POS Machine 3d models

There does not seem to be a reliable pattern for what machines need the offset version. DescriptionAfter some issues with cooling the opposite side of the cooling fan duct, I designed this new fan duct that allows air to be directed onto the print...

The FlashForge Finder PLA filament is compatible size-wise (fits inside the machine), so I used that for a long period. Eventually, you run out of colors and I wanted to try the Hatchbox filament. For this to work, you need some kind of external...

The two very long shafts that run the length of machine in lower frame bushings are obviously not printable on an Afinia, so I made smaller shafts (one per crank section) called "elbow shafts". These are a snug but movable fit inside frame bushings...

Toolless accessory mount --- This mount allows you to attach custom addons to your 3D printer with toolless operation for adding additional functionality to your machine, be it vinyl cutting, pen plotting and more. The air duct acts as an...

May be it's safer to reduce the diameter of the tube a bit (sanding paper + drilling machine will do), than make a tight connection by soldering. -The connection between the fexible shaft and the 3mm tube is even harder (photo). I cut a slot into the...

I also made a paper shroud underneath the metal and around the power supply to prevent any metal from getting into the machine during the drilling process. Make sure to vacuum often to keep the area clean. Here is a list of the parts I purchased: ~...

It somewhat hides the externally mounted RC-control-arms from view.To mount the servo's under the steps and buffers, some machining of metal parts was required. Other than this, all additions and modifications to the locomotive are fully...

When I print on my machine they are measuring around 18.0mm - 18.1mm ID. For me this works well with regards to the 18650's I'm using. If however you are noticing an issue with ID being too large or small, please send me a message and I will be sure...

5 x Fingerless Glove hands in various poses (open/wave, open relaxed, closed fist, pointing 1, pointing 2)  DIGITAL KITBASH ONLY - 1 unprimed bolas grenade, 1 canteen, 3 pouches. (Multi Shell) Biker 1 x Warhorse Tracked Bike Chassis, with optional...

Cura--Settings--Printer--Manage Printers--Machine Settings--End G-Code window). Disable M84 command with ";" G4 S300 ; wait 5mins to cool nozzle G0 Z250 ; go up to max height You may adapt commands to your needs. Decrease Z250 part if your printer...

This switch is wired in series with the main power switch on my printer, so either one being off will turn the machine off. This switch is what I used. Make your own decisions, I am not responsible for your reckless behavior. Connectors – you may...

Edit it online https://www.tinkercad.com/things/vyZsNf7c5LJ Use computer generated design data to create enclosures for Apple devices 3D printing can be quicker and less expensive than machining of prototype parts or production of cast or molded...

Machine doesn't save themG28 ;HomeG29 ;Auto level I may find a better Marlin version for my SV05 (I'm using the Ender 5 pro version from Creality for the 4.2.7 board) in which case I'll update this.Filament Spool HolderI use several of these spool...

On the other hand, the visible ringing artifacts wouldn't have been out of place on this machine at half the speed, if that, before I put this mod on it. So at the end of the day it is a vast improvement, but like with most such mods you push out...

Angled feet not only help with printing without supports, but also make the parts look like they are floating above the table, and each other, when viewed from a typical high viewing angle. Print InstructionsPrinting the models on their side as...

= 0.1 Snaps Movement along Either One or Two Axises, Both Are Available According To This Flag Provided at The End of Second Option When Set to True Value Which Will Be Done here now That Makes this Option Useful; Its Units Measurement Also...

If you have a smaller laser, you'll need to edit the DXF files to fit on your machine. The file "top.dxf" contains the top piece, the file "900x1200-2.dxf" has the front, and the remaining pieces are in the file "900x1200-1.dxf". Note that the panel...

The standard TAZ mount has the motor up high, and offset towards the front of the machine, the farthest point of the motor 82mm from the X carriage. My placement puts the motor 36mm closer to the carriage/rails, which should reduce any...

...These modifications are intended to make the display work from the TFT port! Regardless, the parameters of the machine must be set in the Marlin Firmware! ... I do not take any responsibility for the settings, nor for any damage due to wiring errors!

In total it should cost a maximum of $20, which is significantly cheaper than the machined replacement spiders you can find online. I can't guarantee this will fit any other telescope than the Skywatcher 150PDS Explorer, and I won't be making one...

You can find a video of the first build here https://youtu.be/xRNCdrJooAo and of the later iteration here https://youtu.be/4r06BYtSB4M The machine prints slow, but at a consistent quality. The cheap stepper motors are the biggest concern with...

You'll need these - [M3 tap and drill bit that is a bit...

Both versions also include ten holes for fastening the two sections together with M3 x 18 machine or self-tapping screws. Note: The photos are of the first remix where the two sections are of equal width, but I've since changed it so that they're...

Finally something to put your big machine to good use! (So, my apologies, I am not inclined to split anything to accomodate smaller printers, because I wanted something without any unnecessary seams and/or assembly.) The tiles are 30 mm x 30 mm and...

Overview and features:Drive mounting:Drives are slid into place and secured with two machine screws each. Big drive goes into the upper part of the compartment while the smaller drive goes to the lower part. For hot-swappable functionality. you could...

See the videos: https://www.youtube.com/watch?v=2B_UX4fm1Mg&t=78s G-code: In CURA, go to Settings-->Printer-->Manage Printers-->Printers-->Machine Settings-->End G-Code And change the End G-Code as follows (copy the following and replace the original...

I orientate this along the flow axis so that it shows whether the gate is open (along axis) or closed (across axis).Fasten the bearing to the other square socket with an M4 x 20mm bolt.Place the ball inside one tube with the bearing and lever set...

I even rebuild my own front switch completely to make it sturdier and with much better grip.Advantages of my designno use of octoprintno smart-plug requireddisconnects the printer completely from power (phase and neutral are disconnected; better than...

That's bad - it's supposed to stay clean - and that's why the area just above the hotend needs cooling (and needs cool-down so a hot-but-off machine's hot hotend doesn't bake the filament in that area!) A wild guess for Bowden-tube printers...

** VERY IMPORTANT: Since the Probe center is now positioned minus 5mm more to the front of the machine than the center of the nozzle, it will not be able to calculate the right UBL/ABL Bed Level numbers since you're always 5mm off. To compensate for...