly because I wasn't sure on the fit for magnets and pins and having the extra helped to drill or cut out if it was tight),...

Whether this means organizing drawers, creating a catch all tray, setting up a bedside charging station for your devices, or even creating a wall mounted shelving unit, this system can do it all.I had success printing these at a 0.2 mm layer...

The human brain is a highly complex and intricate organ that plays a vital role in controlling our thoughts, emotions, and actions. It is estimated that the average person uses only about 10% of their brain power at any given time, leaving a vast...

Logo Petralak - A Call to Action Logo Petralak is more than just a visual identity; it's a call to action that inspires individuals to take control of their destiny. Petralak logo empowers individuals to strive for excellence, pushing them to new...

The brain, the control center of the body, sends out signals to different parts of the body through the nervous system. This allows humans to move their limbs, digest food, breathe, and perform countless other functions necessary for survival. The...

Humans have an inherent desire to make choices and exert control over their lives. This need is closely tied to our sense of identity and self-worth, as it allows us to express ourselves and pursue our passions. When we are given the freedom to make...

Well, the possibilities of PrusaSlicer (and probably other slicers too) give you the tools to realize this yourself, with a good dose of creativity!Principle.The articulated model is supported at several points with printed springs which in turn are...

This model was inspired by mochr's iss model (found here: https://www.thingiverse.com/thing:4293302) and why can be found in the analysis box below, if you would like a more in-depth document containing the full analysis and design process of this...

Files have been cleared with 3D builder. Current weapons: Eos-Pattern Hot-shot Lasgun v2: A nod to the original, this is what started the project since the only files I could find were just slightly modified regular Kantrael pattern. Has a...

This is a digital 3D printable model of a Hydra miniature for tabletop games.It was modelled based on the diary entries of Giles Grafton. Here is one of the entries concerning this model: The many-faced god I met Father Francisco shortly after I...

Scan the World is a non-profit initiative introduced by MyMiniFactory, through which we are creating a digital archive of fully 3D printable sculptures, artworks and landmarks from across the globe for the public to access for free. Scan the World is...

This is a digital 3D printable model of a Basilisk miniature for tabletop games.It was modelled based on the diary entries of Giles Grafton. Here is one of the entries concerning this model: Trophy hunt I have originally come to the Terragona...

Scan the World is a non-profit initiative introduced by MyMiniFactory, through which we are creating a digital archive of fully 3D printable sculptures, artworks and landmarks from across the globe for the public to access for free. ...Scan the World is...

All you need is a 3D printer and the STL File shown above! The dimensions of the Ghost Clip are 6.55cm x 3.00cm x 0.200cm. This innovative, revolutionary design was engineered by myself and Brendon Wen. His page is linked here:&nbsp;<a...

Scan the World is a non-profit initiative introduced by MyMiniFactory, through which we are creating a digital archive of fully 3D printable sculptures, artworks and landmarks from across the globe for the public to access for free. ...Scan the World is...

The "nose-rest" section of the glasses was formed using the 3D likeness of Ian Wright's head (nose to be exact). This way the glasses will fit like they were made for him (which they were, lol). FLIPS function normally when wearing them...