3d question mark

... the nozzle height off the build plate. 05\05\20 Uploaded CFD Analysis images of the Original Narrow & Mk6 5015 Ducts 04\08\21 Uploaded Duct Base Step File for both Ender 3 & 5 with no thread inserts (original design). Category: 3D Printer Parts

I couldn't find any already-made tool models for this job, so I thought I will make my own. It can also work with the bowden fittings on most 3D printer models, both on the extruder and the hotend side. These fittings often get stuck on my printers,...

For more information, read this article. Material Layer height | Fastest speed | PrusaSlicer profile</tr> 0.2mm | 45mm/sQUALITY 0.2mm | 60mm/sSPEED 0.3mm | 50mm/sDRAFT PLA Download Download Download </tr> PETG Download Download...

I took care of the 2nd issue by 3d printing my own holder for the remote that would fit in a 1-gang wall box and could use a decora wall plate. The plastic button section on the remote is the right width, but is a little bit too short, so the...

... PLA Notes: If you have trouble with bed adhesion, i would recommend adding brim. I was able to print all parts will little to no adhesion problems. I use a glass plate with hair spray. 195C Nozzle 70C Build Plate Category: 3D Printer Accessories

I expect they will be more durable and secure.LicenseCreative Commons - Attribution - Non-Commercial (CC BY-NC 3.0)Changelog2021/04/15 - Update readme instructions2021/04/14 - Updated design files2021/04/11 - Initial commitDesignAutocad Fusion...

We've found a Drawer_Gap of 1.0 (mm) to be sufficient, but results will vary for different 3D printers. If unsure, you can test the gap by printing a drawer of your chosen dimensions and a chest for a single drawer (Drawers_Across set to 1 and...

... anything poking through the plastics. 6) Are you ABSOLUTELY SURE you got ALL your measurements correct? Don't forget that while a well set up 3D printer will do a nice and consistent job what it thinks is a mm may not be exactly a mm! ...

 READ BEFORE PRINTING!This is a non-commercial print, this means you are not allowed to sell files or prints of this model.______________________________________________________________________________________What is this?This is my fifth...

Taylor and Dan the 3D Printing Dad, who were inspired by the brilliant toymakers of your childhood, comes a racing toy that you can print at home and race on any smooth, flat surface! Print enough for you and your friends and race each other! Or...

This is a 3D printable bondage fiddle, which consists of 3 layers that are screwed together. For the Hands the shackles have an eliptical fit, so it should sit very snug, while still allowing you to spinn your hands, and perform tasks :D. I split it...

Depending on your model of 3D printer, you now have the choice to use the original slide that's 0.25mm smaller or the new one that's overall 0.5mm smaller. The only pain in the butt part at this point is removing the support structure from the...

I commonly start plants in an Aerogarden and then once the seedling grows a long enough set of roots, I move it into this bin system.Check out my 3D printed Aerogarden pod design here: https://www.thingiverse.com/thing:4560879Check out my video about...

Well then i would like you to comment down below your designs and we will see who has a better design Anywho, i plugged in a usb cable and plugged in the other to the raspberry pi, and screwed in the two bolts Now it was the moment of truth, to find...

... Base for your Walkers – Classic scale 28mm for tabletop wargames. ...3D format: STL file Don't need supports (you'll receive both versions supported and not) - The files are for personal use only. ...Do not copy or redistribute work (please contact me)

We also realized that our mouth was too thin, so we changed the width of the mouth from 0.25cm to 0.3cm. We also realized that our eyes were in the wrong spot, so we remeasured those dimensions and changed them in our drawing and in our...

based on my mirror array experimentation here: https://www.thingiverse.com/thing:5158449 and https://www.thingiverse.com/thing:5162096 All of which is very much derived from the excellent design here:...

I was already pretty well dialed in with the openbulilds mods, but this pushes it to the next level. You can source used 20mm taz extrusions here: https://itworks3d.com/product/aluminum-extrusion-20mm/ Development thread here:...

Since all printers have varying levels of accuracy print this part and make sure it offers a good snug fit on the motor and shaft before dedicating to printing the large parts in full,, if not scale it until it does and apply that same scaling to the...

3D PRINTING SETTINGS Models are optimized for a 0.4mm nozzle, 0.4mm line width. and 0.2mm layer height. Supports are required and should be set to "everywhere" in your slicer. Use a support roof. I recommend a support roof of 0.4mm thickness at 90...

Hello !Wellcome to my little office with Prusa MINI +.I made industrial lamp with concrete base, retro bulb and soft pad made of recycled rubber.O.10 DETAILPrusament PLANo supports15%We will need: Concrete (fine concrete with small...

This is a Core XY conversion kit for the Ender 5 with Linear rails There is a MK2 version here:https://www.thingiverse.com/thing:4777606 Big shout out to Scott3D for his fabulous work on the Hypercube Evo which I have taken the belt tensioner detail...

... breaking the wire lol admittedly i was working with stuff i have lying around and am bad at soldering. if youve got a bit of 3d modeling skills and are a decent electronics person, in sure you could improve on my design fairly easily. ...good luck!

Cómo configurar los parámetros para personalizar la impresión del pomo en “U” 2.1 Para poder personalizar el pomo en “U” deberá tener instalada en su ordenador la aplicación para diseño 3D OpenSCAD. Se trata de un software libre y se encuentra...

This file you can send to your printer and the tower should be printed out with the different temperature settings. Print instructionsCategory: 3D Printing Tests Summary [2018-03-28] Useri_has_it found out that the only thing to make it work...

The paper was cut to fit over the mask on the 3D-printed back and then held in place using blue painter's tape to hold it in place by the edges. This screen gives a very heavy texture, which reduces resolution somewhat; a thin plastic diffuser sheet...

... Print Settings Printer: Folgertech FT-5 Rafts: No Supports: No Resolution: 250mm or less Infill: 30% Notes: Three bottom layers, three top layers. How I Designed This Designed in Fusion 360 Category: 3D Printer Parts

Longer if you plan to add the cable chain pieces The non antiwobble variant is the same, you just eliminate the wobble parts and add 2 more M5 heat set inserts per x endcap. Print instructionsUnassociated tags: bearing wheel, v slot, v wheel...

Also, because the “hanger” on Ryan's original was a teensy bit too tight to fit on my ¼" plywood strut (which is probably thicker than it‘s supposed to be), I widened the hanger's reach by 1.5mm.Also, I have added a choice of bases — one with and one...

In order to use this setup, you will need to perform extensive modifications to your 3d printer. I've tried to detail as much as I can here, but inevitably you will need to work a few things out for yourself. The setup uses the stock Ender 5...