Simple iPad Stand 3D printed 3d models

Also (constructive) criticism or exchange of experiences is welcome! Please also have a look at my designs on https://www.thingiverse.com/rolfmobil/designs and https://cults3d.com/en/users/rolfmobil/creations. under the same username (rolfmobil)......

Files to print: ========== - 2x __optical support v3.stl__ - Support for the optical Endstop - 2x __Ender 5 - Endstop trigger v1 15mm.stl__ - Parts to trigger the optical endstop 15mm should be the one you need but I included a shorter one just in...

The new mount plate prints easier. The new mount plate has better wiring management. The new mount plate allows for a small 8x8 heat sink to be adhered to the back of the Huvud board to cool the stepper driver on the reverse side. The new Huvud...

The major innovation in coins the Byzantine’s made was to have the emperor face the front rather than print a profile. Most US coins would then adapt the side profile and bank notes adapt a front facing image, if not cocked to the side just slightly....

The equipment tray and servo lock **must be printed as one assembly**. I separated them so you easily could make servo lock for different servo (in that case I use 1181MG servo). I made the square on the equipment tray floor for you to easy pairing...

The first level is composed of 5 components of which each part has fittings arranged differently so as to allow easy assembly, parts from 1 to 4 are numbered the fifth central fitting part to be assembled last, once the prints are completed, proceed...

I figured if I ever had a print that needed that additional ~5mm of build volume, then I will deal with new lead screws then. I also already have an Ender 5 Pro with a Dual-Z XL upgrade for a whopping 500mm Z build height, (but still only a 220mm X/Y...

Added a photo showing the Endstop in fluorescent green filament. Print Settings Printer: Woodstock Delta Rafts: No Resolution: 0.2mm Infill: 25% Gyroid Filament: Generic PLA, PETG Any Notes: Orientation is often not correct, you will most likely...

----------------------------------- What you will need: * Four of the Corner Posts printed in your choice of plastic. * Two strips of polycarbonate strip 1/8" thick, 4" wide, 2 feet long. (Available from McMaster Carr in the USA part number...

Various layouts to organize components and tools to keep everything close by so you can make repairs without leaving the table Print instructionsUn pequeño taller para poder trabajar en el salón de tu casa sin quemar nada y teniendo todas las...

for those who download an try it, all i did was use m4 bolts stuck inside the ends of the tubes after going through the arms then zip tie around the threaded section of the bolt to keep it from slipping out, but do whatever works best for you, i...

Print Settings ==================== Nozzle size = 0.4 mm (minimum, smaller better) Layer height = 0.2 mm ###Filament change layer for colours on "300ZXBoxBack": 1) Start (Colour of the background, mine is in white) 2) Layer 14 (All logos outline and...

I have NOT built or printed this option, but I am confident it will work fine. You can probably source some thin material to take up any slop in the assembly - even the sheet of foam that is provided in the original tinySA packaging box could work...

I also used the bolts from this in the design, so you might have to drill out a hole or widen the nut insert if you want to use bolts from the above kit): [link](https://www.amazon.com/gp/product/B07VWM4J4L)* spade connectors to attach the boost/buck...

... in Tinkercad. Some of the screen shots show artifacts on the models from the edits, but do not show up on the prints themselves.Also if anyone has a spare Ender 5 carriage plate, I would happily take it off your hands (message me with price).

Furthermore the PLA which I used to print these funnels is partially water repellent so that frictional effects are small. A Better Turbo Funnel ---------------------------- Bernoulli's Theorem states that the flow rate is proportional to the...

The transformer comes in 2 Variants and you could either print it complete or in parts however you want to. ... ________________________ <b>If you like my work please consider supporting me on Patreon.</b> <a...

Again, check several times before you drill. Overview of some assembly steps and setup here: https://youtu.be/QQAKxDcRNgc Print Settings Printer Brand: Prusa Printer: I3 MK3SRafts: No Supports: YesResolution: 200 Infill: 15% Filament: Mainly...

It all sounds confusing and over complicated but I can assure you that once the pieces are printed most of the process is fairly straightforward and the other parts to be used can be sourced quite economically. Finally, I will recommend a minimum...

The flexible hose should be suspended overhead, centered on the work area and should have at least a 4 foot rise with ample slack so as not to place side loads on the tool anywhere within the work area. File Dust-Shoe-Mount.stl may be printed or cut...

Cut in smart pieces for easy printing. Lyzz Kaboom - Goblin Lady (Fantasy Pin-Up)This crazy Goblin lady is passionated about explosives and traps. She recently assembled a huge amount of giant missiles with Zipzaap with the plan to launch a bunch of...

# OpenSCAD Fully parametric drawer cable storage management hive with punch cuts (openscad-hex-cable-hive-fully-parametric)OpenSCAD Fully parametric drawer cable storage management hex hive with punch cutsThis is an OpenSCAD sketch to generate fully...

There will be a lot of soldering, and you'll want to make changes to the CAD and do a few test prints of your own if you want good results. Read further down for more info. === Flaws === Firstly, you should know what you're getting into. To be...

Print all the parts before assembling anything. 4. Start by assembling all the windows, doors, and trim as shown in image 1. 5. Assemble the motor mounts by gluing the two halves together. Ensure you align the holes before gluing. 6. Attach them...

If you'd like to buy a print of this with metal inserts in the drill holes, please check out my gunbroker page: https://www.gunbroker.com/item/858377600 This is version 1.2 of the C93 paddle release jig I previously released. This updated version...

The main point is that the duel disk can now be printed from a single spool, depending on your settings. Then I added some extra features for quality of life. Features: - All slots (monster, spell/trap, graveyard, extra deck) support cards in...

____________________________________________________________________ BetaFlight Tune: ``` set p_pitch = 100 set i_pitch = 50 set d_pitch = 70 set f_pitch = 125 set p_roll = 90 set i_roll = 45 set d_roll = 65 set f_roll = 125 set p_yaw = 65 set i_yaw...

Once you have the wires soldered and a battery in place save your game again remove the cartridge and slide the cover into place. A great tutorial on replacing GB batteries while keeping your save can be found here....

Plus more being added please see table belowSorry Painted in lettering and not double colour printing, Found a very light soft grit sanding made using the fibre tipped acrylic paint pens easier to use.&nbsp;Taken from...

... It was only off .13mm (.0051 inches) at the most, but not really an issue if you have printed the parts already. Here is very short video of this machine working. https://youtu.be/HgV3grxkY44 I also added optional **CantileverStablizer.stl**.